Chevrolet Impala Ninth (2006-2013) Torque Spec Settings
By IFCAR - Own work, Public Domain
Below you'll find the tightening torques for the Chevrolet Impala Ninth in both Nm and ft/lbs. The first table contains the most-used torque settings. The tables after it contain all torque spec values I could find.
Most-used torque specs for Chevrolet Impala Ninth
| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
|---|---|---|---|---|---|---|
| Oil pan | Oil pan drain plug | 26 | 19 |
|
|
|
| Spark plugs | Spark plugs | 15 | 11 |
|
|
|
| Water pump | Water pump pulley bolts | 25 | 18 |
|
|
To make sure these are the correct tightening torque values, you can use the data below to verify this is the right model.
Are these torque settings right for you?
- Production years: 2006 - 2013
- Generation: Ninth
- Type of van: car
- Model variant: Base
All Torque Settings in Tables
engine torque settings
Save to email ✉️| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
|---|---|---|---|---|---|---|
| Oil pan | Oil pan drain plug | 26 | 19 |
|
|
|
| Oil pan | Oil pan bolt | 25 | 18 |
|
|
|
| Oil pan | Oil pan side bolt | 50 | 37 |
|
|
|
| Oil filter | Oil filter adapter bolts and stud | 25 | 18 |
|
|
|
| Oil filter | Oil filter adapter | 30 | 22 |
|
|
|
| Oil pump | Oil pump body and cover bolts | 12 | 9 | M6 x 85 bolts |
|
|
| Oil pump | Oil pump body and cover bolts | 16 | 12 | M6 x 95 bolts |
|
|
| Piston rods | Connecting rod bearing cap bolt | 25 | 18 |
|
|
|
| Cylinder head | Generator bolt and stud | 50 | 37 |
|
|
|
| Cylinder head | Gnenerator electrical connector | 30 | 22 |
|
|
|
| Spark plugs | Spark plugs | 15 | 11 |
|
|
|
| Intake manifold | Upper intake manifold bolt | 25 | 18 |
|
|
|
| Intake manifold | Lower intake manifold bolt | 7 | 5 |
|
|
|
| Intake manifold | Intake manifold cover ball stud nut | 5 | 4 |
|
|
|
| Throttle body | Throttle body bolt/nut | 10 | 7 |
|
|
|
| Throttle body | Throttle body stud | 6 | 4 |
|
|
|
| Throttle body | Heater inlet and outlet hose clamp nuts to throttle body stud | 10 | 7 |
|
|
|
| Engine mounts | Frame bolts | 145 | 107 |
|
|
|
| Engine mounts | Frame bolts | 160 | 118 |
|
|
|
| Sensor | ECT Sensor | 20 | 15 |
|
|
|
| Sensor | Oil pressure sensor | 16 | 12 |
|
|
|
| Sensor | A/C refrigerant pressure sensor | 5 | 4 |
|
|
|
| Sensor | MAF/IAT sensor | 10 | 7 |
|
|
|
| Sensor | CMP sensor | 10 | 7 |
|
|
|
| Sensor | CKP Sensor | 10 | 7 |
|
|
|
| Sensor | Knock sensor | 25 | 18 |
|
|
|
| Sensor | APP sensor | 5 | 4 |
|
|
|
| Sensor | MAP sensor and bracket | 25 | 18 |
|
|
|
| Sensor | HO2S Sensor | 42 | 31 |
|
|
|
| Starter | Starter | 10 | 7 |
|
|
|
| Starter | Starter bolts | 43 | 32 |
|
|
|
| Starter | Starter solenoid BAT terminal nut to the starter motor | 10 | 7 |
|
|
|
| Battery | Ignition coil bracket nut | 25 | 18 |
|
|
|
| Battery | Ignition lock cylinder case | 7 | 5 |
|
|
|
| Battery | Battery cable terminal nut | 15 | 11 |
|
|
|
| Battery | Battery cable junction block lead nut | 10 | 7 |
|
|
|
| Battery | Battery tray bolt | 5 | 4 |
|
|
|
| Camshaft | Camshaft position actuator magnet bolts | 10 | 7 |
|
|
|
| Camshaft | Camshaft sprocket | 16 | 12 |
|
|
|
| Crankshaft | Crankshaft main bearing cap | 50 | 37 |
|
|
|
| Crankshaft | Crankshaft balancer bolt | 125 | 92 |
