Citroën Berlingo 2 (2008-2018) Torque Spec Settings

ByM 93 - Own work, CC BY-SA 3.0
Below you'll find the tightening torques for the Citroën Berlingo 2 in both Nm and ft/lbs. The first table contains the most-used torque settings. The second table contains all torque spec values I could find.
Most-Used Torque Settings for Berlingo 2
Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Source |
---|---|---|---|---|---|
Wheel bolts | 100 | 74 | Diesel engine |
![]() |
|
Drain plug | 25 | 18 | Diesel engine |
![]() |
|
Oil filter cap | 25 | 18 | Diesel engine |
![]() |
|
Spark plugs | 25 | 18 | 1996-2010 model |
![]() |
|
Front brake caliper mounting bracket bolts | 105 | 77 | 1996-2010 model |
![]() |
|
Timing belt tensioner roller | 23 | 17 |
![]() |
To make sure these are the correct tightening torque values, you can use the data below to verify this is the right model.
Are these torque settings right for you?
- Production years: 2008 - 2018
- Generation: 2
- Model variant: Base
- Also known as:
All Torque Settings in Tables
General torque settings
Nut | Torque (Nm) | Torque (ft/lbs) | Remarks | Source |
---|---|---|---|---|
Wheel bolts | 100 | 74 | Diesel engine |
![]() |
Drain plug | 25 | 18 | Diesel engine |
![]() |
Lower oil sump | 12 | 9 |
![]() |
|
Upper oil sump | 12 | 9 |
![]() |
|
Oil filter cap | 25 | 18 | Diesel engine |
![]() |
Oil pressure switch | 32 | 24 |
![]() |
|
Oil level sensor | 27 | 20 |
![]() |
|
Cylinder head | 20 | 15 | Pre-tightening |
![]() |
Cylinder head | 40 | 30 |
![]() |
|
Spark plugs | 25 | 18 | 1996-2010 model |
![]() |
Air inlet manifold | 13 | 10 |
![]() |
|
Exhaust manifold | 25 | 18 |
![]() |
|
Exhaust manifold studs | 10 | 7 |
![]() |
|
RH engine mounting screws | 60 | 44 |
![]() |
|
Alternator screw | 41 | 30 |
![]() |
|
Clutch mechanism fixing screws | 20 | 15 |
![]() |
|
Camshaft bearings covers screw | 5 | 4 | Pre-tightening |
![]() |
Camshaft bearings covers screw | 10 | 7 |
![]() |
|
Camshaft bearings covers studs | 5 | 4 | Pre-tightening |
![]() |
Camshaft bearings covers studs | 10 | 7 |
![]() |
|
Camshaft pulley | 20 | 15 | Pre-tightening |
![]() |
Front caliper guide pin bolts | 27 | 20 | 1996-2010 model |
![]() |
Front brake caliper mounting bracket bolts | 105 | 77 | 1996-2010 model |
![]() |
Front brake caliper support screw | 33 | 24 | Pre-tighten, Bolt without washer |
![]() |
Front brake caliper support screw | 90 | 66 | Pre-tighten, Bolt with washer |
![]() |
Front brake disc screw | 10 | 7 |
![]() |
|
Front brake caliper screw | 27 | 20 |
![]() |
|
Rear caliper guide pin bolts | 30 | 22 | Diesel engine |
![]() |
Rear brake caliper screw | 35 | 26 |
![]() |
|
Rear brake caliper support screw | 30 | 22 | Pre-tighten |
![]() |
Suspension arm fixing to Subframe nut | 111 | 82 | Front axle |
![]() |
Fixing of pivot lower ball joint to Pivot | 230 | 170 | Front axle |
![]() |
Strut to Pivot fixing screw | 80 | 59 | Front axle |
![]() |
Con-rod screws | 5 | 4 | Pre-tightening |
![]() |
Con-rod screws | 10 | 7 |
![]() |
|
Fasterner fastening power steering pump to Mounting | 21 | 15 |
![]() |
|
Manual transmission fluid filler/Level plug torque | 25 | 18 | MA5 transmission, 1996-2010 model |
![]() |
Manual transmission fluid filler/Level plug torque | 20 | 15 | BE3/5 and BE4/5 transmission, 1996-2010 model |
![]() |
Manual transmission fluid drain plug torque | 25 | 18 | MA5 transmission, 1996-2010 model |
![]() |
Manual transmission fluid drain plug torque | 30 | 22 | BE3/5 and BE4/5 transmission, 1996-2010 model |
![]() |
Wheel hub nut | 325 | 240 | Front axle |
![]() |
Rear hub-disc nut | 300 | 221 | Rear axle |
![]() |
Coolant pump | 4 | 3 | Pre-tightening |
![]() |
Coolant pump | 9 | 7 |
![]() |
|
Timing belt tensioner roller | 23 | 17 |
![]() |
|
Anti-roll bar link rod upper fixing nut | 40 | 30 | Front axle |
![]() |
Anti-roll bar link rod lower fixing nut | 40 | 30 | Front axle |
![]() |
Anti-roll bar bearing fixing screw | 100 | 74 | Front axle |
![]() |
Did you find the answer to your specific question?
👍 8 👎 7