Toyota Yaris XP90 (2005-2012) Torque Spec Settings
By M 93 - Own work, CC BY-SA 3.0 de
Below you'll find the tightening torques for the Toyota Yaris XP90 in both Nm and ft/lbs. The first table contains the most-used torque settings. The tables after it contain all torque spec values I could find.
Most-used torque specs for Toyota Yaris XP90
| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
|---|---|---|---|---|---|---|
| Oil pan | Oil pan drain plug | 38 | 28 |
|
|
|
| Wheels | Front wheel | 103 | 76 |
|
|
|
| Wheels | Rear wheel | 103 | 76 |
|
|
To make sure these are the correct tightening torque values, you can use the data below to verify this is the right model.
Are these torque settings right for you?
- Production years: 2005 - 2012
- Generation: 2
- Type of van: car
- Model variant: Base
- Also known as:
All Torque Settings in Tables
engine torque settings
Save to email ✉️| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
|---|---|---|---|---|---|---|
| Oil pan | Oil pan drain plug | 38 | 28 |
|
|
|
| Oil pan | Oil pan sub-assembly stud bolt | 5 | 4 |
|
|
|
| Oil pan | Cylinder block assembly to Oil pan sub-assembly | 24 | 18 |
|
|
|
| Oil pan | Oil pan sub-assembly to Oil pan sub-assembly No.2 | 9 | 7 |
|
|
|
| Oil filter | Oil filter sub-assembly | 13 | 10 |
|
|
|
| Oil filter | Oil pan sub-assembly to Oil filter union | 30 | 22 |
|
|
|
| Oil filter | Oil pan sub-assembly to Oil strainer | 11 | 8 |
|
|
|
| Oil pressure switch | Oil pressure switch to Cylinder block assembly | 15 | 11 |
|
|
|
| Oil pump | Oil pump assembly to Cylinder head and block | 32 | 24 | Bolt A |
|
|
| Oil pump | Oil pump assembly to Cylinder head and block | 11 | 8 | Bolt B |
|
|
| Oil pump | Oil pump assembly to Cylinder head and block | 11 | 8 | Bolt C |
|
|
| Oil pump | Oil pump assembly to Cylinder head and block | 24 | 18 | Nut D |
|
|
| Oil pump | Oil pump assembly to Cylinder head and block | 24 | 18 | Bolt E |
|
|
| Oil pump | Oil pump assembly to Transaxle housing | 22 | 16 |
|
|
|
| Oil pump | Fan belt adjusting bar to Oil pump assembly | 11 | 8 |
|
|
|
| Oil pump | Screw plug to Oil pump assembly | 5 | 4 |
|
|
|
| Oil pump | Stator shaft assembly to Front oil pump body | 10 | 7 |
|
|
|
| Oil pump | Oil pump cover to Oil pump assembly bolt | 9 | 7 |
|
|
|
| Oil pump | Oil pump cover to Oil pump assembly screw | 10 | 7 |
|
|
|
| Oil pump | Oil pump cover to Oil pump relief valve plug | 25 | 18 |
|
|
|
| Piston rods | Connecting rod assembly to Connecting rod cap | 15 | 11 |
|
|
|
| Cylinder head | Cylinder head assembly to Cylinder block assembly | 29 | 21 | Step 1 |
|
|
| Cylinder head | Cylinder head assembly stud bolt | 10 | 7 | Bolt A |
|
|
| Cylinder head | Cylinder head assembly stud bolt | 10 | 7 | Bolt B |
|
|
| Cylinder head | Cylinder head assembly stud bolt | 10 | 7 | Bolt C |
|
|
| Cylinder head | Cylinder head assembly stud bolt | 9 | 7 | Bolt D |
|
|
| Cylinder head | Cylinder head assembly to Harness bracket | 13 | 10 |
|
|
|
| Cylinder head | Cylinder head cover sub-assembly to Cylinder head assembly | 10 | 7 |
|
|
|
| Cylinder head | Cylinder head cover No.2 to Cylinder head cover | 7 | 5 |
|
|
|
| Cylinder head | Ventilation valve sub-assembly to Cylinder head cover sub-assembly | 27 | 20 |
|
|
|
| Spark plugs | Spark plugs to Cylinder head assembly | 18 | 13 |
|
|
|
