Citroën Jumpy 2 (2007-on) Torque Spec Settings

Photo © Rudolf Stricker (CC-BY-SA 3.0)
Below you'll find the tightening torques for the Citroën Jumpy 2 in both Nm and ft/lbs. The first table contains the most-used torque settings. The second table contains all torque spec values I could find.
Most-Used Torque Settings for Jumpy 2
Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Source |
---|---|---|---|---|---|
Engine oil drain plug | 34 | 25 |
![]() |
||
Oil filter support nuts | 10 | 7 | Pre-tighten |
![]() |
|
Oil filter support nuts | 20 | 15 |
![]() |
||
Front brake caliper bolts | 27 | 20 |
![]() |
||
Rear brake caliper bolts | 35 | 26 |
![]() |
||
Roller tensioner bolts | 57 | 42 |
![]() |
To make sure these are the correct tightening torque values, you can use the data below to verify this is the right model.
Are these torque settings right for you?
- Production years: 2007 - present
- Generation: 2
- Model variant: Base
- Also known as:
All Torque Settings in Tables
General torque settings
Nut | Torque (Nm) | Torque (ft/lbs) | Remarks | Source |
---|---|---|---|---|
Road wheels | 100 | 74 | Steel rims |
![]() |
Road wheels | 90 | 66 | Aluminium rims |
![]() |
Engine oil drain plug | 34 | 25 |
![]() |
|
Upper oil sump bolts | 10 | 7 | Bolts 40mm - 45mm, Pre-tighten |
![]() |
Upper oil sump bolts | 16 | 12 | Bolts 40mm - 45mm |
![]() |
Upper oil sump bolts | 10 | 7 | Bolts 21mm, Pre-tighten |
![]() |
Upper oil sump bolts | 16 | 12 | Bolts 21mm |
![]() |
Upper oil sump bolts | 10 | 7 | Bolts 21mm - 25mm, Pre-tighten |
![]() |
Upper oil sump bolts | 16 | 12 | Bolts 21mm - 25mm |
![]() |
Lower oil sump bolts | 5 | 4 | Pre-tighten |
![]() |
Lower oil sump bolts | 9 | 7 |
![]() |
|
Oil filter support nuts | 10 | 7 | Pre-tighten |
![]() |
Oil filter support nuts | 20 | 15 |
![]() |
|
Oil filter support studs | 7 | 5 |
![]() |
|
Oil pressure switch | 32 | 24 |
![]() |
|
Oil temperature and level sensor | 27 | 20 |
![]() |
|
Cylinder head bolts | 20 | 15 | Pre-tighten |
![]() |
Cylinder head bolts | 60 | 44 |
![]() |
|
Air inlet manifold bolts | 10 | 7 |
![]() |
|
Exhaust manifold nut | 10 | 7 | Pre-tighten |
![]() |
Exhaust manifold nut | 20 | 15 |
![]() |
|
Exhaust manifold stud | 6 | 4 |
![]() |
|
Engine support/Intermediate mounting bolts | 60 | 44 |
![]() |
|
Engine support to Engine flexible mounting nut | 45 | 33 |
![]() |
|
Engine support to Reaction rod bolts | 48 | 35 |
![]() |
|
Lower engine mounting to Cylinder block | 60 | 44 |
![]() |
|
Alternator mounting bolts | 20 | 15 |
![]() |
|
Camshaft bearing cap casing | 5 | 4 | Pre-tighten |
![]() |
Camshaft bearing cap casing | 10 | 7 |
![]() |
|
Camshaft pulley bolts | 20 | 15 | Pre-tighten |
![]() |
Front brake disc bolts | 10 | 7 |
![]() |
|
Front brake caliper bolts | 27 | 20 |
![]() |
|
Front brake caliper support bolts | 190 | 140 |
![]() |
|
Rear brake caliper bolts | 35 | 26 |
![]() |
|
Rear brake disc bolts | 8 | 6 |
![]() |
|
Rear brake caliper support bolts | 108 | 80 |
![]() |
|
Lower suspension arm to Subframe bolt | 65 | 48 | Front suspension |
![]() |
Rear suspension lower arm to Anti-roll bar bearing bolt | 105 | 77 |
![]() |
|
Front suspension lower arm to Body bolt | 125 | 92 | Front suspension |
![]() |
Bottom ball-joint clamp bolt-nut assembly | 70 | 52 | Front suspension |
![]() |
Suspension strut bolt-nut assembly | 92 | 68 | Front suspension |
![]() |
Suspension upper support to Body bolt | 45 | 33 | Front suspension |
![]() |
Suspension strut to Body bolt | 65 | 48 | Front suspension |
![]() |
Rear wheel hub nut | 127 | 94 | Rear suspension |
![]() |
Coolant pump bolts | 16 | 12 |
![]() |
|
Roller tensioner bolts | 57 | 42 |
![]() |
|
Anti-roll bar rod to Damper nut | 70 | 52 | Front suspension |
![]() |
Stabilizing bar bolt | 85 | 63 | Rear suspension |
![]() |
Stabilizing bar nut | 130 | 96 | Rear suspension |
![]() |
Did you find the answer to your specific question?
👍 0 👎 1