Toyota Avalon XX20 (2000-2004) Torque Spec Settings
IFCAR, Public domain, via Wikimedia Commons
Below you'll find the tightening torques for the Toyota Avalon XX20 in both Nm and ft/lbs. The first table contains the most-used torque settings. The tables after it contain all torque spec values I could find.
Most-used torque specs for Toyota Avalon XX20
| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
|---|---|---|---|---|---|---|
| Spark plugs | Spark plugs | 18 | 13 | Use 16mm plug wrench. If there are traces of oil, remove it with gasoline before using the spark plug cleaner. |
|
|
To make sure these are the correct tightening torque values, you can use the data below to verify this is the right model.
Are these torque settings right for you?
- Production years: 2000 - 2004
- Generation: 2
- Type of van: car
- Model variant: Base
All Torque Settings in Tables
engine torque settings
Save to email ✉️| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
|---|---|---|---|---|---|---|
| Oil pan | Drain plug | 49 | 36 |
|
|
|
| Oil pan | Oil pan and gasket | 7.8 | 6 |
|
|
|
| Oil pan | Oil pan to transaxle | 7.8 | 6 | ` |
|
|
| Oil pan | No.1 Oil pan (10mm head) bolt | 8 | 6 | Apply seal packing: Part no. 08826-00080 or equivalent to the oil pan. |
|
|
| Oil pan | No.1 Oil pan (12mm head) bolt | 19.5 | 14 | Apply seal packing: Part no. 08826-00080 or equivalent to the oil pan. |
|
|
| Oil pan | No.1 Oil pan (14mm head) bolt | 37.2 | 27 | Apply seal packing: Part no. 08826-00080 or equivalent to the oil pan. |
|
|
| Oil pan | No. 1 exhaust pipe support bracket | 7.8 | 6 |
|
|
|
| Oil pan | No. 2 Oil pan | 8 | 6 |
|
|
|
| Oil pan | Oil pan baffle plate to No.1 oil pan | 8 | 6 |
|
|
|
| Oil filter | Oil strainer and pipe bracket to valve body (Bolt A) | 10 | 7 |
|
|
|
| Oil filter | Oil strainer and pipe bracket to valve body (Bolt B) | 11 | 8 |
|
|
|
| Oil filter | Oil filter union | 30 | 22 |
|
|
|
| Oil filter | Oil filter drain plug | 45 | 33 |
|
|
|
| Oil pressure switch | Oil pressure switch | 13 | 10 | Apply adhesive: Part no. 08833-00080, THREE BOND 1344, LOCTITE 242 or equivalent. |
|
|
| Oil dipstick | Oil dipstick and guide bolt | 8 | 6 |
|
|
|
| Oil feeder | Oil control valve filter | 45 | 33 |
|
|
|
| Oil feeder | Control valve housing with control valve assembly | 18 | 13 |
|
|
|
| Oil feeder | Self-locking nut | 25 | 18 |
|
|
|
| Oil feeder | Rack housing cap | 59 | 44 | Apply sealant: Part no. 08833-00080, THREE BOND 1344, LOCTITE 242 or equivalent. |
|
|
| Oil feeder | Rack guiding spring cap | 25 | 18 |
|
|
|
| Oil feeder | Rack guiding spring cap lock nut | 50 | 37 | Apply sealant: Part no. 08833-00080, THREE BOND 1344, LOCTITE 242 or equivalent. |
|
|
| Oil feeder | RH and LH claw washers and rack ends | 60 | 44 | Use a torque wrench with a fulcrum length of 345 (13.58 in.). |
|
|
| Oil pump | Oil pump (A bolts) | 19 | 14 |
|
|
|
| Oil pump | Oil pump pickup tube | 13.6 | 10 |
|
|
|
| Oil pump | Oil pump cover | 10.8 | 8 |
|
|
|
| Oil pump | Oil pump (10mm head) bolt | 8 | 6 |
|
|
|
| Oil pump | Oil pump (12mm head) bolt | 19.5 | 14 |
|
|
|
| Piston rods | Connecting rod bolts | 24.5 | 18 | Add 90° |
|
|
| Cylinder head | Cylinder head | 54.2 | 40 | Add 90° |
|
|
