Toyota Corolla E140 (2007-2013) Torque Spec Settings
Below you'll find the tightening torques for the Toyota Corolla E140 in both Nm and ft/lbs. The first table contains the most-used torque settings. The tables after it contain all torque spec values I could find.
Most-used torque specs for Toyota Corolla E140
Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
---|---|---|---|---|---|---|
Spark plugs | Spark plugs | 19 | 14 |
|
||
Spark plugs | Spark plugs | 20 | 15 |
|
||
Water pump | Water pump pulley bolts | 26 | 19 |
|
To make sure these are the correct tightening torque values, you can use the data below to verify this is the right model.
Are these torque settings right for you?
- Production years: 2007 - 2013
- Generation: 10
- Type of van: car
- Model variant: Base
All Torque Settings in Tables
engine torque settings
Save to email ✉️Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
---|---|---|---|---|---|---|
Oil pan | Oil pan drain plug to Oil pan subassembly | 25 | 18 |
|
||
Oil pan | Oil pan drain plug to Oil pan | 37 | 27 |
|
||
Oil pan | Drain plug to Oil pan | 49 | 36 |
|
||
Oil pan | Drain plug to Automatic transaxle oil pan subassembly | 49 | 36 |
|
||
Oil pan | Oil pan mounting bolts and nuts | 9 | 7 |
|
||
Oil filter | Oil filter to Stiffening crankcase | 18 | 13 |
|
||
Oil filter | Oil filter cap assembly to Oil filter bracket | 25 | 18 |
|
||
Oil filter | Oil filter union to Stiffening crankcase assembly | 30 | 22 |
|
||
Oil filter | Oil filter bracket to Timing chain cover | 21 | 15 |
|
||
Oil pressure switch | Oil pressure switch to Cylinder block | 15 | 11 |
|
||
Oil pressure switch | Oil pressure switch to Cylinder block | 15 | 11 |
|
||
Oil dipstick | Engine oil level dipstick guide to Cylinder block | 9 | 7 |
|
||
Oil dipstick | Oil level dipstick guide to Cylinder block | 21 | 15 |
|
||
Oil pump | Oil pump drive shaft gear nut | 30 | 22 |
|
||
Oil pump | Oil pump drive shaft gear to Oil pump | 28 | 21 |
|
||
Oil pump | Oil pump cover to Oil pump | 9 | 7 |
|
||
Oil pump | Oil pump cover to Oil pump body | 9 | 7 |
|
||
Oil pump | Oil pump relief valve plug to Oil pump | 49 | 36 |
|
||
Oil pump | Oil pump relief valve plug to Oil pump body | 49 | 36 |
|
||
Oil pump | Oil pump strainer to Oil pump | 9 | 7 |
|
||
Oil pump | Oil pump to Cylinder block | 19 | 14 |
|
||
Oil pump | Oil pump assembly to Stiffening crankcase assembly | 21 | 15 |
|
||
Oil pump | Oil pump assembly to Transaxle case | 22 | 16 |
|
||
Oil pump | Oil pump assembly to Transaxle housing | 22 | 16 |
|
||
Oil pump | Oil pump body to Stator shaft assembly | 10 | 7 |
|
||
Oil pump | Stator shaft assembly to Front oil pump body | 10 | 7 |
|
||
Piston rods | Connecting rod cap bolts | 25 | 18 |
|
||
Cylinder head | Cylinder head cover gasket and sub-assy mounting bolts (Bolt A) and nuts | 11 | 8 |
|
||
Cylinder head | Cylinder head cover gasket and sub-assy mounting bolts (Bolt B) | 14 | 10 |
|
||
Cylinder head | Cylinder head stud bolts | 5 | 4 | Bolt A and B |
|
|
Cylinder head | Cylinder head stud bolts | 10 | 7 | Bolt C and D |
|
|
Cylinder head | Straight head screw plugs | 86 | 63 |
|
||
Cylinder head | Straight head screw plugs | 44 | 32 |
|
||
Cylinder head | Cylinder head set bolts and plate washers | 70 | 52 |
|
||
Cylinder head | Cylinder head set bolts and plate washers | 49 | 36 |
|
||
Cylinder head | Ground cable to Cylinder head mounting bolts | 8 | 6 |
|
||
Spark plugs | Spark plugs | 19 | 14 |
|
||
Spark plugs | Spark plugs | 20 | 15 |
|
||
Intake manifold | Intake manifold mounting bolt and nut | 30 | 22 |
|
||