| Intake manifold | Intake manifold to Cylinder block assembly | 30 | 22 |
|
|
|
| Throttle body | Throttle with motor body assembly to Intake manifold | 9 | 7 |
|
|
|
| Throttle body | Water filler sub-assembly to Throttle with motor body assembly | 8 | 6 |
|
|
|
| Throttle body | Throttle with motor body assembly to Wire harness with bracket | 9 | 7 |
|
|
|
| Engine block | Cylinder block assembly stud bolt | 5 | 4 | Bolt A |
|
|
| Engine block | Cylinder block assembly stud bolt | 5 | 4 | Bolt B |
|
|
| Engine block | Cylinder block assembly stud bolt | 11 | 8 | Bolt C |
|
|
| Engine block | Cylinder block assembly stud bolt | 5 | 4 | Bolt D |
|
|
| Engine block | Water inlet to Cylinder block assembly | 9 | 7 |
|
|
|
| Engine mounts | Transverse engine mounting bracket to Cylinder head and block | 55 | 41 |
|
|
|
| Engine mounts | Transverse engine mounting bracket to Transmission case cover | 64 | 47 |
|
|
|
| Engine mounts | Transverse engine mounting insulator to Body | 52 | 38 |
|
|
|
| Engine mounts | Transverse engine mounting control bracket to Transaxle case | 39 | 29 |
|
|
|
| Engine mounts | Engine mounting bracket LH to Automatic transaxle | 64 | 47 |
|
|
|
| Engine mounts | Engine mounting insulator RH to Body | 45 | 33 | Bolt A |
|
|
| Engine mounts | Engine mounting insulator RH to Body | 52 | 38 | Bolt B |
|
|
| Engine mounts | Engine mounting insulator RH to Body | 52 | 38 |
|
|
|
| Engine mounts | Engine mounting insulator LH to Engine mounting bracket LH | 52 | 38 |
|
|
|
| Engine mounts | Engine mounting insulator LH to Engine mounting bracket LH | 52 | 38 |
|
|
|
| Engine mounts | Front suspension crossmember sub-assembly to Engine moving control rod | 120 | 89 |
|
|
|
| Sensor | Air fuel ratio sensor to Exhaust manifold assembly | 44 | 32 |
|
|
|
| Sensor | Heated oxygen sensor to Front exhaust pipe | 44 | 32 |
|
|
|
| Sensor | Heated oxygen sensor (for sensor 2) to Exhaust front pipe assembly | 44 | 32 |
|
|
|
| Sensor | Camshaft position sensor to Cylinder head assembly | 8 | 6 |
|
|
|
| Sensor | Crankshaft position sensor to Oil pump assembly | 8 | 6 |
|
|
|
| Sensor | Engine coolant temperature sensor to Cylinder head assembly | 20 | 15 |
|
|
|
| Sensor | Knock sensor to Cylinder block assembly | 20 | 15 |
|
|
|
| Sensor | Front speed sensor to Steering knuckle | 9 | 7 |
|
|
|
| Sensor | Front speed sensor to Front flexible hose | 29 | 21 |
|
|
|
| Sensor | Front speed sensor to Body | 6 | 4 |
|
|
|
| Sensor | Speedometer sensor to Automatic transaxle | 7 | 5 |
|
|
|
| Sensor | Transmission revolution sensor to Automatic transaxle | 5 | 4 |
|
|
|
| Alternator | Generator assembly to Wire harness clamp | 10 | 7 |
|
|
|
| Alternator | Generator assembly to Cylinder block sub-assembly | 54 | 40 |
|
|
|
| Alternator | Generator assembly to Fan belt adjusting slide | 19 | 14 |
|
|
|
| Alternator | Generator pulley to Generator rotor assembly | 133 | 98 |
|
|
|
| Alternator | Generator brush holder assembly to Generator holder with rectifier | 2 | 1 |
|
|
|
| Alternator | Rear end cover to Generator rectifier end frame | 4 | 3 |
|
|
|
| Alternator | Terminal insulator to enerator regulator assembly | 4 | 3 |
|
|
|
| Alternator | Generator regulator assembly to Generator rectifier end frame | 2 | 1 |
|
|
|
| Alternator | Generator holder with rectifier to Generator rectifier end frame | 2 | 1 |