| Cylinder head | Cylinder head cover bolts | 8 | 6 | Apply seal packing: Part no. 08826-00080. |
|
|
| Cylinder head | Cylinder head (12 pointed head) bolts | 54 | 40 |
|
|
|
| Cylinder head | Cylinder head (recessed head) bolts | 18.5 | 14 |
|
|
|
| Cylinder head | Cylinder head rear plate | 8 | 6 |
|
|
|
| Cylinder head | Cylinder head rear cover | 10 | 7 |
|
|
|
| Spark plugs | Spark plugs | 18 | 13 | Use 16mm plug wrench. If there are traces of oil, remove it with gasoline before using the spark plug cleaner. |
|
|
| Intake manifold | Intake manifold assembly | 15 | 11 | Perform connecting operations of the fuel tube connector (quick type) after observing the precaution. |
|
|
| Intake manifold | Air intake chamber assembly | 43 | 32 | Use 8 mm hexagon wrench. Install with a new gasket, 2 bolts, and 2 nuts. |
|
|
| Intake manifold | No.2 intake air control valve | 14.5 | 11 | Apply seal packing: Part no. 08826-00080 or equivalent. |
|
|
| Throttle body | No.1 and No.2 Throttle body | 6.9 | 5 |
|
|
|
| Throttle body | Throttle cable from throttle body | 15 | 11 |
|
|
|
| Throttle body | Throttle cable adjusting nut | 15 | 11 |
|
|
|
| Throttle body | Throttle cable retaining plate set bolt | 5.4 | 4 |
|
|
|
| Throttle body | Throttle body bracket bolts | 19.5 | 14 |
|
|
|
| Throttle body | Ground cable and strap with nut | 14.5 | 11 |
|
|
|
| Engine block | Engine hood | 26 | 19 |
|
|
|
| Engine block | Cruise control actuator to body | 13 | 10 |
|
|
|
| Engine block | Oil seal retainer bolts | 8 | 6 |
|
|
|
| Engine block | Cylinder block side cover bolts | 9 | 7 |
|
|
|
| Engine mounts | Engine mounting absorber bolts | 48 | 35 |
|
|
|
| Engine mounts | Front side engine mounting bolts | 44 | 32 |
|
|
|
| Engine mounts | Rear side engine mounting bolt | 66 | 49 |
|
|
|
| Engine mounts | Engine sling device to engine hangers | 20 | 15 | Do not attempt to hang the engine by hooking the chain to any other part. |
|
|
| Engine mounts | Front frame assembly (14 mm head bolt) | 32 | 24 |
|
|
|
| Engine mounts | Front frame assembly (19 mm head bolt) | 181 | 133 |
|
|
|
| Engine mounts | Front frame assembly (nut) | 36 | 27 |
|
|
|
| Engine mounts | RH engine drain plug on cylinder block side cover | 7 | 5 |
|
|
|
| Engine mounts | LH engine drain plug on union | 13 | 10 |
|
|
|
| Engine mounts | Engine moving control rod | 64 | 47 |
|
|
|
| Engine mounts | RH engine mounting bracket | 28 | 21 |
|
|
|
| Engine mounts | No.1 engine hanger bolts | 39 | 29 |
|
|
|
| Engine mounts | Engine hanger to engine | 20 | 15 |
|
|
|
| Engine mounts | Front side engine mounting insulator ot front fram assembly | 80 | 59 |
|
|
|
| Engine mounts | Front engine mounting insulator | 64 | 47 |
|
|
|
| Engine mounts | Rear engine mounting insulator | 66 | 49 |
|
|
|
| Engine mounts | Engine mounting insulator to front frame assembly | 48 | 35 |
|
|
|
| Engine mounts | No.2 RH engine mounting bracket and engine moving control rod (Bolt A, B, C) | 64 | 47 |
|
|
|
| Engine mounts | Front engine mounting insulator (silver bolt) | 44 | 32 |
|
|
|
| Engine mounts | LH mounting insulator | 64 | 47 |
|
|
|
| Engine mounts | Front engine mounting insulator (green bolt) | 66 | 49 |
|
|
|
| Engine mounts | No.2 RH engine mounting bracket and engine moving control rod (Bolt D) | 32 | 24 |