Intake manifold | Intake manifold and intake stay mounting bolt and nut | 28 | 21 |
|
||
Throttle body | Throttle body mounting bolts | 30 | 22 |
|
||
Engine block | Cylinder block drain cock plug | 13 | 10 |
|
||
Engine block | PCV valve | 19 | 14 |
|
||
Engine block | Duty vacuum switching valve | 3 | 2 |
|
||
Engine block | Cylinder block stud bolt | 22 | 16 | Bolt A |
|
|
Engine block | Cylinder block stud bolt | 5 | 4 | Bolt B and D |
|
|
Engine block | Cylinder block stud bolt | 10 | 7 | Bolt C |
|
|
Engine block | Oil nozzle sub-assembly bolts | 7 | 5 |
|
||
Engine block | No. 1 ventilation case mounting bolts and nuts | 10 | 7 |
|
||
Engine block | Crankcase stud bolt | 5 | 4 |
|
||
Engine mounts | Engine mounting insulator sub-assembly RH mounting bolt and nut | 52 | 38 | Bolt A and Nut B |
|
|
Engine mounts | Engine mounting insulator sub-assembly RH mounting bolt and nut | 95 | 70 | Bolt B and Nut A |
|
|
Engine mounts | Engine mounting bracket LH to Manual transaxle assembly | 52 | 38 |
|
||
Engine mounts | Engine mounting bracket LH to Manual transaxle | 52 | 38 |
|
||
Engine mounts | Engine mounting bracket LH to Automatic transaxle | 52 | 38 |
|
||
Engine mounts | Engine mounting bracket LH to Automatic transaxle | 52 | 38 |
|
||
Engine mounts | Front engine mounting bracket to Manual transaxle assembly | 64 | 47 |
|
||
Engine mounts | Front engine mounting bracket to Manual transaxle | 64 | 47 |
|
||
Engine mounts | Front engine mounting bracket to Automatic transaxle | 64 | 47 |
|
||
Engine mounts | Front engine mounting bracket to Automatic transaxle | 64 | 47 |
|
||
Engine mounts | Rear engine mounting bracket to Manual transaxle assembly | 45 | 33 |
|
||
Engine mounts | Rear engine mounting bracket to Manual transaxle | 45 | 33 |
|
||
Engine mounts | Rear engine mounting bracket to Automatic transaxle | 45 | 33 |
|
||
Engine mounts | Rear engine mounting bracket to Automatic transaxle | 45 | 33 | TMC made, Silver colored bolt |
|
|
Engine mounts | Rear engine mounting bracket to Automatic transaxle | 64 | 47 | TMC made, Black colored bolt |
|
|
Engine mounts | Rear engine mounting bracket to Automatic transaxle | 45 | 33 | Except TMC made |
|
|
Sensor | Air fuel ratio sensor | 44 | 32 | Without SST |
|
|
Sensor | Air fuel ratio sensor | 40 | 30 | With SST |
|
|
Sensor | Camshaft position sensor | 9 | 7 |
|
||
Sensor | Crankshaft position sensor | 10 | 7 |
|
||
Sensor | Engine Control Module (ECM) | 8 | 6 |
|
||
Sensor | Engine coolant temperature sensor | 20 | 15 |
|
||
Sensor | Heated oxygen sensor | 44 | 32 | Without SST |
|
|
Sensor | Heated oxygen sensor | 40 | 30 | With SST |
|
|
Sensor | Knock sensor | 20 | 15 |
|
||
Sensor | Front speed sensor to Knuckle | 9 | 7 |
|
||
Sensor | Front speed sensor to Body | 8 | 6 |
|
||
Sensor | Front speed sensor with brake flexible hose to Absorber | 29 | 21 |
|
||
Sensor | Speed sensor NC to Automatic transaxle | 9 | 7 |
|
||
Sensor | Speed sensor NT to Automatic transaxle | 11 | 8 |
|
||
Sensor | Speed sensor to Automatic transaxle | 5 | 4 |
|
||
Sensor | Yaw rate and acceleration sensor to Body | 20 | 15 |
|
||
Alternator | Generator coil assembly mounting bolts | 6 | 4 |
|
||
Alternator | Cord clip mounting bolts | 5 | 4 |
|
||
Alternator | Generator rear end cover nuts | 5 | 4 |
|
||
Alternator | Generator clutch pulley | 111 | 82 | Without SST |
|
|
Alternator | Generator clutch pulley | 84 | 62 | With SST |
|
|
Alternator | Generator assembly mounting bolts to cylinder block | 21 | 15 | Bolt A |
|
|
Alternator | Generator assembly mounting bolts to cylinder block | 52 | 38 | Bolt B |
|
|
Alternator | Generator wire to Terminal B nut | 10 | 7 |
