- Your #1 online resource for torque specs
By Flask82 - Photo, Public Domain
Below you'll find the tightening torques for the Toyota Land Cruiser 79 series in both Nm and ft/lbs. The first table contains the most-used torque settings. The tables after it contain all torque spec values I could find.
| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to |
|---|
| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
|---|---|---|---|---|---|---|
| Oil pan | Baffle plate to upper oil pan | 10 | 7 |
|
|
|
| Oil pan | Hex head plugs - LH upper oil pan | 86 | 63 |
|
|
|
| Oil pan | Hex head plugs - front of upper oil pan | 50 | 37 |
|
|
|
| Oil pan | Lower oil pan to upper oil pan | 10 | 7 |
|
|
|
| Oil pan | Sump plug | 38 | 28 |
|
|
|
| Oil pan | Oil cooler pipe flange bolts | 10 | 7 |
|
|
|
| Oil pan | Oil cooler to upper oil pan | 21 | 15 |
|
|
|
| Oil pan | Oil cooler relief valve | 25 | 18 |
|
|
|
| Oil pan | Oil level sensor | 10 | 7 |
|
|
|
| Oil pan | Oil pump outlet pipe to upper oil pan | 10 | 7 |
|
|
|
| Oil pan | Scavenger pump pipe flange bolts | 10 | 7 |
|
|
|
| Oil pan | Upper oil to engine | 25 | 18 |
|
|
|
| Oil pan | Ventilation tube banjo bolt | 29 | 21 |
|
|
|
| Oil pan | Ventilation tube mounting bolt | 29 | 21 |
|
|
|
| Oil filter | Oil filter cover plate | 10 | 7 |
|
|
|
| Oil filter | Oil filter outlet pipe flange bolts | 10 | 7 |
|
|
|
| Oil filter | Oil strainer to rear case | 4.9 | 4 |
|
|
|
| Oil pump | Oil pump cover to engine block bolts | 10 | 7 |
|
|
|
| Oil pump | Oil pump pickup to oil pressure regulator | 10 | 7 |
|
|
|
| Oil pump | Oil supply pump to engine block | 10 | 7 |
|
|
|
| Oil pump | Scavenger pump to engine block | 10 | 7 |
|
|
|
| Oil pump | Oil pump plate separator to rear extension housing | 4.9 | 4 |
|
|
|
| Oil pump | Screw plug to rear extension housing | 29 | 21 |
|
|
|
| Oil pump | Oil pump cover to rear extension housing | 4.9 | 4 | Use Torx socket wrench T30 09042-00010 |
|
|
| Oil pump | Oil receiver to front case | 11.7 | 9 |
|
|
|
| Oil pump | Shift outer lever and inner lever (washer and nut) | 12 | 9 |
|
|
|
| Oil pump | Lever lock pin | 12 | 9 |
|
|
|
| Oil pressure switch | Oil pressure regulator to oil pump | 10 | 7 |
|
|
|
| Oil pressure switch | Oil pressure regulator check valve plug | 50 | 37 |
|
|
|
| Oil pressure switch | Oil pump pressure relief valve plug | 50 | 37 |
|
|
|
| Oil pressure switch | Oil pressure sender unit | 15 | 11 |
|
|
|
| Oil pressure switch | Oil seperator | 10 | 7 |
|
|
|
| Fuel cooler | Engine mounted fuel cooler bolts | 10 | 7 |
|
|
|
| Fuel cooler | Fuel pipe banjo bolt | 21 | 15 |
|
|
|
| Fuel cooler | Fuel pipe bracket bolt | 10 | 7 |
|
|
|
| Cylinder head | Cylinder head bolts | 80 | 59 | Tighten addtion 90° |
|
|
| Cylinder head | Cover silencer bolts | 5 | 4 |
|
|
|
| Intercooler | Cover fasteners | 10 | 7 |
|
|
|
| Intercooler | Fasteners | 20 | 15 |
|
|
|
| Intercooler | Rear support bracket fasteners | 21 | 15 |
|
|
|
| Throttle body | Mountin fasteners | 21 | 15 |
|
|
|
| Intake manifold | EGR pipe to intake pipe | 21 | 15 |
|
|
|
| Intake manifold | Intake pipe to upper intake manifold | 21 | 15 |
|
|
|
| Intake manifold | Lower intake manifold to cylinder head | 21 | 15 |
|
|
|
| Intake manifold | Upper intake manifold to lower intake manifolds | 21 | 15 |