|
|
|
| Alternator | Generator holder with rectifier to Generator rectifier end frame | 5 | 4 |
|
|
|
| Starter | Starter assembly to Transaxle housing | 37 | 27 | For 0.8kW type |
|
|
| Starter | Starter assembly to Transaxle housing | 37 | 27 | For 1.6kW type |
|
|
| Starter | Starter assembly to Terminal 30 | 10 | 7 | For 0.8kW type |
|
|
| Starter | Starter assembly to Terminal 30 | 10 | 7 | For 1.6kW type |
|
|
| Starter | Starter brush holder assembly to Commutator end frame | 2 | 1 | For 0.8kW type |
|
|
| Starter | Starter yoke assembly to Commutator end frame | 6 | 4 | For 0.8kW type |
|
|
| Starter | Starter yoke assembly to Starter commutator end frame assembly | 6 | 4 | For 1.6kW type |
|
|
| Starter | Magnet starter switch assembly to Starter housing | 8 | 6 | For 0.8kW type |
|
|
| Starter | Magnet switch body to Starter drive housing assembly | 8 | 6 | For 1.6kW type |
|
|
| Battery | Battery to Battery clamp | 4 | 3 |
|
|
|
| Battery | Battery carrier to Body | 17 | 13 |
|
|
|
| Battery | Battery terminal to Cable | 5 | 4 |
|
|
|
| Battery | Battery negative terminal to Battery negative cable | 5 | 4 |
|
|
|
| Battery | Ignition coil to Cylinder head cover | 9 | 7 |
|
|
|
| Camshaft | Camshaft bearing cap No.1 to Cylinder head assembly | 23 | 17 |
|
|
|
| Camshaft | Camshaft bearing cap No.2 to Cylinder head assembly | 13 | 10 |
|
|
|
| Camshaft | Camshaft No.2 to Camshaft timing sprocket | 64 | 47 |
|
|
|
| Camshaft | Camshaft timing gear assembly to Camshaft | 64 | 47 |
|
|
|
| Camshaft | Camshaft timing oil control valve assembly to Cylinder head assembly | 8 | 6 |
|
|
|
| Crankshaft | Cylinder block assembly to Crankshaft bearing cap | 22 | 16 |
|
|
|
| Crankshaft | Crankshaft damper sub-assembly to Crankshaft | 128 | 94 |
|
|
|
| Crankshaft | Chain vibration damper No.1 to Cylinder head and block | 9 | 7 |
|
|
|
| Water pump | Water pump assembly to Oil pump assembly | 11 | 8 |
|
|
|
| Water pump | Water pump pulley to Water pump assembly | 15 | 11 |
|
|
|
| Fuel/Oil cooler | Inlet No.1 oil cooler tube to Automatic transaxle | 34 | 25 |
|
|
|
| Fuel/Oil cooler | Outlet No.1 oil cooler tube to Automatic transaxle | 34 | 25 |
|
|
|
| Fuel/Oil cooler | No.2 oil cooler tube clamp to Transmission oil filler tube sub-assembly | 6 | 4 |
|
|
|
| Fuel/Oil cooler | Oil cooler tube union to Automatic transaxle | 27 | 20 |
|
|
|
| Radiator | Radiator support sub-assembly upper to Body | 6 | 4 |
|
|
|
| Radiator | Water filler sub-assembly to Radiator sub-assembly | 8 | 6 |
|
|
|
| Radiator | Water inlet to Radiator hose | 9 | 7 |
|
|
|
| Radiator | Cooling fan resistor to Body | 5 | 4 |
|
|
|
| Air conditioning | Air conditioning unit to Body | 10 | 7 |
|
|
|
| Air conditioning | Air conditioning unit to Instrument panel reinforcement | 4 | 3 |
|
|
|
| Air conditioning | Compressor and pulley to Oil pan sub-assembly | 25 | 18 |
|
|
|
| Air conditioning | No.1 cooler refrigerant discharge hose to Compressor and pulley | 10 | 7 |
|
|
|
| Air conditioning | No.1 cooler refrigerant suction hose to Compressor and pulley | 10 | 7 |
|
|
|
| Air conditioning | Cooler expansion valve to No.1 cooler evaporator sub-assembly | 4 | 3 |
|
|
|
| Air conditioning | Suction tube and liquid tube to Cooler expansion valve | 10 | 7 |
|
|
|
| Air conditioning | Cooler dryer to Condenser | 3 | 2 |
|
|