|
||
Starter | Starter assembly to Transaxle housing | 37 | 27 |
|
||
Starter | Starter assembly to Transaxle housing | 37 | 27 |
|
||
Starter | Commutator end frame to Starter brush holder assembly | 2 | 1 |
|
||
Starter | Commutator end frame to Starter brush holder assembly | 2 | 1 |
|
||
Starter | Commutator end frame to Starter housing | 6 | 4 |
|
||
Starter | Commutator end frame to Starter housing | 6 | 4 |
|
||
Starter | Magnet starter switch assembly to Starter housing | 8 | 6 |
|
||
Starter | Magnet starter switch assembly to Starter housing | 8 | 6 |
|
||
Battery | Battery terminal | 5 | 4 |
|
||
Battery | Battery carrier to Frame | 13 | 10 |
|
||
Battery | Battery carrier to Body | 13 | 10 |
|
||
Battery | Battery clamp bolt | 4 | 3 |
|
||
Battery | Battery clamp to Body | 7 | 5 |
|
||
Battery | Battery clamp to Body bolt | 17 | 13 |
|
||
Battery | Battery clamp to Body nut | 4 | 3 |
|
||
Battery | Ignition coils | 9 | 7 |
|
||
Battery | Ignition coils | 10 | 7 |
|
||
Camshaft | Camshaft timing oil control valve mounting bolt | 9 | 7 |
|
||
Camshaft | Camshaft timing oil control valve mounting bolt | 10 | 7 |
|
||
Camshaft | Camshaft timing sprocket set bolt | 54 | 40 |
|
||
Camshaft | Camshaft timing exhaust gear to Camshaft | 39 | 29 | With SST |
|
|
Camshaft | Camshaft timing exhaust gear to Camshaft | 54 | 40 | Without SST |
|
|
Camshaft | Camshaft bearing cap | 30 | 22 | (No.1/No.2) |
|
|
Camshaft | Camshaft bearing cap | 9 | 7 | (No.3) |
|
|
Camshaft | Camshaft bearing cap | 16 | 12 |
|
||
Camshaft | Camshaft housing mounting bolts | 27 | 20 |
|
||
Crankshaft | Crankshaft main bearing cap | 20 | 15 | (Initial) |
|
|
Crankshaft | Crankshaft main bearing cap | 40 | 30 | (final) |
|
|
Crankshaft | Crankshaft pulley | 180 | 133 | (final) |
|
|
Crankshaft | Crankshaft pulley to Crankshaft | 190 | 140 |
|
||
Crankshaft | Balance shaft housing to Stiffening crankcase assembly | 22 | 16 | Stage 1 |
|
|
Crankshaft | Stiffening crankcase assembly to Cylinder block | 24 | 18 |
|
||
Crankshaft | Stiffening crankcase assembly to Cylinder block | 21 | 15 |
|
||
Water pump | Water inlet mounting nuts | 10 | 7 |
|
||
Water pump | Water pump and clamp bracket bolts | 9 | 7 |
|
||
Water pump | Water pump assembly to Timing chain or belt cover subassembly bolt | 26 | 19 | Bolt A |
|
|
Water pump | Water pump assembly to Timing chain or belt cover subassembly bolt | 24 | 18 | Bolt B |
|
|
Water pump | Water pump pulley bolts | 26 | 19 |
|
||
Fuel/Oil cooler | Oil cooler hose to Fan shroud | 6 | 4 |
|
||
Fuel/Oil cooler | Oil cooler hose to Fan shroud | 6 | 4 |
|
||
Fuel/Oil cooler | Oil cooler tube to Automatic transaxle | 12 | 9 |
|
||
Fuel/Oil cooler | Oil cooler tube to Transmission oil filler tube subassembly | 12 | 9 |
|
||
Fuel/Oil cooler | Oil cooler tube union to Automatic transaxle | 27 | 20 |
|
||
Fuel/Oil cooler | Inlet oil cooler elbow to Transaxle case | 27 | 20 |
|
||
Fuel/Oil cooler | Outlet oil cooler union to Transaxle case | 27 | 20 |
|
||
Coolant expansion tank | Radiator reserve tank assembly to Body | 7 | 5 |
|
||
Coolant expansion tank | Radiator reserve tank to Body | 7 | 5 |
|
||
Radiator | Radiator pipe to Battery carrier | 9 | 7 |
|
||
Radiator | Cooling fan nut | 6 | 4 |
|
||
Radiator | Fan shroud bolts | 7 | 5 |
|
||
Radiator | Upper radiator support sub-assembly mounting bolt | 6 | 4 |
|
||
Radiator | Upper radiator support mounting bolts | 19 | 14 |
|
||
Air conditioning | Air conditioning unit assembly to Body | 10 | 7 |
|
||
Air conditioning | Air conditioning unit assembly to Instrument panel reinforcement assembly | 10 | 7 |
