Ford Falcon 7 (2008-2016) Torque Spec Settings
Below you'll find the tightening torques for the Ford Falcon 7 in both Nm and ft/lbs. The first table contains the most-used torque settings. The tables after it contain all torque spec values I could find.
Most-used torque specs for Ford Falcon 7
Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
---|---|---|---|---|---|---|
Oil pan | Oil pan drain plug | 26 | 19 |
|
||
Spark plugs | Spark plugs | 17 | 13 |
|
||
Differential | Drain plug | 27 | 20 |
|
||
Differential | Drain plug | 30 | 22 |
|
||
Transmission fluid pan | Drain plug | 27 | 20 |
|
||
Wheels | Wheel nuts | 135 | 100 |
|
To make sure these are the correct tightening torque values, you can use the data below to verify this is the right model.
Are these torque settings right for you?
- Production years: 2008 - 2016
- Generation: 7
- Type of van: car
- Model variant: Base
All Torque Settings in Tables
engine torque settings
Save to email ✉️Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
---|---|---|---|---|---|---|
Oil pan | Oil pan drain plug | 26 | 19 |
|
||
Oil pan | Oil pan to Cylinder block/Front cover | 10 | 7 |
|
||
Oil pan | Oil pan to Main bearing cross bolts | 58 | 43 |
|
||
Oil filter | Oil filter adaptor to Cylinder block | 17 | 13 |
|
||
Oil pressure switch | Oil pressure sensor | 20 | 15 |
|
||
Oil pump | Oil pump to Cylinder block | 10 | 7 |
|
||
Oil pump | Oil pump pickup tube to Oil pump | 10 | 7 |
|
||
Oil pump | Oil pump pickup tube to Main bearing bolt | 20 | 15 |
|
||
Piston rods | Connecting rod cap to Connecting rod | 26 | 19 | Step 1 |
|
|
Cylinder head | Cylinder head bolts (except front and rear) | 40 | 30 | Step 1 |
|
|
Cylinder head | Front and rear cylinder head bolts | 30 | 22 | Step 1 |
|
|
Spark plugs | Spark plugs | 17 | 13 |
|
||
Intake manifold | Intake manifold to Cylinder head | 17 | 13 | Minimum torque |
|
|
Intake manifold | Intake manifold to Cylinder head | 24 | 18 | Maximum torque |
|
|
Intake manifold | Intake manifold bracket (upper) | 16 | 12 |
|
||
Intake manifold | Intake manifold bracket (upper) to Manifold | 8 | 6 | Minimum torque |
|
|
Intake manifold | Intake manifold bracket (upper) to Manifold | 12 | 9 | Maximum torque |
|
|
Intake manifold | Intake manifold bracket (upper) to Cylinder head | 8 | 6 | Minimum torque |
|
|
Intake manifold | Intake manifold bracket (upper) to Cylinder head | 12 | 9 | Maximum torque |
|
|
Intake manifold | Intake manifold pencil strut (lower) | 20 | 15 |
|
||
Intake manifold | Intake manifold pencil strut (lower) to Manifold | 17 | 13 | Minimum torque |
|
|
Intake manifold | Intake manifold pencil strut (lower) to Manifold | 24 | 18 | Maximum torque |
|
|
Intake manifold | Intake manifold pencil strut (lower) to Cylinder head | 17 | 13 | Minimum torque |
|
|
Intake manifold | Intake manifold pencil strut (lower) to Cylinder head | 24 | 18 | Maximum torque |
|
|
Intake manifold | Intake manifold pencil strut (lower) to Engine mount support | 44 | 32 | Minimum torque |
|
|
Intake manifold | Intake manifold pencil strut (lower) to Engine mount support | 55 | 41 | Maximum torque |
|
|
Intake manifold | Intake manifold ETB | 8 | 6 | Minimum torque |
|
|
Intake manifold | Intake manifold ETB | 12 | 9 | Maximum torque |
|
|
Intake manifold | Intake manifold MTV | 5 | 4 | Minimum torque |
|
|
Intake manifold | Intake manifold MTV | 6 | 4 | Maximum torque |
|
|
Intake manifold | Intake manifold dip stick tube | 10 | 7 |
|
||
Engine mounts | Engine mount bracket to Cylinder block | 50 | 37 |
|
||
Engine mounts | Engine mount to Engine mount bracket | 102 | 75 |
|
||
Sensor | Intake manifold pressure/temperature sensor | 2 | 1 |
|
||
Sensor | Oil temperature sensor | 20 | 15 |
|
||
Sensor | Knock sensor to Cylinder block | 20 | 15 | Minimum torque |
|
|
Sensor | Knock sensor to Cylinder block | 25 | 18 | Maximum torque |
|
|