|
| Air conditioning | Liquid tube assembly A to Condenser | 5 | 4 |
|
|
|
| Air conditioning | No.1 cooler discharge hose to Condenser | 5 | 4 |
|
|
|
| Belt tensioner/Timing chains | Chain tensioner slipper to Cylinder block assembly | 9 | 7 |
|
|
|
| Belt tensioner/Timing chains | Cylinder block assembly to Chain tensioner assembly No.1 | 9 | 7 |
|
|
|
| PCM | ECM to Body | 8 | 6 |
|
|
|
| Fuel system | Fuel delivery pipe subassembly to Cylinder head assembly bolt | 19 | 14 | Bolt A |
|
|
| Fuel system | Fuel delivery pipe subassembly to Cylinder head assembly bolt | 9 | 7 | Bolt B |
|
|
| Fuel system | Fuel tank assembly to Floor panel | 14 | 10 |
|
|
|
| Fuel system | Fuel tank cover vent case sub-assembly to Floor panel | 5 | 4 |
|
|
drivetrain torque settings
Save to email ✉️| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
|---|---|---|---|---|---|---|
| Differential | Differential case to Front differential ring gear | 88 | 65 |
|
|
|
| Differential | Front differential ring gear to Front differential case | 77 | 57 |
|
|
|
| Wheel hub assembly | Wheel hub bearing fasteners | 90 | 66 | Use a drive socket #14. Use a torque wrench. |
|
|
| Wheel hub assembly | Front wheel hub nut | 103 | 76 |
|
|
|
| Wheel hub assembly | Front axle hub nut to Front drive shaft | 216 | 159 |
|
|
|
| Wheel hub assembly | Rear axle hub and bearing assembly to Rear axle beam | 90 | 66 |
|
|
|
| Clutch assembly | Clutch pedal stopper bolt to Lock nut | 16 | 12 |
|
|
|
| Clutch assembly | Clutch pedal sub-assembly to Clutch pedal support | 37 | 27 |
|
|
|
| Clutch assembly | Clutch pedal support to Body | 24 | 18 |
|
|
|
| Clutch assembly | Clutch switch assembly to Clutch pedal | 16 | 12 |
|
|
|
| Clutch assembly | Clutch master cylinder to Clutch pedal support | 9 | 7 |
|
|
|
| Clutch assembly | Clutch master cylinder push rod clevis lock nut | 12 | 9 |
|
|
|
| Clutch assembly | Clutch master cylinder to flexible hose tube to Clutch master cylinder | 15 | 11 |
|
|
|
| Clutch assembly | Clutch release cylinder to Manual transaxle case | 12 | 9 |
|
|
|
| Clutch assembly | Release cylinder bleeder plug to Clutch release cylinder | 8 | 6 |
|
|
|
| Clutch assembly | Clutch release cylinder to flexible hose tube to Clutch release cylinder | 15 | 11 |
|
|
|
| Clutch assembly | Release fork support to Manual transaxle | 37 | 27 |
|
|
|
| Flywheel/Flex plate | Flywheel sub-assembly to Crankshaft | 49 | 36 | Step 1 |
|
|
| Flywheel/Flex plate | Clutch cover assembly to Flywheel sub-assembly | 19 | 14 |
|
|
|
| Flywheel/Flex plate | Drive plate and torque converter clutch setting bolt to Drive plate and ring gear sub-assembly | 27 | 20 |
|
|
|
| Flywheel/Flex plate | Drive plate and ring gear sub-assembly to Crankshaft | 88 | 65 |
|
|
|
| Transmission fluid pan | Drain plug to Automatic transaxle oil pan sub-assembly | 49 | 36 |
|
|
|
| Transmission fluid pan | Filler plug to Manual transmission case | 39 | 29 |
|
|
|
| Transmission fluid pan | Automatic transaxle oil pan sub-assembly to Automatic transaxle case | 8 | 6 |
|
|
|
| Transmission fluid pan | Transmission oil filler tube sub-assembly to Automatic transaxle | 6 | 4 |
|
|
|
| Transmission mount/case | Automatic transaxle assembly to Engine block sub-assembly | 30 | 22 |
|
|
|
| Transmission mount/case | Automatic transaxle assembly to Engine | 30 | 22 |
|