|
||
Air conditioning | Air conditioning pressure sensor to Air conditioning tube assembly | 11 | 8 |
|
||
Air conditioning | No.1 cooler evaporator subassembly to Cooler expansion valve | 4 | 3 |
|
||
Air conditioning | Suction pipe subassembly to Air conditioning tube assembly | 10 | 7 |
|
||
Air conditioning | Compressor assembly with pulley to Engine | 25 | 18 |
|
||
Air conditioning | Compressor assembly with pulley to Engine | 25 | 18 |
|
||
Air conditioning | Compressor assembly with pulley to Engine stud bolt | 10 | 7 |
|
||
Air conditioning | Compressor assembly with pulley to Engine stud bolt | 10 | 7 |
|
||
Air conditioning | Discharge hose subassembly to Compressor assembly with pulley | 10 | 7 |
|
||
Air conditioning | Discharge hose subassembly to Compressor assembly with pulley | 10 | 7 |
|
||
Air conditioning | Suction hose subassembly to Compressor assembly with pulley | 10 | 7 |
|
||
Air conditioning | Suction hose subassembly to Compressor assembly with pulley | 10 | 7 |
|
||
Air conditioning | Discharge hose subassembly to Condenser assembly with receiver | 5 | 4 |
|
||
Air conditioning | Air conditioning tube assembly to Condenser assembly with receiver | 5 | 4 |
|
||
Air conditioning | Cap to Condenser assembly with receiver | 3 | 2 |
|
||
Belt tensioner/Timing chains | Chain tensioner plate mounting bolt | 12 | 9 |
|
||
Belt tensioner/Timing chains | Chain tensioner plate to Stiffening crankcase assembly | 10 | 7 |
|
||
Belt tensioner/Timing chains | No. 1 chain vibration damper mounting bolt | 9 | 7 |
|
||
Belt tensioner/Timing chains | No. 1 chain vibration damper mounting bolt | 21 | 15 |
|
||
Belt tensioner/Timing chains | Chain tensioner slipper mounting bolt | 19 | 14 |
|
||
Belt tensioner/Timing chains | Timing chain guide mounting bolt | 9 | 7 |
|
||
Belt tensioner/Timing chains | Chain tensioner mounting nut | 9 | 7 |
|
||
Belt tensioner/Timing chains | V-ribbed belt tensioner bolt and nut | 60 | 44 |
|
||
Valve cover | Valve body to Automatic transaxle | 11 | 8 |
|
||
Valve cover | Oil strainer to Valve body | 11 | 8 |
|
||
Fuel system | Charcoal canister assembly bolt | 19 | 14 |
|
||
Fuel system | Fuel delivery pipe sub-assembly mounting bolt | 20 | 15 |
|
||
Fuel system | Fuel delivery pipe subassembly to Cylinder head subassembly | 21 | 15 |
|
||
Fuel system | Fuel pressure pulsation damper mounting bolt | 9 | 7 |
|
||
Fuel system | Fuel tank band to Body | 39 | 29 |
|
||
Fuel system | Fuel tank band to Body | 39 | 29 |
|
||
Fuel system | No.1 fuel tank protector subassembly to Fuel tank | 6 | 4 |
|
||
Fuel system | No.1 fuel tank protector to Fuel tank band | 6 | 4 |
|
||
Fuel system | No.1 fuel tank protector to Body | 6 | 4 |
|
||
Fuel system | No.1 fuel tank protector to Body | 6 | 4 |
|
drivetrain torque settings
Save to email ✉️Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
---|---|---|---|---|---|---|
Differential | Front differential ring gear to Front differential case | 77 | 57 |
|
||
Differential | Front differential ring gear to Front differential case | 106 | 78 |
|
||
Differential | Front differential case to Front differential ring gear | 95 | 70 |
|
||
Differential | Differential case to Front differential ring gear | 88 | 65 |
|
||
Differential | Differential gear lube apply tube and No.1 transaxle apply tube clamp to Transaxle housing | 10 | 7 |
|
||
Wheel hub assembly | Front drive shaft assembly to Front axle hub nut | 216 | 159 |
|
||
Wheel hub assembly | Rear axle beam assembly to Rear axle hub and bearing assembly | 100 | 74 |
|
||
Clutch assembly | Clutch release cylinder assembly to Transaxle bolts | 12 | 9 | Bolts A, B |