|
|
|
| Sensor | Knock sensor | 39 | 29 |
|
|
|
| Sensor | Speed sensor to axle carrier | 8 | 6 |
|
|
|
| Sensor | Speed sensor to steering knuckle | 8 | 6 |
|
|
|
| Sensor | Speed sensor harness to shock absorber | 5.4 | 4 |
|
|
|
| Sensor | Front speed sensor installation bolt | 8 | 6 |
|
|
|
| Sensor | Rear speed sensor installation bolt | 8 | 6 |
|
|
|
| Sensor | Heater resistance of A/F sensor (Bank 1 sensor 1, Bank 2 sensor 1) | 44 | 32 |
|
|
|
| Sensor | Heater resistance of heated oxygen sensor (Bank 1 sensor 2) | 44 | 32 |
|
|
|
| Sensor | Heated oxygen sensor (Bank 1 sensor 2) | 44 | 32 |
|
|
|
| Sensor | ECT sensor | 20 | 15 | Use 19mm deep socket. |
|
|
| Sensor | Airbag sensor assembly | 20 | 15 | Use torx wrench: T40 (Part no. 09042-00020 or locally manufactured tool). |
|
|
| Sensor | Front airbag sensor LH and RH | 20 | 15 | Connection of the connector is done after the sensor assembly has been installed. The front sensor is equipped with an electrical connection check mechanism. Be sure to lock this mechanism securely when connecting the connector. If the connector is not securely locked, a malfunction code will be detected by the diagnostic system. |
|
|
| Alternator | Rectifier end frame cord clip (Nut A) | 4.5 | 3 |
|
|
|
| Alternator | Rectifier end frame cord clip (Nut B) | 5.4 | 4 |
|
|
|
| Alternator | Rectifier holder to coil lead on rectifier end frame | 2.9 | 2 |
|
|
|
| Alternator | Plate terminal to rectifier holder | 3.9 | 3 |
|
|
|
| Alternator | Voltage regulator and brush holder to rectifier end frame | 2 | 1 | Be careful of the holder installation direction. |
|
|
| Alternator | Rear end cover (Screw) | 3.9 | 3 |
|
|
|
| Alternator | Rear end cover (Nut) | 4.4 | 3 |
|
|
|
| Alternator | Terminal insulator to rectifier holder | 4.1 | 3 |
|
|
|
| Alternator | Drive belt (bolt A) | 29 | 21 | Use a torque wrench with a fulcrum length of 300mm (11.81 in.). |
|
|
| Alternator | Drive belt (bolt B) | 43 | 32 |
|
|
|
| Alternator | Drive belt lock bolt | 18 | 13 |
|
|
|
| Alternator | Drive belt pivot bolt | 56 | 41 |
|
|
|
| Alternator | Generator | 9.8 | 7 |
|
|
|
| Alternator | Generator, bracket, and adjusting bar assembly | 43 | 32 |
|
|
|
| Alternator | Generator to generator bracket | 56 | 41 |
|
|
|
| Alternator | Generator to adjusting bar | 18 | 13 |
|
|
|
| Alternator | Generator pulley to rotor | 110.5 | 82 |
|
|
|
| Alternator | Generator wire to generator | 9.8 | 7 |
|
|
|
| Alternator | No.2 Generator bracket nut | 28 | 21 |
|
|
|
| Alternator | Bearing retainer to drive end frame | 3 | 2 |
|
|
|
| Starter | Starter housing, clutch assembly, and idler gear | 5.9 | 4 |
|
|
|
| Starter | Starter and shift control cable clamp | 39 | 29 |
|
|
|
| Starter | Starter to torque converter clutch housing | 39 | 29 |
|
|
|
| Starter | Shift solenoid valve SL | 6.6 | 5 |
|
|
|
| Starter | Shift solenoid valve SLN | 6.6 | 5 |
|
|
|
| Starter | Solenoid valve No.1 and No.2 | 6.6 | 5 |
|
|
|
| Starter | Field frame | 5.9 | 4 |
|
|
|
| Starter | Armature | 5.9 | 4 |
|
|
|
| Starter | Brush holder | 1.5 | 1 |
|
|
|
| Starter | Magnetic switch terminal kit (terminal nuts) | 17 | 13 |
|
|
|
| Starter | Magnetic switch terminal kit (plunger) | 2.5 | 2 |