|
|
| Transmission mount/case | Manual transaxle assembly to Engine | 33 | 24 |
|
|
|
| Transmission mount/case | Transaxle housing to Transaxle case | 29 | 21 | Bolt A |
|
|
| Transmission mount/case | Transaxle housing to Transaxle case | 22 | 16 | Bolt B |
|
|
| Transmission mount/case | Bearing lock plate to Transaxle housing | 11 | 8 |
|
|
|
| Transmission mount/case | Bearing lock plate to Transaxle case | 11 | 8 |
|
|
|
| Transmission mount/case | Transmission wire to Automatic transaxle case | 5 | 4 |
|
|
|
| Transmission mount/case | Transmission valve body assembly to Automatic transaxle | 11 | 8 |
|
|
|
| Transmission mount/case | Manual detent spring sub-assembly to Transmission valve body assembly | 11 | 8 |
|
|
|
| Transmission mount/case | Valve body oil strainer sub-assembly to Automatic transaxle case | 8 | 6 |
|
|
|
| Transmission mount/case | No.1 transaxle case plug to Automatic transaxle | 7 | 5 |
|
|
|
| Transmission mount/case | Screw plug to Automatic transaxle | 7 | 5 |
|
|
|
| Transmission mount/case | Rear transaxle cover assembly to Transaxle case | 25 | 18 |
|
|
|
| Transmission mount/case | Transmission case cover to Transmission case | 18 | 13 |
|
|
|
| Transmission mount/case | Rear transaxle cover plug to Rear transaxle cover | 7 | 5 |
|
|
|
| Transmission mount/case | Transaxle case receiver to Transaxle case | 11 | 8 |
|
|
|
| Transmission mount/case | Transmission output shaft rear set nut to Output saft | 118 | 87 |
|
|
|
| Torque converter | Torque converter set bolt to Drive plate | 27 | 20 |
|
|
|
| Transfer | Parking lock pawl bracke to Transaxle case | 20 | 15 |
|
|
|
| Transfer | Park/Neutral position switch assembly to Automatic transaxle | 5 | 4 |
|
|
|
| Transfer | Lock plate to Park/Neutral position switch assembly | 7 | 5 |
|
|
|
| Transfer | Control shaft lever to Park/Neutral position switch assembly | 13 | 10 |
|
|
|
| Transfer | Control shaft cover to Transmission case | 20 | 15 |
|
|
|
| Transfer | Transmission control cable assembly to Control shaft lever | 12 | 9 |
|
|
|
| Transfer | Transmission control cable assembly to Body | 5 | 4 |
|
|
|
| Transfer | Transmission control cable to Body | 5 | 4 |
|
|
|
| Transfer | No.1 transmission control cable bracket to Automatic transaxle | 12 | 9 |
|
|
|
| Transfer | Control cable bracket to Transaxle case | 25 | 18 |
|
|
|
| Transfer | Floor shift assembly to Body | 12 | 9 |
|
|
|
| Transfer | Floor shift lever assembly to Body | 12 | 9 |
|
|
|
| Transfer | Gear shift fork No.1 to Gear shift fork shaft No.1 | 16 | 12 |
|
|
|
| Transfer | Gear shift fork No.2 to Gear shift fork shaft No.2 | 16 | 12 |
|
|
|
| Transfer | Gear shift fork No.3 to Gear shift fork shaft No.3 | 16 | 12 |
|
|
|
| Transfer | Gear shift head No.1 to Gear shift fork shaft No.2 | 16 | 12 |
|
|
|
| Transfer | Shift solenoid valve to Valve body | 11 | 8 |
|
|
|
| Drive/Axle shaft | Drive shaft nut | 216 | 159 | Use a 12-point socker No.30. Use a torque wrench. |
|
|
| Drive/Axle shaft | Drive shaft nut | 216 | 159 | Use a 12-point socker No.30. Use a torque wrench. |
|
|
| Drive/Axle shaft | Drive shaft heat insulator sub-assembly to Cylinder block sub-assembly | 18 | 13 |
|
|
|
| Drive/Axle shaft | Rear axle beam to Body | 90 | 66 |
|
|
steering torque settings
Save to email ✉️| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