|
|
Clutch assembly | Clutch release cylinder assembly to Transaxle bolt | 8 | 6 | Bolt C |
|
|
Clutch assembly | Release cylinder bleeder plug to Clutch release cylinder | 8 | 6 |
|
||
Clutch assembly | Clutch master cylinder push rod clevis lock nut | 12 | 9 |
|
||
Clutch assembly | Clutch line to Clutch release cylinder | 14 | 10 |
|
||
Clutch assembly | Clutch line to Clutch release cylinder | 15 | 11 | For use without union nut wrench |
|
|
Clutch assembly | Clutch line to Clutch master cylinder | 14 | 10 |
|
||
Clutch assembly | Clutch line to Clutch master cylinder | 15 | 11 | For use without union nut wrench |
|
|
Clutch assembly | Clutch line clamp to Clutch release cylinder | 12 | 9 |
|
||
Clutch assembly | Clutch line bracket to Manual transaxle | 8 | 6 |
|
||
Clutch assembly | Clutch tube bracket to Manual transaxle | 12 | 9 |
|
||
Clutch assembly | Clutch tube bracket to Manual transaxle case | 8 | 6 |
|
||
Clutch assembly | Clutch accumulator bracket to Clutch accumulator | 12 | 9 |
|
||
Clutch assembly | Clutch accumulator bracket to Starter assembly | 37 | 27 |
|
||
Clutch assembly | Clutch accumulator assembly to Release cylinder assembly | 12 | 9 |
|
||
Clutch assembly | Clutch accumulator assembly to Clutch line | 14 | 10 |
|
||
Clutch assembly | Clutch accumulator assembly to Clutch line | 15 | 11 | For use without union nut wrench |
|
|
Flywheel/Flex plate | Drive plate and ring gear subassembly to Crankshaft | 98 | 72 |
|
||
Flywheel/Flex plate | Drive plate and ring gear to Crankshaft | 88 | 65 |
|
||
Flywheel/Flex plate | Flywheel subassembly to Crankshaft | 130 | 96 |
|
||
Flywheel/Flex plate | Flywheel subassembly to Crankshaft | 49 | 36 | Stage 1 |
|
|
Flywheel/Flex plate | Clutch cover assembly to Flywheel subassembly | 19 | 14 |
|
||
Transmission fluid pan | Filler plug to Manual transmission case | 39 | 29 |
|
||
Transmission fluid pan | Filler plug to Transmission case | 49 | 36 |
|
||
Transmission fluid pan | Drain plug to Manual transmission case | 39 | 29 |
|
||
Transmission fluid pan | Drain plug to Transmission case | 49 | 36 |
|
||
Transmission fluid pan | Transmission oil filler tube subassembly to Automatic transaxle | 6 | 4 |
|
||
Transmission fluid pan | Transmission oil filler tube subassembly to Automatic transaxle | 6 | 4 |
|
||
Transmission fluid pan | Oil pan to Automatic transaxle | 11 | 8 |
|
||
Transmission fluid pan | Automatic transaxle oil pan subassembly to Automatic transaxle case | 8 | 6 |
|
||
Transmission fluid pan | Transmission oil baffle to Manual transmission case | 17 | 13 |
|
||
Transmission mount/case | Manual transaxle assembly to Engine | 33 | 24 |
|
||
Transmission mount/case | Manual transaxle to Engine | 44 | 32 |
|
||
Transmission mount/case | Transaxle housing to Engine bolt | 64 | 47 | Bolt A |
|
|
Transmission mount/case | Transaxle housing to Engine bolts | 46 | 34 | Bolts B and C |
|
|
Transmission mount/case | Transaxle housing to Engine bolt | 44 | 32 | Bolt D |
|
|
Transmission mount/case | Transaxle housing to Transaxle case bolts | 29 | 21 | Bolts A and B |
|
|
Transmission mount/case | Transaxle housing to Transaxle case bolt | 22 | 16 | Bolt C |
|
|
Transmission mount/case | Transaxle housing to Transaxle case bolt | 10 | 7 | Bolt D |
|
|
Transmission mount/case | Transaxle housing to Transaxle case bolt | 33 | 24 | Bolt E |
|
|
Transmission mount/case | Transaxle housing to Transaxle case bolt | 25 | 18 | Bolt F |
|
|
Transmission mount/case | Transaxle housing to Transaxle case bolt | 29 | 21 | Bolt A |
|
|
Transmission mount/case | Transaxle housing to Transaxle case bolt | 22 | 16 | Bolt B |
