Skoda Octavia 1 (1U) (1996-2010) Torque Spec Settings
Below you'll find the tightening torques for the Skoda Octavia 1 (1U) in both Nm and ft/lbs. The first table contains the most-used torque settings. The tables after it contain all torque spec values I could find.
Most-used torque specs for Skoda Octavia 1 (1U)
Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
---|---|---|---|---|---|---|
Oil pan | Oil drain plug | 40 | 30 |
|
||
Oil filter | Oil filter | 20 | 15 |
|
To make sure these are the correct tightening torque values, you can use the data below to verify this is the right model.
Are these torque settings right for you?
- Production years: 1996 - 2010
- Generation: 1
- Type of van: car
- Model variant: Base
- Also known as:
All Torque Settings in Tables
engine torque settings
Save to email ✉️Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
---|---|---|---|---|---|---|
Oil pan | Oil drain plug | 40 | 30 |
|
||
Oil pan | Oil pan bolt | 15 | 11 |
|
||
Oil pan | Baffle plate bolt | 15 | 11 |
|
||
Oil filter | Oil filter | 20 | 15 |
|
||
Oil filter | Oil filter holder bolt | 15 | 11 | Step 1 |
|
|
Oil pressure switch | Oil pressure switch | 25 | 18 |
|
||
Oil feeder | Oil spray nozzle pressure relief valve | 27 | 20 |
|
||
Oil pump | Oil pump bolts | 15 | 11 |
|
||
Oil pump | Oil pump chain sprocket bolt | 20 | 15 |
|
||
Piston rods | Conrod bearing cap nuts | 30 | 22 | Step 1 |
|
|
Cylinder head | Cylinder head bolts | 40 | 30 | 1st stage |
|
|
Cylinder head | Cylinder head cover to Cylinder head | 10 | 7 |
|
||
Intake manifold | Intake manifold with bottom part of intake manifold to Cylinder head | 10 | 7 |
|
||
Engine block | Cylinder block securing nut | 40 | 30 |
|
||
Engine mounts | Engine mounting bolts | 40 | 30 | Bolts 1, Step 1 |
|
|
Engine mounts | Engine mounting bolt | 25 | 18 | Bolt 2 |
|
|
Engine mounts | Engine mounting bolt | 100 | 74 | Bolt 3 |
|
|
Sensor | MAF sensor fasteners | 4 | 3 | Use a drive socket #10. Use a torque wrench. |
|
|
Alternator | Alternator power cable fastener | 5 | 4 | Use a drive socket #13. Use a torque wrench. |
|
|
Alternator | Alternator to Bracket | 25 | 18 |
|
||
Alternator | Alternator fasteners | 8 | 6 | Use HEX No.8. Use a troque wrench. |
|
|
Alternator | Alternator belt pulley | 65 | 48 |
|
||
Alternator | Connection of generator cable terminal B+ (terminal 30) at alternator | 15 | 11 |
|
||
Starter | Connection of starter cable terminal B+ at starter | 15 | 11 |
|
||
Starter | Starter to Gearbox | 65 | 48 |
|
||
Battery | Connection of battery terminal B+ | 6 | 4 |
|
||
Battery | Connection of battery terminal B- | 6 | 4 |
|
||
Battery | Connection of auxiliary cable of battery terminal B+ | 4 | 3 |
|
||
Camshaft | Camshaft bearing cap bolts | 10 | 7 |
|
||
Camshaft | Camshaft sprocket bolt | 65 | 48 |
|
||
Crankshaft | Crankshaft toothed belt sprocket central bolt | 90 | 66 |
|
||
Crankshaft | Crankshaft bearing cap bolts | 65 | 48 | Step 1 |
|
|
Crankshaft | Crankshaft vibration damper | 25 | 18 |
|
||
Coolant expansion tank | Coolant expansion reservoir and PAS reservoir screw | 10 | 7 |
|
||
Radiator | Fan shroud and radiator mounts bolts | 10 | 7 |
|
||
Air conditioning | Condenser and brackets for refrigerant pipes | 10 | 7 |
|
||
Air conditioning | A/C compressor to Bracket | 45 | 33 |
|
||
Air conditioning | Compressor clutch pulley hexagon nut | 15 | 11 |
|
||
Air conditioning | Refrigerant lines screw | 8 | 6 |
|
||
Belt tensioner/Timing chains | Ribbed V-belt tensioner to Bracket | 25 | 18 |
|
||
Belt tensioner/Timing chains | Tensioning pulley | 45 | 33 |
|
||
Belt tensioner/Timing chains | Chain tensioner with tensioning rail | 25 | 18 |
|
drivetrain torque settings
Save to email ✉️Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
---|---|---|---|---|---|---|
Wheel hub assembly | Steering joint to Front wheel bearing housing | 20 | 15 |
|
||
Wheel hub assembly | Rear wheel hub with wheel bearing and pulse rotor self-locking twelve-point nut | 70 | 52 | Step 1 |
|
|
Wheel hub assembly | Brakes to Front wheel bearing housing | 125 | 92 | FN-3 |
|
|
Wheel hub assembly | Brake caliper to Front wheel bearing housing | 28 | 21 |
|
||
Flywheel/Flex plate | Flywheel/Drive plate bolt | 60 | 44 |
|
||
Flywheel/Flex plate | Driven plate to Torque converter | 60 | 44 |
|
||