|
|
|
| Battery | Ignition coil packs | 6.8 | 5 | Add 90° |
|
|
| Battery | Ignition coil (w/ igniter) | 8 | 6 |
|
|
|
| Camshaft | Camshaft sprocket bolt | 127.4 | 94 |
|
|
|
| Camshaft | Camshaft bearing caps bolts | 16 | 12 |
|
|
|
| Camshaft | Main cap bolts | 21.7 | 16 | Add 90° |
|
|
| Camshaft | Main cap side bolts | 27.1 | 20 |
|
|
|
| Camshaft | RH camshaft timing pulley center bolt | 88 | 65 | Use a torque wrench with a fulcrum length of 340mm (13.39 in.). |
|
|
| Camshaft | LH camshaft timing pulley center bolt | 125 | 92 |
|
|
|
| Camshaft | Exhaust camshaft | 16 | 12 | Apply seal packing: Part no. 08826-00080 or equivalent. |
|
|
| Camshaft | Intake camshaft | 16 | 12 |
|
|
|
| Camshaft | Camshaft position sensor connector | 8 | 6 |
|
|
|
| Camshaft | Camshaft position sensor | 8 | 6 |
|
|
|
| Camshaft | Camshaft timing oil control valves | 7.5 | 6 |
|
|
|
| Crankshaft | Crankshaft position sensor | 8 | 6 |
|
|
|
| Crankshaft | Crankshaft pulley center bolt | 215 | 159 |
|
|
|
| Crankshaft | Crankshaft timing pulley bolt | 8 | 6 | Do not scratch the sensor part of the crankshaft timing pulley. |
|
|
| Crankshaft | Crankshaft main bearing caps (12 pointed head) bolts | 22 | 16 |
|
|
|
| Crankshaft | Crankshaft main bearing caps (hexagon head) bolts | 27 | 20 |
|
|
|
| Common rail | Fuel rail | 10.8 | 8 |
|
|
|
| Water pump | Water pump | 19 | 14 |
|
|
|
| Water pump | Water pump pulley | 19 | 14 |
|
|
|
| Water pump | Water pump | 8 | 6 |
|
|
|
| Water pump | Water inlet housing bolts | 8 | 6 | Apply seal packing: Part no. 08826-00100 or equivalent. |
|
|
| Water pump | Water inlet pipe to cylinder head | 19.5 | 14 |
|
|
|
| Water pump | Water seal plate bolts | 18 | 13 | Apply seal packing: Part no. 08826-00100 or equivalent. |
|
|
| Water pump | Water outlet mounting bolts and nuts | 15 | 11 | Install with 2 bolts, 2 nuts, and 2 plate washers. Alternately tighten the bolts and nuts. Do not scratch the seal surface of the water outlet with the stud bolt. |
|
|
| Fuel/Oil cooler | Oil cooler to lower tank (nuts) | 8.3 | 6 |
|
|
|
| Fuel/Oil cooler | Oil cooler to lower tank (pipe) | 14.7 | 11 |
|
|
|
| Coolant expansion tank | Engine coolant drain union | 39 | 29 | Apply seal packing: Part no. 08826-00100 or equivalent. |
|
|
| Radiator | Engine coolant drain union | 39 | 29 | Apply seal packing: Part no. 08826-00100 or equivalent. |
|
|
| Air conditioning | A/C compressor housing bracket | 25 | 18 |
|
|
|
| Air conditioning | A/C compressor and drive belt adjusting bar bracket (bolt A) | 25 | 18 |
|
|
|
| Air conditioning | A/C compressor and drive belt adjusting bar bracket (bolt B) | 18 | 13 |
|
|
|
| Air conditioning | A/C compressor and drive belt adjusting bar bracket (nut C) | 25 | 18 |
|
|
|
| Air conditioning | Compressor to discharge hose | 10 | 7 |
|
|
|
| Air conditioning | Compressor to suction hose | 10 | 7 |
|
|
|
| Air conditioning | Condenser to discharge hose | 5.4 | 4 |
|
|
|
| Air conditioning | Condenser to liquid tube | 5.4 | 4 |
|
|
|
| Air conditioning | Expansion valve to evaporator | 5.4 | 4 |
|
|
|
| Air conditioning | Compressor to engine | 25 | 18 |
|
|
|
| Air conditioning | Compressor to compressor bracket | 25 | 18 |
|
|
|
| Air conditioning | Pivot bolt | 56 | 41 |