|
|
Transmission mount/case | Transmission valve body assembly to Automatic transaxle | 11 | 8 |
|
||
Transmission mount/case | Transmission case to Transaxle case | 29 | 21 |
|
||
Transmission mount/case | Transmission case to Manual transaxle case | 29 | 21 |
|
||
Transmission mount/case | Transmission case cover to Transmission case | 21 | 15 |
|
||
Transmission mount/case | Upper transaxle case cover to Automatic transaxle | 12 | 9 |
|
||
Transmission mount/case | No.1 transaxle case plug to Automatic transaxle | 7 | 5 |
|
||
Transmission mount/case | No.1 transaxle case plug to Transaxle rear cover | 7 | 5 |
|
||
Transmission mount/case | No.1 transaxle case plug to Transaxle case | 7 | 5 |
|
||
Transmission mount/case | Transaxle rear cover to Transaxle case bolt | 19 | 14 | Bolt A |
|
|
Transmission mount/case | Transaxle rear cover to Transaxle case bolt | 25 | 18 | Other bolt |
|
|
Transmission mount/case | Rear transaxle cover assembly to Transaxle case | 25 | 18 |
|
||
Transmission mount/case | Rear transaxle cover plug to Rear transaxle cover | 7 | 5 |
|
||
Transmission mount/case | Manual detent spring to Transaxle case bolt | 20 | 15 | Bolt A |
|
|
Transmission mount/case | Manual detent spring to Transaxle case bolt | 12 | 9 | Bolt B |
|
|
Transmission mount/case | Manual detent spring subassembly to Transmission valve body assembly | 11 | 8 |
|
||
Torque converter | Drive plate and ring gear to Torque converter | 28 | 21 |
|
||
Torque converter | Torque converter clutch to Drive plate | 41 | 30 |
|
||
Torque converter | Torque converter set bolt to Drive plate | 28 | 21 |
|
||
Transfer | Transmission control cable assembly to Control shaft lever | 12 | 9 |
|
||
Transfer | Control shaft lever to Control shaft | 13 | 10 |
|
||
Transfer | Shift lever assembly to Body | 12 | 9 |
|
||
Transfer | Shift lever assembly to Body | 12 | 9 |
|
||
Transfer | Shift lever assembly to Body | 12 | 9 |
|
||
Transfer | Shift lever assembly to Body | 12 | 9 |
|
||
Transfer | Shift control cable to Control shaft lever | 12 | 9 |
|
||
Transfer | Reverse shift arm bracket to Transaxle case | 17 | 13 |
|
||
Transfer | Reverse shift arm bracket to Manual transaxle case | 17 | 13 |
|
||
Transfer | Reverse idler gear shaft bolt to Transmission case | 29 | 21 |
|
||
Transfer | Reverse idler gear shaft bolt to Transmission case | 30 | 22 |
|
||
Transfer | Park/Neutral position switch bolt | 5 | 4 |
|
||
Transfer | Park/Neutral position switch nut | 7 | 5 |
|
||
Transfer | Park/Neutral position switch assembly to Automatic transaxle | 5 | 4 |
|
||
Transfer | Lock plate to Park/Neutral position switch assembly | 7 | 5 |
|
||
Transfer | Pawl shaft clamp to Transaxle case | 10 | 7 |
|
||
Transfer | Parking lock pawl bracket to Transaxle case | 20 | 15 |
|
||
Transfer | Parking lock pawl bracket to Transaxle case | 20 | 15 |
|
||
Drive/Axle shaft | Front drive shaft assembly RH to Bearing bracket | 32 | 24 |
|
||
Drive/Axle shaft | Drive shaft bearing bracket to Cylinder block | 64 | 47 |
|
steering torque settings
Save to email ✉️Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
---|---|---|---|---|---|---|
Tie rod end | Tie rod end subassembly lock nuts | 74 | 55 |
|
||
Tie rod end | Tie rod end subassembly to Steering knuckle | 49 | 36 |
|
||
Steering knuckle | Front flexible hose to Steering knuckle | 29 | 21 |
|
||
Steering rack | Steering link assembly set bolts | 58 | 43 |
|
||
Steering column | No.2 steering intermediate shaft assembly to Steering column assembly | 35 | 26 |
|
||
Steering column | Steering post assembly set bolt | 25 | 18 |
