Fiat Talento 2 (2016-2020) Torque Spec Settings

Below you'll find the tightening torques for the Fiat Talento 2 in both Nm and ft/lbs. The first table contains the most-used torque settings. The second table contains all torque spec values I could find.
Most-Used Torque Settings for Talento 2
Nut | Torque (Nm) | Torque (ft/lbs) | Remarks | Source |
---|---|---|---|---|
Wheel lug nuts | 160 | 118 | Steel |
![]() |
Wheel lug nuts | 160 | 118 | Alloy |
![]() |
Drain plug | 50 | 37 |
![]() |
|
Brake caliper bolts | 35 | 26 | Front brake |
![]() |
Brake caliper bolts | 29 | 21 | Rear brake |
![]() |
Front axle nut | 280 | 207 | Front |
![]() |
To make sure these are the correct tightening torque values, you can use the data below to verify this is the right model.
Are these torque settings right for you?
- Production years: 2016 - 2020
- Generation: 2
- Type of van: panel
- Model variant: Base
- Also known as:
All Torque Settings in Tables
General torque settings
Nut | Torque (Nm) | Torque (ft/lbs) | Remarks | Source |
---|---|---|---|---|
Wheel bolts | 30 | 22 | Pre-tighten |
![]() |
Wheel lug nuts | 160 | 118 | Steel |
![]() |
Wheel lug nuts | 160 | 118 | Alloy |
![]() |
Drain plug | 50 | 37 |
![]() |
|
Sump bolt | 12 | 9 |
![]() |
|
Oil filter cover | 25 | 18 |
![]() |
|
Oil pressure sensor | 35 | 26 |
![]() |
|
Cylinder head bolt | 30 | 22 |
![]() |
|
Cylinder block base plate bolt | 25 | 18 |
![]() |
|
Cylinder head cover bolt | 12 | 9 |
![]() |
|
Stud of collector | 8 | 6 |
![]() |
|
Inlet distributor screw | 25 | 18 |
![]() |
|
Exhaust manifold studs | 9 | 7 |
![]() |
|
Exhaust manifold nuts | 15 | 11 | Initial torque |
![]() |
Exhaust manifold nuts | 30 | 22 |
![]() |
|
Alternator bolt | 25 | 18 |
![]() |
|
Clutch pressure plate bolt | 25 | 18 |
![]() |
|
Camshaft bearing cap bolt | 10 | 7 |
![]() |
|
High pressure pump drive camshaft pulley bolt | 30 | 22 |
![]() |
|
Exhaust camshaft pulley bolt | 10 | 7 |
![]() |
|
Inlet camshaft bolt | 20 | 15 |
![]() |
|
Exhaust camshaft bolt | 10 | 7 |
![]() |
|
Brake caliper bolts | 35 | 26 | Front brake |
![]() |
Brake caliper mounting bolts | 105 | 77 | Front brake |
![]() |
Brake caliper bolts | 29 | 21 | Rear brake |
![]() |
Brake caliper mounting bolts | 180 | 133 | Rear brake |
![]() |
Front driveshaft lower arm bolts | 180 | 133 |
![]() |
|
Lower ball joint | 125 | 92 |
![]() |
|
Upper engine tie-bar mounting bolt | 115 | 85 |
![]() |
|
Acoustic tie-rod bolt | 62 | 46 |
![]() |
|
Lower engine tie-bar mounting bolt | 62 | 46 |
![]() |
|
Strut subframe mounting | 105 | 77 | Front axle |
![]() |
Shock absorber mounting bracket | 180 | 133 | Front axle |
![]() |
Shock absorber | 180 | 133 | Rear axle |
![]() |
Con rod bolt | 25 | 18 |
![]() |
|
Power-assisted steering pump assembly | 21 | 15 |
![]() |
|
Front hub carrier assembly | 105 | 77 |
![]() |
|
Wheel hub rotor screws | 8 | 6 | Front |
![]() |
Front axle nut | 280 | 207 | Front |
![]() |
Wheel hub | 105 | 77 | Front |
![]() |
Water pump bolt | 10 | 7 |
![]() |
|
Water pump pulley bolt | 10 | 7 | Minimum torque |
![]() |
Water pump pulley bolt | 20 | 15 | Maximum torque |
![]() |
Accessories belt tensioning roller bolt | 25 | 18 |
![]() |
|
Front anti-roll bar tie rod nuts | 44 | 32 | Front axle |
![]() |
Anti-roll bar clamp | 21 | 15 | Front axle |
![]() |
Did you find the answer to your specific question?
👍 0 👎 1
About TightTorque

Hi, I'm Jim Belt and I own a 1974 Mercedes L508D. I love old vans, especially MBs - and I plan to live in one.
about meLegal information
TightTorque is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com. TightTorque is compensated for referring traffic and business to these companies.
privacy policy