Sensor | Crankshaft position sensor to Timing cover | 10 | 7 | Minimum torque |
|
|
Sensor | Crankshaft position sensor to Timing cover | 12 | 9 | Maximum torque |
|
|
Sensor | Camshaft position sensor to Cylinder head | 9 | 7 |
|
||
Sensor | Cylinder head temperature sensor to Cylinder head | 15 | 11 |
|
||
Alternator | Alternator bracket (rear) to Cylinder block | 25 | 18 |
|
||
Camshaft | Variable cam timing unit to Camshaft | 20 | 15 | Step 1 |
|
|
Camshaft | Cam caps to Cylinder head | 10 | 7 |
|
||
Camshaft | Oil control valve seals to Cam cover | 7 | 5 |
|
||
Camshaft | Cam cover to Cylinder head | 13 | 10 | Front two long bolts |
|
|
Camshaft | Cam cover to Cylinder head | 10 | 7 | Six short bolts |
|
|
Crankshaft | Main bearing cap bolts | 85 | 63 |
|
||
Crankshaft | Crankshaft vibration damper/Front pulley to Crankshaft | 145 | 107 |
|
||
Common rail | Fuel rail to Intake manifold | 8 | 6 | Minimum torque |
|
|
Common rail | Fuel rail to Intake manifold | 12 | 9 | Maximum torque |
|
|
Water pump | Water pump | 20 | 15 |
|
||
Heater core | Heater tube to Thermostat housing | 20 | 15 |
|
||
Heater core | Heater tube to Block (exhaust side) | 27 | 20 |
|
||
Radiator | Thermostat housing to Cylinder head | 20 | 15 |
|
||
Belt tensioner/Timing chains | Accessory drive belt tensioner securing bolt to Front cover | 25 | 18 |
|
||
Belt tensioner/Timing chains | Accessory drive belt tensioner pulley securing bolt to Tensioner arm | 35 | 26 |
|
||
Belt tensioner/Timing chains | Timing chain fixed chain guide to Cylinder block and cylinder head | 20 | 15 |
|
||
Belt tensioner/Timing chains | Timing chain tensioner to Cylinder head | 9 | 7 |
|
||
Belt tensioner/Timing chains | Timing chain guide pivot bolt to Oil pump | 47 | 35 |
|
||
Belt tensioner/Timing chains | Timing chain guide pivot nut | 9 | 7 |
|
||
Belt tensioner/Timing chains | Timing cover to Cylinder block | 28 | 21 |
|
||
Valve cover | Spark plug cover to Rocker cover | 7 | 5 |
|
||
Valve cover | Ignition coil to Rocker cover | 24 | 18 |
|
drivetrain torque settings
Save to email ✉️Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
---|---|---|---|---|---|---|
Clutch pressure plate | Clutch pressure plate to Flywheel | 22 | 16 | Non-turbo |
|
|
Clutch assembly | Clutch housing to Engine bolts (upper) | 60 | 44 |
|
||
Clutch assembly | Clutch housing to Engine bolts (lower) | 40 | 30 |
|
||
Flywheel/Flex plate | Flywheel to Crankshaft | 90 | 66 |
|
||
Flywheel/Flex plate | Flywheel to Crankshaft | 70 | 52 |
|
||
Flywheel/Flex plate | Manual flywheel housing to Block | 50 | 37 |
|
||
Transmission mount/case | Upper bellhousing to Engine | 60 | 44 |
|
||
Transmission mount/case | Lower bellhousing to Engine | 40 | 30 |
|
steering torque settings
Save to email ✉️Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
---|---|---|---|---|---|---|
Power steering | Pump to Mounting brackets | 25 | 18 |
|
||
Power steering | Mounting brackets to Cylinder head | 47 | 35 | M8 |
|
|
Power steering | Mounting brackets to Cylinder head | 23 | 17 | M10 |
|
|
Power steering | Power steering pressure transducer | 14 | 10 |
|
exhaust torque settings
Save to email ✉️Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
---|---|---|---|---|---|---|
Exhaust manifold | Exhaust manifold to Cylinder head | 27 | 20 |
|
||
Exhaust manifold | Exhaust manifold heat shield - lower | 20 | 15 |
|
||
Exhaust manifold | Exhaust manifold slip joint stud | 18 | 13 |
|
||
Exhaust manifold | Exhaust manifold slip joint nut | 23 | 17 |
|
brakes torque settings
Save to email ✉️Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to |
---|
suspension torque settings
Save to email ✉️Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to |
---|
general torque settings
Save to email ✉️Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to |
---|
Did you find the answer to your specific question?
👍 1 👎 5