Transmission fluid pan | Gearbox housing filler plug | 32 | 24 | Use HEX No.H7. Use a torque wrench. |
|
|
Drive/Axle shaft | Drive shaft nut | 225 | 166 | Use a drive socket #30. Use a torque wrench. |
|
|
Drive/Axle shaft | Rear propshaft screws | 60 | 44 |
|
||
Drive/Axle shaft | Rear axle to Bearing bracket | 45 | 33 | Step 1 |
|
steering torque settings
Save to email ✉️Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
---|---|---|---|---|---|---|
Tie rod end | Tie rod end locknut | 50 | 37 | Use a combination spanner #21. Use a torque wrench. |
|
|
Tie rod end | Front track rod with track rod end self-locking nut | 45 | 33 |
|
||
Steering knuckle | Steering knuckle to tie rod end fastener | 45 | 33 | Use a drive socket #19. Use a torque wrench. |
|
|
Steering rack | Steering joint to Wishbone | 20 | 15 | Step 1 |
|
|
Steering wheel | Steering wheel to Steering column | 75 | 55 |
|
||
Power steering | Hydraulic pump belt pulley bolt | 25 | 18 |
|
exhaust torque settings
Save to email ✉️Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
---|---|---|---|---|---|---|
Exhaust manifold | Exhaust manifold to Cylinder head nuts | 25 | 18 |
|
||
Exhaust manifold | Shield to Exhaust manifold | 25 | 18 |
|
||
Muffler | Front and rear silencer hanger bolts | 25 | 18 |
|
brakes torque settings
Save to email ✉️Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
---|---|---|---|---|---|---|
Disc brake | Front brake caliper guide bolts | 28 | 21 | FS-III |
|
|
Disc brake | Front brake caliper guide bolts | 28 | 21 | FN-3 |
|
|
Disc brake | Rear brake caliper hexagon socket bolts | 30 | 22 |
|
||
Disc brake | Front brake disc screw | 4 | 3 |
|
||
Disc brake | Rear brake disc screw | 4 | 3 |
|
||
Disc brake | Rear brake drum screw | 4 | 3 |
|
||
Brake pedal | Accelerator pedal | 20 | 15 |
|
||
ABS | Front ABS wheel speed sensor hexagon socket bolt | 10 | 7 |
|
||
ABS | Rear ABS wheel speed sensor hexagon socket bolt | 8 | 6 |
|
suspension torque settings
Save to email ✉️Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
---|---|---|---|---|---|---|
Wheels | Front wheel bolt | 120 | 89 |
|
||
Wheels | Rear wheel bolt | 120 | 89 |
|
||
Struts | Front suspension strut self-locking hexagon collar nut | 60 | 44 |
|
||
Struts | Front suspension strut to Suspension strut dome | 60 | 44 |
|
||
Struts | Suspension strut lower fastener | 60 | 44 | Add 90°. Use a combination spanner #18. Use a drive socket #18. Use a torque wrench. |
|
|
Struts | Shock strut piston rod nut | 60 | 44 | Use a drive socket #20.6. Use HEX No.H6. Use a torque wrench. |
|
|
Shock absorbers/shocks | Front shock absorber hexagon collar nut | 60 | 44 |
|
||
Shock absorbers/shocks | Front shock absorber collar nut | 60 | 44 |
|
||
Shock absorbers/shocks | Rear shock absorber to Body | 30 | 22 | Step 1 |
|
|
Shock absorbers/shocks | Rear shock absorber lower hexagon bolt | 60 | 44 |
|
||
Shock absorbers/shocks | Rear shock absorber self-locking hexagon nut | 25 | 18 |
|
||
Shock absorbers/shocks | Rear shock absorber bushing screw | 60 | 44 |
|
||
Shock absorbers/shocks | Rear coupling rod to Pressurized shock absorber screw | 110 | 81 |
|
||
Stabilizer bar | Front anti-roll bar clamp bolt | 25 | 18 |
|
||
Sway bar links/Stabilizer links | Front coupling rod to Suspension strut | 90 | 66 |
|
||
Sway bar links/Stabilizer links | Front coupling rod to Wishbone | 15 | 11 | Step 1 |
|
|
Sway bar links/Stabilizer links | Rear coupling rod to Anti-roll bar nut | 25 | 18 |
|
||
Sway bar links/Stabilizer links | Rod fastening to stabilizer | 15 | 11 | Add 90°. Use a drive socket #16. Use a torque wrench. |
|
|
Control arm | Front fastener control arm to subframe | 70 | 52 | Add 90°. Use a drive socket #18. Use a torque wrench. |
|
|
Control arm | Rear fastener control arm to subframe | 70 | 52 | Add 90°. Use a drive socket #18. Use a torque wrench. |
|
|
Control arm | Steering joint to Front track control arm | 220 | 162 | Step 1 |
|
|
Ball joint | Ball joint fastener | 20 | 15 | Add 90°. Use a combination spanner #19. Use a torque wrench. |
|
|
Ball joint | Ball joint fastener to control arm | 20 | 15 | Add 90°. Use a combination spanner #13. Use a torque wrench. |
|
general torque settings
Save to email ✉️Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to |
---|
Did you find the answer to your specific question?
👍 2 👎 0