Jeep Grand Cherokee 3 (2005-2010) Torque Spec Settings
By IFCAR - Own work, Public Domain
Below you'll find the tightening torques for the Jeep Grand Cherokee 3 in both Nm and ft/lbs. The first table contains the most-used torque settings. The tables after it contain all torque spec values I could find.
Most-used torque specs for Jeep Grand Cherokee 3
| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
|---|---|---|---|---|---|---|
| Oil pan | Oil pan drain plug | 34 | 25 |
|
|
To make sure these are the correct tightening torque values, you can use the data below to verify this is the right model.
Are these torque settings right for you?
- Production years: 2005 - 2010
- Generation: 3
- Type of van: car
- Model variant: Base
All Torque Settings in Tables
engine torque settings
Save to email ✉️| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
|---|---|---|---|---|---|---|
| Oil pan | Oil pan bolts | 16 | 12 |
|
|
|
| Oil pan | Oil pan drain plug | 34 | 25 |
|
|
|
| Oil dipstick | Oil dipstick tube to Engine block bolt | 15 | 11 |
|
|
|
| Oil feeder | Oil fill tube bolts | 12 | 9 |
|
|
|
| Oil pump | Oil pump bolts | 28 | 21 |
|
|
|
| Oil pump | Oil pump cover bolts | 12 | 9 |
|
|
|
| Oil pump | Oil pickup tube bolt and nut | 28 | 21 |
|
|
|
| Piston rods | Connecting rod cap bolts | 27 | 20 | Stage 1 |
|
|
| Cylinder head | Cylinder head bolts | 27 | 20 | Step 1, Bolts 1-8 |
|
|
| Cylinder head | Cylinder head bolts | 14 | 10 | Step 2, Bolts 9-12 |
|
|
| Cylinder head | Cylinder head bolts | 26 | 19 | Step 4, Bolts 9-12 |
|
|
| Cylinder head | Cylinder head cover bolts and studs | 12 | 9 |
|
|
|
| Intake manifold | Intake manifold bolts | 12 | 9 |
|
|
|
| Engine block | Engine to Transmission bellhousing bolts | 41 | 30 |
|
|
|
| Engine mounts | Engine mount bracket to Block bolts | 61 | 45 |
|
|
|
| Engine mounts | Rear mount to Transmission bolts | 46 | 34 |
|
|
|
| Alternator | Generator mounting bolts | 28 | 21 | M8 bolts |
|
|
| Alternator | Generator mounting bolts | 54 | 40 | M10 bolts |
|
|
| Camshaft | Camshaft sprocket bolt | 122 | 90 | Non-oiled |
|
|
| Camshaft | Camshaft bearing cap bolts | 11 | 8 |
|
|
|
| Crankshaft | Crankshaft damper bolt | 175 | 129 |
|
|
|
| Water pump | Water pump bolts | 58 | 43 |
|
|
|
| Radiator | Thermostat housing bolts | 12 | 9 |
|
|
|
| Belt tensioner/Timing chains | Timing chain tensioner arm | 28 | 21 |
|
|
|
| Belt tensioner/Timing chains | Timing chain primary tensioner bolts | 28 | 21 |
|
|
|
| Belt tensioner/Timing chains | Timing chain guide bolts | 28 | 21 |
|
|
|
| Belt tensioner/Timing chains | Timing chain cover bolts | 27 | 20 |
|
|
|
| Belt tensioner/Timing chains | Timing drive idler sprocket bolt | 34 | 25 |
|
|
|
| Belt tensioner/Timing chains | Hydraulic tesioner bolts | 28 | 21 |
|
|
drivetrain torque settings
Save to email ✉️| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
|---|---|---|---|---|---|---|
| Flywheel/Flex plate | Flexplate bolts | 95 | 70 |
|
|
|
| Drive/Axle shaft | Counterbalance shaft retaining bolt | 28 | 21 |
|
|
steering torque settings
Save to email ✉️| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to |
|---|
exhaust torque settings
Save to email ✉️| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
|---|---|---|---|---|---|---|
| Exhaust manifold | Exhaust manifold bolts | 25 | 18 |
|
|
|
| Exhaust manifold | Exhaust manifold heat shield nuts | 8 | 6 | Stage 1 |
|
|
brakes torque settings
Save to email ✉️| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to |
|---|
suspension torque settings
Save to email ✉️| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to |
|---|
general torque settings
Save to email ✉️| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to |
|---|
By Vauxford - Own work, CC BY-SA 4.0
Did you find the answer to your specific question?
👍 0 👎 5