|
|
|
| Intake manifold | Water bypass pipe cylinder block (bracket bolt) | 10 | 7 |
|
|
|
| Intake manifold | Water bypass pipe cylinder block (union bolt) | 59 | 44 |
|
|
|
| Engine block | Rear cover to engine block bolts | 10 | 7 |
|
|
|
| Engine mounts | Engine rear mounting to transfer adapter | 59 | 44 |
|
|
|
| Engine mounts | Crossmember to body | 39 | 29 | Bolt |
|
|
| Engine mounts | Crossmember to engine rest mounting | 76 | 56 | Nut |
|
|
| Camshaft | Camshaft bearing caps (10mm) | 10 | 7 |
|
|
|
| Camshaft | Camshaft bearing caps (12mm) | 21 | 15 |
|
|
|
| Camshaft | Oil pipe banjo bolts | 17 | 13 |
|
|
|
| Camshaft | Timing gear Idler gear thrust plate bolts | 47 | 35 |
|
|
|
| Camshaft | Timing gear Injection pump sprocket bolt | 68 | 50 |
|
|
|
| Camshaft | Vacuum pump to engine bolts | 21 | 15 |
|
|
|
| Crankshaft | Position sensor signal ring to crankshaft sprocket | 10 | 7 |
|
|
|
| Crankshaft | Pulley | 115 | 85 |
|
|
|
| Commonrail | Injector pipe to common rail union nut | 34 | 25 |
|
|
|
| Dipstick | Dipstick tube bolts | 10 | 7 |
|
|
|
| Belt tensioner | No.2 idler pulley bracket | 49 | 36 |
|
|
|
| Timing chains | Cover to timing chain case bolts | 25 | 18 |
|
|
|
| Timing chains | Inner timing chain case to engine bolts (12mm) | 29 | 21 |
|
|
|
| Timing chains | Inner timing chain case to engine bolts (14mm) | 42 | 31 |
|
|
|
| Timing chains | Sprocket to camshafts | 25 | 18 |
|
|
|
| Timing chains | Chain guide bolts | 21 | 15 |
|
|
|
| Timing chains | Tensioner bolts | 10 | 7 |
|
|
|
| Valve cover | Cover | 10 | 7 |
|
|
|
| Valve cover | Cover silencer | 5 | 4 |
|
|
|
| Injectors | Front injection pipe protector plate bolts | 10 | 7 |
|
|
|
| Injectors | Fuel supply pipes to injectors | 34 | 25 |
|
|
|
| Injectors | Fuel supply pipes to commonrail | 34 | 25 |
|
|
|
| Injectors | Fuel supply pipe clamp nuts | 5 | 4 |
|
|
|
| Injectors | Injector clamp bolts | 25 | 18 |
|
|
|
| Injectors | Leakage pipe to injector union bolts | 18 | 13 |
|
|
|
| Injectors | No.1 and No.2 injector pipe protector plate bolts | 10 | 7 |
|
|
| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
|---|---|---|---|---|---|---|
| Differential | Propeller shaft flange on differential | 74 | 55 | Front propeller shaft |
|
|
| Differential | Propeller shaft flange on differential | 88 | 65 | Rear propeller shaft |
|
|
| Differential | Differential rear case set bolts | 88 | 65 | Step 1 (temporarily tightened) |
|
|
| Differential | Differential rear case set bolts | 98 | 72 | Step 2 (loosen then re-tighten) |
|
|
| Differential | Front Differential to front axle housing | 27 | 20 |
|
|
|
| Differential | Front Differential to front propeller shaft | 74 | 55 |
|
|
|
| Differential | Front Differential filler plug | 49 | 36 |
|
|
|
| Differential | Front Differential drain plug | 49 | 36 |
|
|
|
| Clutch pressure plate | Drive plate | 182 | 134 |
|
|
|
| Clutch pressure plate | Clutch disc to input shaft spline | 72 | 53 |
|
|
|
| Clutch pressure plate | Exhaust pipe bracket bolts to Clutch housing | 28 | 21 |
|
|
|
| Clutch pressure plate | Exhaust pipe bracket bolts to Clutch housing | 39 | 29 |
|
|
|
| Clutch pressure plate | Exhaust pipe clamp | 19 | 14 |
|
|
|