|
|
|
| Water pump | Water pump bolt | 25 | 18 |
|
|
|
| Water pump | Water pump manifold | 60 | 44 |
|
|
|
| Water pump | Water pump manifold | 30 | 22 |
|
|
|
| Water pump | Water pump pulley bolts | 25 | 18 |
|
|
|
| Heater core | Heater inlet and outlet pipe | 25 | 18 | Bolt |
|
|
| Heater core | Heater inlet and outlet pipe | 10 | 7 | Stud |
|
|
| Fuel/Oil cooler | Transaxle oil cooler | 38 | 28 |
|
|
|
| Fuel/Oil cooler | Oil cooler fitting to radiator | 38 | 28 |
|
|
|
| Fuel/Oil cooler | Oil cooler fitting to radiator | 7 | 5 |
|
|
|
| Fuel/Oil cooler | Evaporator tube nut | 17 | 13 |
|
|
|
| Coolant expansion tank | Coolant air bleed cover bolts | 12 | 9 |
|
|
|
| Coolant expansion tank | Coolant recovery reservoirs nuts | 4 | 3 |
|
|
|
| Radiator | Coolant crossover pipe bolts | 50 | 37 |
|
|
|
| Radiator | Engine mount strut to radiator support bolts | 50 | 37 |
|
|
|
| Radiator | Thermostat housing bolt | 15 | 11 |
|
|
|
| Radiator | Cooling fan motor nuts | 6 | 4 |
|
|
|
| Radiator | Transaxle oil cooler bolts | 10 | 7 | Lower radiator support |
|
|
| Radiator | Transaxle oil cooler bolts | 25 | 18 | Upper radiator support |
|
|
| Air conditioning | A/C compressor nut | 50 | 37 |
|
|
|
| Air conditioning | A/C compressor hose block fitting nut to condenser | 17 | 13 |
|
|
|
| Belt tensioner/Timing chains | Belt tensioner bolt | 50 | 37 |
|
|
|
| Belt tensioner/Timing chains | Timing chain tensioner bolts | 21 | 15 |
|
|
|
| Belt tensioner/Timing chains | Engine front cover bolt | 25 | 18 |
|
|
|
| Rocker arm | Rocker arm bolts | 34 | 25 |
|
|
|
| Rocker arm | Rocker arm cover bolts | 10 | 7 |
|
|
|
| Fuel system | Fuel injector rail bolts | 10 | 7 |
|
|
|
| Fuel system | Fuel injector harness connector bracket bolt | 8 | 6 |
|
|
|
| Fuel system | Fuel rail bolts | 10 | 7 |
|
|
|
| Fuel system | Fill pipe bracket bolts | 13 | 10 |
|
|
|
| Fuel system | Fuel fill pipe screws to fuel filter pocket | 3 | 2 |
|
|
drivetrain torque settings
Save to email ✉️| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
|---|---|---|---|---|---|---|
| Wheel hub assembly | Wheel spindle rod end jam nuts | 70 | 52 |
|
|
|
| Wheel hub assembly | Wheel bearing/hub to knuckle bolt | 75 | 55 |
|
|
|
| Wheel hub assembly | Wheel bearing/hub bolts | 139 | 103 |
|
|
|
| Wheel hub assembly | Wheel drive shaft nut | 160 | 118 |
|
|
|
| Wheel hub assembly | Wheel bearing/hub bolts | 130 | 96 |
|
|
|
| Wheel hub assembly | Wheel spindle rod to rear suspension support bolts and nuts | 135 | 100 |
|
|
|
| Clutch assembly | Compressor clutch plate | 12 | 9 |
|
|
|
| Flywheel/Flex plate | Flywheel | 100 | 74 |
|
|
|
| Flywheel/Flex plate | Flywheel to torque converter bolts | 63 | 46 |
|
|
|
| Flywheel/Flex plate | Flex plate | 70 | 52 |
|
|
|
| Transmission fluid pan | Flex plate | 25 | 18 |
|
|
|
| Transmission mount/case | Engine mount bracket to mount nuts | 50 | 37 |
|
|
|
| Transmission mount/case | Engine mount strut bracket to engine lower bolts | 50 | 37 |
|
|
|
| Transmission mount/case | Engine mount strut bracket to engine upper bolts | 25 | 18 |
|
|
|
| Transmission mount/case | Engine mount strut bracket to cylinder head bolts | 50 | 37 |
|
|
|
| Transmission mount/case | Transmission brace bolts | 50 | 37 |
|
