Chevrolet Impala Eighth (2000-2005) Torque Spec Settings
ByIFCAR - Own work, Public Domain
Below you'll find the tightening torques for the Chevrolet Impala Eighth in both Nm and ft/lbs. The first table contains the most-used torque settings. The tables after it contain all torque spec values I could find.
Most-used torque specs for Chevrolet Impala Eighth
| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
|---|---|---|---|---|---|---|
| Steering wheel | Wheel nuts | 140 | 103 |
|
|
|
| Steering wheel | Steering wheel | 41 | 30 |
|
|
To make sure these are the correct tightening torque values, you can use the data below to verify this is the right model.
Are these torque settings right for you?
- Production years: 2000 - 2005
- Generation: Eighth
- Type of van: car
- Model variant: Base
All Torque Settings in Tables
engine torque settings
Save to email ✉️| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
|---|---|---|---|---|---|---|
| Oil pan | Oil pan | 14 | 10 |
|
|
|
| Oil pressure switch | Oil pressure test hole plug | 12 | 9 |
|
|
|
| Oil pump | Oil pump bolt | 8 | 6 | M6 x 1.0 x 20 bolts |
|
|
| Oil pump | Oil pump bolt | 12 | 9 | M6 x 1.0 x 85 bolts |
|
|
| Oil pump | Oil pump bolt | 16 | 12 | M6 x 1.0 x 95 bolts |
|
|
| Cylinder head | Cylinder head bolts | 60 | 44 |
|
|
|
| Intake manifold | Vertical lower intake manifold bolts | 7 | 5 |
|
|
|
| Intake manifold | Vertical lower intake manifold bolts | 7 | 5 |
|
|
|
| Throttle body | Throttle body retaining nuts and bolts | 28 | 21 |
|
|
|
| Engine mounts | Engine mount upper nuts | 78 | 58 |
|
|
|
| Engine mounts | Engine mount bracket nuts | 102 | 75 |
|
|
|
| Alternator | Generator pivot bolt | 50 | 37 |
|
|
|
| Alternator | Generator brace nut | 25 | 18 |
|
|
|
| Alternator | Generator pulley shaft nut | 100 | 74 |
|
|
|
| Alternator | Generator bolt | 50 | 37 |
|
|
|
| Starter | Starter bolts | 43 | 32 |
|
|
|
| Starter | Starter solenoid BAT terminal nut | 10 | 7 |
|
|
|
| Battery | Ignition coil to ignition module screws | 5 | 4 |
|
|
|
| Battery | Ignition controle module bracket to engine studs and nuts | 25 | 18 |
|
|
|
| Water pump | Water pump bolts | 10 | 7 |
|
|
|
| Common rail | Water pump pulley bolts | 25 | 18 |
|
|
|
| Heater core | Heater core line clamp screw | 2 | 1 |
|
|
|
| Heater core | Heater core cover screws | 2 | 1 |
|
|
|
| Fuel/Oil cooler | Oil cooler pipe clip bolt | 4 | 3 |
|
|
|
| Fuel/Oil cooler | Oil cooler fittings | 38 | 28 |
|
|
|
| Radiator | Thermostat bypass pipe bolt | 11 | 8 |
|
|
|
| Radiator | Thermostat bypass pipe nut | 25 | 18 |
|
|
|
| Radiator | Thermostat housing bolts | 25 | 18 |
|
|
|
| Air conditioning | Compressor hose to accumulator nut | 16 | 12 |
|
|
|
| Air conditioning | Compressor hose to compressor nut/bolt | 33 | 24 |
|
|
|
| Air conditioning | Compressor hose to condenser nut | 16 | 12 |
|
|
|
| Air conditioning | Suction hose at block fitting bolt | 16 | 12 |
|
|
|
| Air conditioning | Suction hose nut at accumulator | 47 | 35 |
|
|
|
| Rocker arm | Rocker arm bolt | 14 | 10 |
|
|
|
| Rocker arm | Fuel system | 17 | 13 |
|
|
drivetrain torque settings
Save to email ✉️| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
|---|---|---|---|---|---|---|
| Wheel hub assembly | Wheel bearing/hub bolts | 130 | 96 |
|
|
|
| Wheel hub assembly | Hub mounting bolts | 75 | 55 |
|
|
|
| Flywheel/Flex plate | Flywheel | 63 | 46 |
|
|
|
| Drive/Axle shaft | Front wheel drive shaft nut | 215 | 159 |
|
|
steering torque settings
Save to email ✉️| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
|---|---|---|---|---|---|---|
| Steering knuckle | Spindle rods to knuckle nut | 150 | 111 |
|
|
|
| Steering knuckle | Wheel spindle rods to suspension support nut | 140 | 103 |
|
|
exhaust torque settings
Save to email ✉️| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
|---|---|---|---|---|---|---|
| Exhaust manifold | Exhaust manifold pipe stud nuts | 32 | 24 |
|
|
|
| Exhaust manifold | Exhaust crossover pipe nuts | 25 | 18 |
|
|
|
| Exhaust manifold | Exhaust crossover heat shield bolts | 10 | 7 |
|
|
|
| Muffler | Exhaust muffler inlet pipe clamp nuts | 50 | 37 |
|
|
|
| Muffler | Exhaust muffler rear hanger bracket bolts | 25 | 18 |
|
|
|
| Catalytic converter | Catalytic converter | 45 | 33 |
|
|
brakes torque settings
Save to email ✉️| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
|---|---|---|---|---|---|---|
| Disc brake | Caliper bracket bolts | 180 | 133 |
|
|
|
| Disc brake | Brake caliper bleeder valve | 13 | 10 |
|
|
|
| Brake line | Brake pipe fittings | 24 | 18 |
|
|
|
| Brake line | ABS modulator brake pipe fittings | 24 | 18 |
|
|
|
| Brake pedal | Brake pedal mounting nuts | 25 | 18 |
|
|
|
| Master cylinder | Master cylinder brake pipe fittings | 24 | 18 |
|
|
|
| Master cylinder | Wheel cylinder bleeder valve | 7 | 5 | Drum brakes |
|
|
| Master cylinder | Wheel cylinder bleeder valve | 11 | 8 | Disc brakes |
|
|
| Parking brake | Parking brake bolts | 10 | 7 |
|
|
suspension torque settings
Save to email ✉️| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
|---|---|---|---|---|---|---|
| Stabilizer bar | Stabilizer shaft bracket nut | 48 | 35 |
|
|
|
| Sway bar links/Stabilizer links | Stabilizer shaft link nut | 23 | 17 |
|
|
|
| Sway bar links/Stabilizer links | Stabilizer shaft link to strut nuut | 35 | 26 |
|
|
|
| Trailing arm | Trailing arm to knuckle nut | 260 | 192 |
|
|
general torque settings
Save to email ✉️| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to |
|---|
By MercurySable99 - Own work, CC BY-SA 4.0
Did you find the answer to your specific question?
👍 1 👎 1
