Ford Falcon 7 (2008-2016) Torque Spec Settings

OSX, Public domain, via Wikimedia Commons
Below you'll find the tightening torques for the Ford Falcon 7 in both Nm and ft/lbs. The first table contains the most-used torque settings. The tables after it contain all torque spec values I could find.
Most-used torque settings for Ford Falcon 7
Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
---|---|---|---|---|---|---|
Oil sump plug | Engine oil drain plug | 26 | 19 |
|
![]() |
To make sure these are the correct tightening torque values, you can use the data below to verify this is the right model.
Are these torque settings right for you?
- Production years: 2008 - 2016
- Generation: 7
- Type of van: car
- Model variant: Base
All Torque Settings in Tables
engine torque settings
Save to email ✉️Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
---|---|---|---|---|---|---|
Oil pan | Oil pan to cylinder block bolts | 9 | 7 |
|
![]() |
|
Oil pressure switch | Oil pressure sensor | 20 | 15 | apply thread sealant |
|
![]() |
Oil sump plug | Engine oil drain plug | 26 | 19 |
|
![]() |
|
Oil temperature sensor | Oil temperature sensor | 20 | 15 | apply thread sealant |
|
![]() |
Oil pump | Oil pump to cylinder block | 10 | 7 |
|
![]() |
|
Cylinder head | Cylinder head bolts (except front and rear) | 40 | 30 | Step 1: 40Nm - Step 2: Rotate 120° clockwise |
|
![]() |
Cylinder head | Cylinder head bolts (front and rear - X4 bolts) | 30 | 22 | Step 1: 30 Nm - Step 2: Rotate 90° clockwise |
|
![]() |
Spark plugs | 17 | 13 |
|
![]() |
||
Intake manifold | Intake manifold to cylinder head | 17 | 13 | 17-24 Nm |
|
![]() |
Intake manifold | Intake manifold bracket (upper) | 16 | 12 |
|
![]() |
|
Alternator | Alternator breacket (rear) to cylinder block | 25 | 18 |
|
![]() |
|
Water pump | Water pump to cylinder block | 20 | 15 |
|
![]() |
|
Flywheel | Flywheel to crankshaft (manual) | 90 | 66 |
|
![]() |
|
Flywheel | Flywheel to crankshaft (auto) | 70 | 52 |
|
![]() |
|
Thermostat | Thermostat housing to cylinder head | 20 | 15 | apply thread locker |
|
![]() |
Throttle body | Throttle body (M6 screws) | 8 | 6 | 8-12 Nm |
|
![]() |
drivetrain torque settings
Save to email ✉️Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to |
---|
steering torque settings
Save to email ✉️Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to |
---|
exhaust torque settings
Save to email ✉️Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
---|---|---|---|---|---|---|
Exhaust manifold | Exhaust manifold to cylinder head | 27 | 20 |
|
![]() |
|
Exhaust manifold | Exhaust manifold heat shield - lower | 20 | 15 |
|
![]() |
|
Exhaust manifold | Exhaust manifold slip joint bolt | 23 | 17 |
|
![]() |
|
Exhaust manifold | Exhaust manifold slip joint stud | 16 | 12 |
|
![]() |
brakes torque settings
Save to email ✉️Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to |
---|
suspension torque settings
Save to email ✉️Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to |
---|
general torque settings
Save to email ✉️Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to |
---|

OSX, Public domain, via Wikimedia Commons
Did you find the answer to your specific question?
👍 1 👎 4