|
|
|
| Air conditioning | Adjusting lock bolt | 18 | 13 |
|
|
|
| Air conditioning | Pressure switch to liquid tube | 10 | 7 |
|
|
|
| Air conditioning | Pressure switch to compressor | 13.2 | 10 |
|
|
|
| Belt tensioner/Timing chains | Timing belt tensioner | 27 | 20 |
|
|
|
| Belt tensioner/Timing chains | No. 1 Timing belt cover | 8.5 | 6 |
|
|
|
| Belt tensioner/Timing chains | No. 2 Timing belt cover | 8.5 | 6 |
|
|
|
| Belt tensioner/Timing chains | No. 3 Timing belt cover | 8.5 | 6 |
|
|
|
| Belt tensioner/Timing chains | Belt tensioner | 24.4 | 18 |
|
|
|
| Belt tensioner/Timing chains | No.1 Idler pulley | 34 | 25 | Use 10mm hexagon wrench to install plate washer and idler pulley with the pivot bolt. Apply adhesive: Part no. 08833-00080, THREE BOND 1344, LOCTITE 242 or equivalent. |
|
|
| Belt tensioner/Timing chains | No.2 Idler pulley | 43 | 32 |
|
|
|
| Belt tensioner/Timing chains | No.2 Idler pulley bracket | 28 | 21 |
|
|
|
| Belt tensioner/Timing chains | Motor mount (Engine side) | 80 | 59 |
|
|
|
| Belt tensioner/Timing chains | Motor mount (Frame side) | 47.5 | 35 |
|
|
|
| Belt tensioner/Timing chains | Pulley | 39 | 29 |
|
|
|
| Valve cover | Valve cover | 12.2 | 9 |
|
|
|
| Fuel system | Fuel inlet pipe | 19 | 14 |
|
|
|
| Fuel system | No.1 Fuel tank protector bolt | 4 | 3 |
|
|
|
| Fuel system | Fuel filter | 2 | 1 |
|
|
|
| Fuel system | Fuel pressure regulator | 2 | 1 |
|
|
|
| Fuel system | Delivery pipes to intake manifold | 10 | 7 |
|
|
|
| Fuel system | No.1 Fuel pipe to intake manifold | 19.5 | 14 |
|
|
|
| Fuel system | Union bolt on the high pressure pipe union | 29 | 21 | Always use 2 new gaskets. Tighten the union bolt by hand. Then, tighten the union bolt to the specified torque. |
|
|
| Fuel system | Flare nut on the high pressure pipe union | 28 | 21 | Apply a light coat of engine oil to the flare nut, and tighten the flare nut by hand. Then, tighten the flare nut to specified torque. Do not rotate the fuel pipe, when tightening the flare nut. Use a torque wrench with a fulcrum length of 30cm (11.81 in.) |
|
|
| Fuel system | No.Fuel pump assembly from fuel tank1 Fuel tank protector bolt | 4 | 3 |
|
|
drivetrain torque settings
Save to email ✉️| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
|---|---|---|---|---|---|---|
| Differential | Transaxle-to-engine bolts | 66 | 49 |
|
|
|
| Differential | Lower transaxle-to-engine bolts | 48 | 35 |
|
|
|
| Differential | Differential fluid drain plug and gasket | 49 | 36 |
|
|
|
| Differential | Left side transaxle mounting nut | 80 | 59 |
|
|
|
| Differential | Transaxle control shaft lever and washer | 15 | 11 |
|
|
|
| Differential | LH transaxle mounting insulator to front frame assembly | 80 | 59 |
|
|
|
| Differential | Oil pipe bracket to transaxle case | 10 | 7 |
|
|
|
| Differential | Line pressure test plug to transaxle case | 7.5 | 6 |
|
|
|
| Differential | Valve body to transaxle case | 11 | 8 |
|
|
|
| Differential | Manual valve body to transaxle case | 11 | 8 |
|
|
|
| Differential | Detent spring to manual valve body | 11 | 8 |
|
|
|
| Differential | Connector clamp to valve body | 6.6 | 5 |
|
|
|
| Wheel hub assembly | Front wheel axle nut | 294.2 | 217 |
|
|
|
| Wheel hub assembly | Front wheel hub | 135.6 | 100 |