| Clutch pressure plate | Exhaust pipe gasket bracket bolts | 38 | 28 |
|
|
|
| Clutch assembly | Clutch release cylinder set bolt | 12 | 9 |
|
|
|
| Transmission mount | Transmission to Engine | 72 | 53 |
|
|
|
| Transmission mount | Transmission to Starter | 39 | 29 |
|
|
|
| Transmission case | Shift lever control retainer to transmission case | 17 | 13 |
|
|
|
| Transfer | Transfer case to transmission | 37 | 27 |
|
|
|
| Transfer | Transfer case to transmission | 68 | 50 |
|
|
|
| Transfer | Front case to rear case | 37 | 27 | Use sealant: Part No. 08833-00080, Three bond 1344, Loctite 242 or equivalent |
|
|
| Transfer | Case cover to rear case | 37 | 27 | Use sealant: Part No. 08826-00090, Three bond 1281 or equivalent |
|
|
| Transfer | Rear case to bearing retainer bolts | 39.2 | 29 |
|
|
|
| Transfer | Rear extension housing bolts | 37 | 27 | Use seal packing: Part No. 08826-00090, Three bond 1281 or equivalent |
|
|
| Transfer | Front extension housing bolts | 37 | 27 | Use seal packing: Part No. 08826-00090, Three bond 1281 or equivalent |
|
|
| Transfer | Power take-off case with gasket | 19 | 14 | Use sealant: Part No. 08833-00080, Three bond 1344, Loctite 242 or equivalent |
|
|
| Transfer | Power take-off cover with gasket | 19 | 14 | Use sealant: Part No. 08833-00080, Three bond 1344, Loctite 242 or equivalent |
|
|
| Transfer | Center differential lock indicator switch to front extension housing | 37 | 27 |
|
|
|
| Transfer | L4 position switch | 37 | 27 |
|
|
|
| Transfer | Neutral position switch | 37 | 27 |
|
|
|
| Transfer | Ball, spring, and screw plug to front case | 19 | 14 | Use sealant: Part No. 08833-00080, Three bond 1344, Loctite 242 or equivalent, Torx socket wrench T40 09042-00020 |
|
|
| Transfer | Motor actuator bolts to front case | 18.1 | 13 | Use sealant: Part No. 08833-00080, Three bond 1344, Loctite 242 or equivalent |
|
|
| Flywheel | Flywheel bolts | 182 | 134 |
|
|
|
| Drive shaft | Propeller shaft flange to companion flange | 74 | 55 | Front propeller shaft |
|
|
| Drive shaft | Propeller shaft flange to companion flange | 88 | 65 | Rear propeller shaft |
|
|
| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to |
|---|
| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
|---|---|---|---|---|---|---|
| Exhaust manifold | Retaining nuts | 36 | 27 |
|
|
|
| Exhaust manifold | Heat shield bolts | 25 | 18 |
|
|
|
| Exhaust manifold | No.2 exhaust manifold pipe (with DPF) | 21 | 15 |
|
|
|
| Exhaust manifold | Exhaust center pipe | 39 | 29 |
|
|
|
| Turbo | Exhaust manifold fasteners | 69 | 51 |
|
|
|
| Turbo | No.1 Turbo intake falnge bolts | 21 | 15 |
|
|
|
| Turbo | Oil drain port flange to turbo | 10 | 7 |
|
|
|
| Turbo | Oil supply bracket to turbo | 10 | 7 |
|
|
|
| Turbo | Support bracket bolts | 49 | 36 |
|
|
|
| EGR cooler | Mounting bolts | 21 | 15 |
|
|
|
| EGR cooler | Pipe flange bolts | 29 | 21 |
|
|
|
| EGR cooler | Pipe insulator boltd to flange pipe | 15 | 11 |
|
|
| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to |
|---|
| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
|---|---|---|---|---|---|---|
| Sway bar links/Stabilizer links | Stabilizer bracket to axle housing | 28 | 21 |
|
|
| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to |
|---|
By TTTNIS - Own work, CC0