|
|
| Transmission mount/case | Transmission bracket bolts | 95 | 70 |
|
|
|
| Transmission mount/case | Transaxle bracket to transaxle mount | 47 | 35 |
|
|
|
| Transmission mount/case | Transaxle mount | 63 | 46 | Lower nuts |
|
|
| Transmission mount/case | Transaxle mount | 47 | 35 | Upper nuts |
|
|
| Transfer | Console shift control retaining nuts | 24 | 18 |
|
|
|
| Transfer | Shift lever and transaxle shift cable bracket bolts to shift cable bracket | 30 | 22 |
|
|
steering torque settings
Save to email ✉️| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
|---|---|---|---|---|---|---|
| Tie rod end | Tie rod end | 70 | 52 |
|
|
|
| Steering column | Ignition lock cylinder case | 7 | 5 |
|
|
|
| Steering shaft | Steering shaft to steering column | 62 | 46 |
|
|
|
| Steering shaft | Steering shaft to power steering gear stub shaft | 48 | 35 |
|
|
|
| Power steering | Engine oil cooler/power steering cooler bracket | 2 | 1 |
|
|
exhaust torque settings
Save to email ✉️| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
|---|---|---|---|---|---|---|
| Exhaust manifold | Exhaust manifold | 42 | 31 |
|
|
|
| Exhaust manifold | Exhaust manifold bolt | 20 | 15 |
|
|
|
| Exhaust manifold | Exhaust manifold shield | 10 | 7 |
|
|
|
| Exhaust manifold | Exhaust crossover pipe nuts | 20 | 15 |
|
|
|
| Exhaust manifold | Exhaust crossover pipe heat shield | 10 | 7 |
|
|
|
| Catalytic converter | Catalytic converter | 42 | 31 |
|
|
brakes torque settings
Save to email ✉️| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
|---|---|---|---|---|---|---|
| Disc brake | Caliper bracket with the bracket bolts | 180 | 133 |
|
|
|
| Disc brake | Caliper bracket bolts | 120 | 89 |
|
|
|
| Disc brake | Bleeder valve | 13 | 10 |
|
|
|
| Disc brake | Brake caliper bolt | 54 | 40 |
|
|
|
| Brake line | Fuel/brake line retainer bolts | 10 | 7 |
|
|
|
| Brake line | Brake hose to caliper bolt to brake caliper | 54 | 40 |
|
|
|
| Brake line | Brake pipe fittings | 18 | 13 |
|
|
|
| Brake pedal | Brake pedal nut and bolt | 40 | 30 |
|
|
|
| Brake pedal | Brake pedal assembly retaining nuts | 25 | 18 |
|
|
|
| Master cylinder | Master cylinder mounting nuts | 33 | 24 |
|
|
|
| Master cylinder | Brake pipe fittings at the master cylinder | 18 | 13 |
|
|
|
| Parking brake | Bracket retainers | 14 | 10 |
|
|
|
| Parking brake | Parking brake mounting screw | 3 | 2 |
|
|
suspension torque settings
Save to email ✉️| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
|---|---|---|---|---|---|---|
| Struts | Strut to knuckle nuts | 130 | 96 |
|
|
|
| Struts | Strut mount nut | 70 | 52 |
|
|
|
| Stabilizer bar | Stabilizer shaft insulator bracket bolts | 42 | 31 |
|
|
|
| Stabilizer bar | Stabilizer shaft bracket nuts | 48 | 35 |
|
|
|
| Sway bar links/Stabilizer links | Stabilizer shaft link nut | 23 | 17 |
|
|
|
| Sway bar links/Stabilizer links | Lower stabilizer shaft link nut to stabilizer shaft link | 50 | 37 |
|
|
|
| Trailing arm | Traling arm bracket | 105 | 77 |
|
|
|
| Trailing arm | Traling arm | 240 | 177 |
|
|
|
| Ball joint | Ball joint nuts | 68 | 50 |
|
|
general torque settings
Save to email ✉️| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to |
|---|
Did you find the answer to your specific question?
👍 1 👎 1