|
|
|
| Wheel hub assembly | Rear wheel hub | 80 | 59 |
|
|
|
| Clutch assembly | Converter drain plug | 8.1 | 6 |
|
|
|
| Clutch assembly | Flexplate t oconverter | 40.7 | 30 |
|
|
|
| Clutch assembly | Direct clutch speed sensor to transaxle case | 11 | 8 |
|
|
|
| Clutch assembly | Floor shift lever assembly | 12 | 9 |
|
|
|
| Clutch assembly | Park/Neutral position switch to transaxle case (bolt) | 5.4 | 4 |
|
|
|
| Clutch assembly | Park/Neutral position switch lock plate and nut | 6.9 | 5 |
|
|
|
| Clutch assembly | Drive plate to crankshaft | 83 | 61 | Appy adhesive: Part no. 08833-00070, THREE BOND 1324 or equivalent. |
|
|
| Flywheel | Flywheel to converter | 40.7 | 30 |
|
|
|
| Transmission fluid pan | Transmission pan | 8.1 | 6 |
|
|
|
| Transmission fluid pan | Transmission drain plug | 20.3 | 15 |
|
|
|
| Transmission mount/case | Bell housing bolts | 71.9 | 53 |
|
|
|
| Torque converter | Torque converter drain | 20.3 | 15 |
|
|
|
| Torque converter | Torque converter clutch mouting bolt | 41 | 30 |
|
|
|
| Torque converter | Hole cover to torque converter clutch housing | 41 | 30 |
|
|
|
| Transfer | Transaxle control shaft lever to park/neutral position swithc | 15 | 11 |
|
|
|
| Transfer | Shift control cable to transaxle control shaft lever | 15 | 11 |
|
|
|
| Drive/Axle shaft | Drive shaft lock nut | 294 | 217 |
|
|
|
| Drive/Axle shaft | RH drive shaft to rear side engine mounting insulator | 32 | 24 |
|
|
|
| Brake line | Brake lines to ABS actuator | 15 | 11 |
|
|
|
| Brake line | Brake line union unit (10mm) | 15 | 11 |
|
|
|
| Brake line | Brake line union unit (12mm) | 20 | 15 |
|
|
|
| Tie rod end | Outer tie rod | 48.8 | 36 |
|
|
|
| Tie rod end | Inner tie rod | 67.8 | 50 |
|
|
|
| Tie rod end | Tie rod end to steering knuckle | 49 | 36 |
|
|
|
| Tie rod end | RH and LH tie rod ends and lock nuts | 74 | 55 |
|
|
steering torque settings
Save to email ✉️| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
|---|---|---|---|---|---|---|
| Steering knuckle | Front upper strut nuts | 39.3 | 29 |
|
|
|
| Steering knuckle | Front lower strut nuts | 211.5 | 156 |
|
|
|
| Steering knuckle | Rear strut upper nuts | 33.9 | 25 |
|
|
|
| Steering knuckle | Rear strut lower bolts | 112.5 | 83 |
|
|
|
| Steering rack | Steering gear assembly mounting bolts | 181 | 133 |
|
|
|
| Steering rack | Steering gear housing to front frame assembly | 181 | 133 |
|
|
|
| Steering rack | Front brake caliper installation bolt | 34 | 25 |
|
|
|
| Steering rack | Front brake caliper to flexible hose | 29 | 21 |
|
|
|
| Steering rack | Front brake torque plate to steering knuckle | 107 | 79 |
|
|
|
| Steering rack | Rear brake caliper installation bolt | 34 | 25 |
|
|
|
| Steering rack | Rear brake caliper to flexible hose | 29 | 21 |
|
|
|
| Steering rack | Rear brake torque plate to rear axle carrier | 47 | 35 |
|
|
|
| Steering column | Shift control cable | 15 | 11 |
|
|
|
| Steering column | Universal joint assembly | 35 | 26 |
|
|
|
| Steering column | Steering column assembly | 25 | 18 |
|
|
|
| Steering column | Intermediate shaft assembly (bolt A & B) | 35 | 26 |
|
|
|
| Steering column | Tilt lever lock shaft | 9 | 7 |
|
|
|
| Steering column | Turn signal bracket | 7.5 | 6 |