|---|---|---|---|---|---|---|
| Tie rod end | Tie rod end sub-assembly to Steering knuckle | 49 | 36 |
|
|
|
| Tie rod end | Tie rod end lock nut | 75 | 55 |
|
|
|
| Steering rack | Steering sliding yoke sub-assembly to Steering gear assembly | 28 | 21 |
|
|
|
| Steering column | Steering column to Instrument panel reinforcement assembly | 25 | 18 |
|
|
|
| Steering shaft | Steering sliding yoke sub-assembly to Steering intermediate shaft assembly No.2 | 28 | 21 |
|
|
|
| Steering shaft | Steering intermediate shaft assembly No.2 to Steering column assembly | 28 | 21 |
|
|
|
| Steering wheel | Steering wheel assembly to Steering column assembly | 50 | 37 |
|
|
|
| Steering wheel | Steering pad to Steering wheel assembly | 9 | 7 |
|
|
|
| Steering wheel | Steering pad to Steering wheel assembly | 9 | 7 |
|
|
|
| Power steering | Power steering gear to Front suspension crossmember sub-assembly | 96 | 71 |
|
|
|
| Power steering | Steering sliding yoke sub-assembly to Power steering gear | 28 | 21 |
|
|
|
| Power steering | Power steering ECU to Instrument panel reinforcement assembly | 5 | 4 |
|
|
exhaust torque settings
Save to email ✉️| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
|---|---|---|---|---|---|---|
| Exhaust manifold | Exhaust manifold to Cylinder head assembly | 27 | 20 |
|
|
|
| Exhaust manifold | Exhaust manifold heat insulator No.1 to Exhaust manifold | 8 | 6 |
|
|
|
| Exhaust manifold | Manifold support bracket to Cylinder block and exhaust manifold | 44 | 32 |
|
|
|
| Exhaust manifold | Exhaust front pipe assembly to Exhaust manifold | 43 | 32 |
|
|
brakes torque settings
Save to email ✉️| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
|---|---|---|---|---|---|---|
| Disc brake | Front disc brake cylinder mounting to Steering knuckle | 107 | 79 |
|
|
|
| Disc brake | Disc brake cylinder assembly to Front disc brake cylinder mounting | 34 | 25 |
|
|
|
| Disc brake | Rear wheel brake cylinder assembly to Backing plate | 10 | 7 |
|
|
|
| Disc brake | Front disc brake bleeder plug to Disc brake cylinder assembly | 8 | 6 |
|
|
|
| Disc brake | Rear drum brake bleeder plug to Rear wheel brake cylinder assembly | 8 | 6 |
|
|
|
| Disc brake | Front flexible hose to Disc brake cylinder assembly | 30 | 22 |
|
|
|
| Disc brake | Brake tube to Rear wheel brake cylinder assembly | 14 | 10 |
|
|
|
| Disc brake | Brake tube to Rear wheel brake cylinder assembly | 15 | 11 | For use without SST |
|
|
| Disc brake | Brake caliper fasteners | 34 | 25 | Use HEX No.H7. Use a torque wrench. |
|
|
| Disc brake | Brake caliper fasteners | 34 | 25 | Use HEX No.H7. Use a torque wrench. |
|
|
| Disc brake | Brake actuator to Body | 19 | 14 |
|
|
|
| Disc brake | Brake actuator bracket assembly to Brake actuator | 5 | 4 |
|
|
|
| Brake line | Rear brake tube to Rear axle beam | 5 | 4 |
|
|
|
| Brake line | Brake tube to Brake actuator | 14 | 10 |
|
|
|
| Brake line | Brake tube to Brake actuator | 15 | 11 | For use without SST |
|
|
| Brake line | Brake tube to Brake master cylinder | 14 | 10 |
|
|
|
| Brake line | Brake tube to Brake master cylinder | 15 | 11 | For use without SST |
|
|
| Brake line | Brake tube to Brake tube way | 14 | 10 |
|
|
|
| Brake line | Brake tube to Brake tube way | 15 | 11 | For use without SST |
|
|
| Brake line | Brake tube to Front flexible hose | 14 | 10 |
|
|
