Chevrolet Camaro 6 (2016-2024) Torque Spec Settings
By Kevauto - Own work, CC BY-SA 4.0
Below you'll find the tightening torques for the Chevrolet Camaro 6 in both Nm and ft/lbs. The first table contains the most-used torque settings. The tables after it contain all torque spec values I could find.
Most-used torque specs for Chevrolet Camaro 6
| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
|---|---|---|---|---|---|---|
| Differential | Drain plug | 45 | 33 |
|
|
|
| Wheels | Wheel nuts | 190 | 140 |
|
|
To make sure these are the correct tightening torque values, you can use the data below to verify this is the right model.
Are these torque settings right for you?
- Production years: 2016 - 2024
- Generation: 6
- Type of van: car
- Model variant: Base
- Also known as:
All Torque Settings in Tables
engine torque settings
Save to email ✉️| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
|---|---|---|---|---|---|---|
| Sensor | Transmission speed sensor bolt/screw | 10 | 7 |
|
|
|
| Sensor | Vehicle speed sensor (VSS) bolt | 11 | 8 |
|
|
|
| Sensor | Transmission temperature sensor | 39 | 29 |
|
|
drivetrain torque settings
Save to email ✉️| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
|---|---|---|---|---|---|---|
| Clutch assembly | Clutch housing bolt/screw | 33 | 24 |
|
|
|
| Clutch assembly | Engine to Clutch housing fasteners | 50 | 37 |
|
|
|
| Transmission fluid pan | Transmission oil drain plug | 27 | 20 |
|
|
|
| Transmission fluid pan | Transmission oil fill plug | 27 | 20 |
|
|
|
| Transmission fluid pan | Transmission fluid cooler pipe clip bolt (Pipe retaining points along vehicle) | 9 | 7 | With 1LE package |
|
|
| Transmission fluid pan | Transmission fluid cooler pipe stud (Pipe retaining point) | 22 | 16 | With 1LE package |
|
|
| Transmission mount/case | Transmission control lever knob fastener | 7 | 5 |
|
|
|
| Transmission adapter | Transmission support fasteners | 60 | 44 |
|
|
|
| Transfer | Manual shift detent bolt | 22 | 16 |
|
|
|
| Transfer | Manual transmission selector lever pivot pin (5th gear) | 41 | 30 |
|
|
|
| Transfer | Shift control assembly fasteners | 18 | 13 |
|
|
|
| Transfer | Shift control assembly to Tunnel reinforcement | 12 | 9 |
|
|
|
| Transfer | Shift interlock detent assembly | 40 | 30 |
|
|
|
| Transfer | Shift control shaft position guide bolt/screw | 12 | 9 |
|
|
|
| Transfer | Shift shaft detent plug | 50 | 37 |
|
|
|
| Transfer | Shift shaft detent spring cover bolt | 28 | 21 |
|
|
|
| Transfer | Extension housing bolt/screw | 33 | 24 |
|
|
|
| Drive/Axle shaft | Propeller shaft transmission yoke nut | 140 | 103 |
|
|
steering torque settings
Save to email ✉️| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to |
|---|
exhaust torque settings
Save to email ✉️| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to |
|---|
brakes torque settings
Save to email ✉️| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to |
|---|
suspension torque settings
Save to email ✉️| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to |
|---|
general torque settings
Save to email ✉️| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to |
|---|
By Kevauto - Own work, CC BY-SA 4.0
Did you find the answer to your specific question?
👍 0 👎 0