|
||
Steering column | Steering post assembly set nuts | 25 | 18 |
|
||
Steering shaft | No.2 steering intermediate shaft assembly to Steering intermediate shaft assembly | 35 | 26 |
|
||
Steering shaft | Steering intermediate shaft to Steering link assembly | 35 | 26 |
|
||
Steering wheel | Steering wheel set nut | 50 | 37 |
|
||
Steering wheel | Steering pad to Steering wheel assembly | 9 | 7 |
|
||
Power steering pump | Power steering ECU assembly set bolt | 8 | 6 |
|
||
Power steering pump | Power steering ECU assembly set nuts | 8 | 6 |
|
exhaust torque settings
Save to email ✉️Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
---|---|---|---|---|---|---|
Exhaust manifold | Exhaust manifold to Cylinder head | 21 | 15 |
|
||
Exhaust manifold | Front exhaust pipe assembly to Exhaust manifold converter subassembly | 43 | 32 |
|
||
Exhaust manifold | Front exhaust pipe assembly to Exhaust manifold | 43 | 32 |
|
||
Exhaust manifold | Front exhaust pipe assembly to Center exhaust pipe assembly | 43 | 32 |
|
||
Exhaust manifold | Center exhaust pipe assembly to Tail exhaust pipe assembly | 43 | 32 |
|
||
Exhaust manifold | Front exhaust pipe assembly to Tail exhaust pipe assembly | 43 | 32 |
|
||
Exhaust manifold | Exhaust manifold converter subassembly to Cylinder head subassembly | 37 | 27 |
|
||
Exhaust manifold | Exhaust manifold heat insulator mounting bolts | 12 | 9 |
|
||
Exhaust manifold | Manifold stay to Exhaust manifold converter subassembly | 44 | 32 |
|
||
Exhaust manifold | Exhaust manifold stay to Exhaust manifold | 43 | 32 |
|
||
Exhaust manifold | Manifold stay to Cylinder block | 44 | 32 |
|
||
Exhaust manifold | Exhaust manifold stay to Cylinder block | 43 | 32 |
|
brakes torque settings
Save to email ✉️Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
---|---|---|---|---|---|---|
Disc brake | Steering knuckle to Front disc brake caliper assembly | 107 | 79 |
|
||
Disc brake | Rear disc brake dust cover subassembly to Rear disc brake caliper assembly | 63 | 46 |
|
||
Disc brake | Steering knuckle to Front disc brake dust cover | 8 | 6 |
|
||
Disc brake | Front disc brake cylinder assembly to Front disc brake cylinder mounting | 34 | 25 |
|
||
Disc brake | Rear disc brake cylinder assembly to Rear disc brake cylinder mounting | 35 | 26 | For Disc type |
|
|
Disc brake | Rear disc brake cylinder mounting to Backing plate | 63 | 46 | For Disc type |
|
|
Disc brake | Rear wheel brake cylinder assembly to Backing plate | 10 | 7 | For Drum type |
|
|
Disc brake | Front disc brake bleeder plug | 8 | 6 |
|
||
Disc brake | Rear disc brake bleeder plug | 10 | 7 | For Disc type |
|
|
Disc brake | Rear drum brake bleeder plug | 9 | 7 | For Drum type |
|
|
Disc brake | Brake actuator to Brake actuator bracket | 5 | 4 |
|
||
Disc brake | Brake actuator bracket to Body | 19 | 14 |
|
||
Brake line | Front flexible hose to Front disc brake cylinder assembly | 29 | 21 |
|
||
Brake line | Rear brake flexible hose to Rear disc brake cylinder assembly | 29 | 21 | For Disc type |
|
|
Brake line | Front flexible hose to Absorber bracket | 29 | 21 |
|
||
Brake line | Rear flexible hose to Rear axle beam | 29 | 21 | For Disc type |
|
|
Brake line | Rear wheel brake cylinder assembly to Brake line | 14 | 10 | For Drum type |
|
|
Brake line | Rear wheel brake cylinder assembly to Brake line | 15 | 11 | For Drum type, For use without a union nut wrench |
|
|
Brake line | Brake line to Front flexible hose | 14 | 10 |
|
||
Brake line | Brake line to Front flexible hose | 15 | 11 | For use without a union nut wrench |
|
|