|
|
|
| Steering column | Shift lever housing | 10 | 7 |
|
|
|
| Steering column | Shift lever | 11 | 8 |
|
|
|
| Steering column | Shift lock solenoid bracket | 3.4 | 3 |
|
|
|
| Steering column | Shift lock switch | 2.8 | 2 |
|
|
|
| Steering wheel | Steering wheel set nut | 50 | 37 |
|
|
|
| Steering wheel | Steering wheel pad | 8.8 | 6 |
|
|
|
| Power steering pump | Power steering to head | 19 | 14 |
|
|
|
| Power steering pump | Power steering to bracket | 40.7 | 30 |
|
|
|
| Power steering pump | Power steering gear assembly set bolt and nuts | 181 | 133 |
|
|
|
| Power steering pump | Power steering pump bracket | 43 | 32 |
|
|
|
| Power steering pump | Power steering pump bolts | 43 | 32 |
|
|
|
| Power steering pump | Power steering vane pump rear housing | 17 | 13 |
|
|
|
| Power steering pump | Power steering vane pump front and rear brackets | 43 | 32 |
|
|
|
| Power steering pump | Power steering vane pump pulley to vane pump shaft | 44 | 32 |
|
|
|
| Power steering pump | Spring, flow control valve, and pressure port union | 83 | 61 |
|
|
|
| Power steering pump | Power steering reservoir pipe mounting brackets | 10 | 7 |
|
|
|
| Power steering pump | Power steering reservoir pipe to front frame | 10 | 7 |
|
|
|
| Power steering pump | Power steering pressure tube | 39 | 29 |
|
|
|
| Power steering pump | 2-turn pressure tubes | 12 | 9 |
|
|
|
| Power steering pump | Pressure feed tube to power steering vane pump assembly (union bolt) | 52 | 38 |
|
|
|
| Power steering pump | Pressure feed and return tube | 28 | 21 | Use a torque wrench with a fulcrum length of 300mm (11.81 in.). |
|
|
| Power steering pump | Clamp plate | 10 | 7 |
|
|
|
| Power steering pump | Torque steering wheel set nut | 50 | 37 |
|
|
|
| Power steering pump | Adjusting strut and power steering pump drive belt | 43.1 | 32 |
|
|
exhaust torque settings
Save to email ✉️| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
|---|---|---|---|---|---|---|
| Exhaust manifold | RH exhaust manifold | 49 | 36 |
|
|
|
| Exhaust manifold | LH exhaust manifold | 49 | 36 |
|
|
|
| Exhaust manifold | Exhaust manifold stay | 34 | 25 |
|
|
|
| Exhaust manifold | Exhaust manifold to front exhaust pipe | 62 | 46 |
|
|
|
| Exhaust manifold | Front exhaust pipe to center exhaust pipe | 43 | 32 | 2 bolts and 2 compression springs. |
|
|
| Exhaust manifold | Front exhaust pipe support stay to fron exhaust pipe support bracket | 33 | 24 |
|
|
|
| Exhaust manifold | Exhaust manifold bracket mounting bolt | 34 | 25 |
|
|
|
| Exhaust manifold | Exhaust manifold bracket to transaxle case | 20 | 15 |
|
|
|
| Exhaust manifold | Exhaust manifold plate | 34 | 25 |
|
|
|
| EGR | Exhaust EGR pipe | 19 | 14 |
|
|
brakes torque settings
Save to email ✉️| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
|---|---|---|---|---|---|---|
| Disc brake | Brake caliper bracket (front wheel hub) | 107.1 | 79 |
|
|
|
| Disc brake | Front caliper banjo bolt | 29.8 | 22 |
|
|
|
| Disc brake | Rear caliper banjo bolt | 29.8 | 22 |
|
|
|
| Disc brake | Caliper installation bolts | 34 | 25 |
|
|
|
| Disc brake | Rear lugnut | 149.1 | 110 |
|
|
|
| Disc brake | Bleeder plug | 8.3 | 6 |
|
|
|
| Disc brake | Torque plate | 107 | 79 |
|
|
|
| Disc brake | Torque plate mounting bolts | 47 | 35 |