|
| Brake line | Brake tube to Front flexible hose | 15 | 11 | For use without SST |
|
|
| Brake line | Rear flexible hose to Rear brake tube | 14 | 10 |
|
|
|
| Brake line | Rear flexible hose to Rear brake tube | 15 | 11 | For use without SST |
|
|
| Brake line | Brake tube to Proportioning valve | 14 | 10 |
|
|
|
| Brake line | Brake tube to Proportioning valve | 15 | 11 | For use without SST |
|
|
| Brake booster | Push rod lock nut to Brake booster push rod | 26 | 19 |
|
|
|
| Brake booster | Brake pedal support to Brake booster | 9 | 7 |
|
|
|
| Brake pedal | Brake pedal to Brake pedal support | 37 | 27 |
|
|
|
| Brake pedal | Brake pedal support to Instrument panel reinforcement assembly | 24 | 18 |
|
|
|
| Brake pedal | Accelerator pedal assembly to Body | 5 | 4 |
|
|
|
| Master cylinder | Brake master cylinder to Brake booster | 13 | 10 |
|
|
|
| Master cylinder | Piston stopper bolt to Master cylinder body | 10 | 7 |
|
|
|
| Parking brake | Lock nut to Parking brake pull rod sub-assembly | 5 | 4 |
|
|
|
| Parking brake | Parking brake switch to Parking brake lever | 1 | 1 |
|
|
|
| Parking brake | Parking brake lever to Body | 13 | 10 |
|
|
|
| Parking brake | Parking brake cable | 6 | 4 |
|
|
|
| Parking brake | Parking brake cable to Backing plate | 8 | 6 |
|
|
|
| Parking brake | Parking brake cable to Rear axle beam | 6 | 4 |
|
|
|
| ABS | ABS sensor fastener to steering knuckle | 8 | 6 | Use a drive socket #10. Use a torque wrench. |
|
|
| ABS | ABS sensor fastener to steering knuckle | 8 | 6 | Use a drive socket #10. Use a torque wrench. |
|
|
suspension torque settings
Save to email ✉️| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
|---|---|---|---|---|---|---|
| Wheels | Front wheel | 103 | 76 |
|
|
|
| Wheels | Rear wheel | 103 | 76 |
|
|
|
| Struts | Shock strut lower fastener to steering knuckle | 164 | 121 | Use a combination spanner #19. Use a drive socket #19. Use a torque wrench. |
|
|
| Shock absorbers/shocks | Front shock absorber assembly to Steering knuckle | 164 | 121 |
|
|
|
| Shock absorbers/shocks | Rear shock absorber to Rear axle beam | 49 | 36 |
|
|
|
| Shock absorbers/shocks | Front support to front shock absorber nut to Front shock absorber assembly | 33 | 24 |
|
|
|
| Shock absorbers/shocks | Rear support to rear shock absorber nut to Rear shock absorber | 25 | 18 |
|
|
|
| Shock absorbers/shocks | Front flexible hose to Front shock absorber assembly | 29 | 21 |
|
|
|
| Shock absorbers/shocks | Front shock absorber with coil spring to Body | 55 | 41 |
|
|
|
| Stabilizer bar | Front stabilizer bracket to Front suspension crossmember sub-assembly | 47 | 35 |
|
|
|
| Sway bar links/Stabilizer links | Front stabilizer link assembly to Front shock absorber assembly | 74 | 55 |
|
|
|
| Control arm | Front lower suspension arm to Steering knuckle | 98 | 72 |
|
|
|
| Control arm | Front lower suspension arm to Front suspension crossmember sub-assembly | 137 | 101 |
|
|
|
| Control arm | Front lower suspension arm to Body | 160 | 118 |
|
|
|
| Ball joint | Ball joint fastener to steering knuckle. | 65 | 48 | Use a combinatio spanner #19. Use a torque wrench. |
|
|
general torque settings
Save to email ✉️| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to |
|---|
By M 93 - Own work, CC BY-SA 3.0 de
Did you find the answer to your specific question?
👍 5 👎 5