|
|
|
| Disc brake | Rear disc brake assembly mounting bolts | 47 | 35 |
|
|
|
| Disc brake | Disc hub | 103 | 76 |
|
|
|
| Brake booster | Brake booster installation nuts | 13 | 10 |
|
|
|
| Brake pedal | Brake booster installation nuts | 13 | 10 |
|
|
|
| Brake pedal | Brake pedal to pedal bracket | 39 | 29 |
|
|
|
| Brake pedal | Brake pedal bracket | 5 | 4 |
|
|
|
| Master cylinder | Master cylinder to brake booster assembly | 13 | 10 |
|
|
|
| Master cylinder | Master cylinder pressure sensor | 81 | 60 |
|
|
|
| Master cylinder | Master cylinder to piston stopper bolt | 10 | 7 |
|
|
|
| Master cylinder | Master cylinder to reservoir | 1.7 | 1 |
|
|
|
| Parking brake | Parking brake pedal assembly nuts | 61 | 45 |
|
|
|
| Parking brake | Adjusting hexagon lock nut | 5.4 | 4 |
|
|
|
| ABS | ABS actuator assembly | 19 | 14 |
|
|
|
| ABS | ABS actuator to ABS actuator bracket | 13 | 10 |
|
|
|
| ABS | ABS actuator to ECU | 3 | 2 |
|
|
|
| ABS | ABS & VSC actuator to actuator bracket | 13 | 10 |
|
|
|
| ABS | ABS & VSC actuator brakcet to body | 19 | 14 |
|
|
|
| ABS | ABS speed sensor harness clamp bolt | 5.4 | 4 |
|
|
|
| ABS | Precharge pump assembly | 19 | 14 |
|
|
|
| ABS | Precharge pump to brake lines (10mm nut) | 15 | 11 |
|
|
|
| ABS | Precharge pump to brake lines (12mm nut) | 20 | 15 |
|
|
|
| ABS | Precharge pump bracket (Nut) | 13 | 10 |
|
|
|
| ABS | Precharge pump bracket (Bolt) | 8 | 6 |
|
|
|
| ABS | Precharge pump to master cylinder pressure sensor | 81 | 60 |
|
|
suspension torque settings
Save to email ✉️| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
|---|---|---|---|---|---|---|
| Wheels | LH and RH front wheels | 103 | 76 |
|
|
|
| Wheels | Rear wheel | 103 | 76 |
|
|
|
| Wheels | Flexible hose to caliper | 29 | 21 |
|
|
|
| Shock absorbers/shocks | Flexible hose to shock absorber bracket | 29 | 21 |
|
|
|
| Stabilizer bar | Front stabilizer bar | 19 | 14 |
|
|
|
| Stabilizer bar | Stabilizer bar bracket to front frame assembly | 19 | 14 |
|
|
|
| Sway bar links/Stabilizer links | Stablilizer bar link to stabilizer bar | 39 | 29 |
|
|
|
| Sway bar links/Stabilizer links | Stabilizer frame bolt | 25.8 | 19 |
|
|
|
| Sway bar links/Stabilizer links | Front stabilizer endlink | 39.3 | 29 |
|
|
|
| Sway bar links/Stabilizer links | Front swaybar bracket | 25.8 | 19 |
|
|
|
| Sway bar links/Stabilizer links | Front swaybar endlinks | 39.3 | 29 |
|
|
|
| Sway bar links/Stabilizer links | Rear swaybar endlinks | 39.3 | 29 |
|
|
|
| Sway bar links/Stabilizer links | Rear stabilizer links | 39.3 | 29 |
|
|
|
| Control arm | Front lower arm frame bolts | 203.4 | 150 |
|
|
|
| Control arm | Front lower arm to ball joint | 127.4 | 94 |
|
|
|
| Control arm | Lower suspension arm to lower ball joint | 127 | 94 |
|
|
|
| Control arm | Rear control arm | 183 | 135 |
|
|
|
| Ball joint | Front lower ball joint to knuckle | 122 | 90 |
|
|
|
| Ball joint | Front lower ball joint to arm | 74.6 | 55 |
|
|
|
| Ball joint | Front lower ball joint nut | 122 | 90 |
|
|
general torque settings
Save to email ✉️| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to |
|---|
Kevauto, CC BY-SA 4.0, via Wikimedia Commons
Did you find the answer to your specific question?
👍 2 👎 1