Brake line | Rear flexible hose to Brake line | 14 | 10 | For Disc type |
|
|
Brake line | Rear flexible hose to Brake line | 15 | 11 | For Disc type, For use without a union nut wrench |
|
|
Brake line | Rear flexible hose to Brake line | 14 | 10 | For Drum type |
|
|
Brake line | Rear flexible hose to Brake line | 15 | 11 | For Drum type, For use without a union nut wrench |
|
|
Brake line | Brake actuator to Brake line | 14 | 10 | Without VSC |
|
|
Brake line | Brake actuator to Brake line | 15 | 11 | Without VSC, For use without union nut wrench |
|
|
Brake line | Brake actuator to Brake line | 14 | 10 | With VSC, Flare nut 10mm |
|
|
Brake line | Brake actuator to Brake line | 15 | 11 | With VSC, Flare nut 10mm, For use without union nut wrench |
|
|
Brake line | Brake actuator to Brake line | 18 | 13 | With VSC, Flare nut 12mm |
|
|
Brake line | Brake actuator to Brake line | 20 | 15 | With VSC, Flare nut 12mm, For use without union nut wrench |
|
|
Brake booster | Brake pedal support to Brake booster assembly | 13 | 10 |
|
||
Brake pedal | Brake pedal support to Instrument panel reinforcement | 24 | 18 |
|
||
Brake pedal | Brake pedal subassembly to Brake pedal support | 37 | 27 |
|
||
Brake pedal | Accelerator pedal bolts | 6 | 4 |
|
||
Brake pedal | Clutch master cylinder to Clutch pedal support | 13 | 10 |
|
||
Brake pedal | Clutch pedal support to Body | 24 | 18 |
|
||
Brake pedal | Clutch pedal stopper bolt to Lock nut | 25 | 18 |
|
||
Brake pedal | Clutch pedal subassembly to Clutch pedal support | 37 | 27 |
|
||
Brake pedal | Clutch pedal switch assembly to Clutch pedal support | 16 | 12 |
|
||
Brake pedal | Clutch switch assembly to Clutch pedal support | 16 | 12 |
|
||
Master cylinder | Brake master cylinder subassembly to Brake booster assembly | 13 | 10 |
|
||
Master cylinder | Brake master cylinder push rod clevis lock nut | 26 | 19 |
|
||
Parking brake | Parking brake cable to Body | 5 | 4 |
|
||
Parking brake | Parking brake cable assembly to Body | 5 | 4 |
|
||
Parking brake | Parking brake lever assembly set bolts | 15 | 11 |
|
||
Parking brake | Parking brake switch assembly set screw | 1 | 1 |
|
||
Parking brake | No.1 parking brake cable assembly lock nut | 6 | 4 |
|
||
Parking brake | No.3 parking brake cable assembly set bolts | 6 | 4 | For rear disc brake |
|
|
Parking brake | No.3 parking brake cable assembly set bolts | 6 | 4 | For rear drum brake |
|
|
Parking brake | No.3 parking brake cable assembly to Backing plate | 8 | 6 | For rear drum brake |
|
suspension torque settings
Save to email ✉️Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
---|---|---|---|---|---|---|
Wheels | Front wheel set nuts | 103 | 76 |
|
||
Wheels | Rear wheel set nuts | 103 | 76 |
|
||
Struts | Tower bar bracket subassembly LH to Suspension tower damper assembly | 52 | 38 |
|
||
Struts | Tower bar bracket subassembly LH to Body | 50 | 37 |
|
||
Shock absorbers/shocks | Front shock absorber with coil spring to Body | 39 | 29 | TMC made |
|
|
Shock absorbers/shocks | Front shock absorber with coil spring to Body | 50 | 37 | Except TMC made |
|
|
Shock absorbers/shocks | Rear shock absorber with coil spring to Body | 80 | 59 |
|
||
Shock absorbers/shocks | Front shock absorber with coil spring to Steering knuckle | 240 | 177 |
|
||
Shock absorbers/shocks | Front shock absorber nut to Piston rod | 47 | 35 |
|
||
Shock absorbers/shocks | Rear support to Rear shock absorber nut to Piston rod | 39 | 29 |
|
||
Shock absorbers/shocks | Rear shock absorber with coil spring to Rear axle beam | 80 | 59 |
|
||
Shock absorbers/shocks | Front flexible hose to Front shock absorber | 29 | 21 |
|
||
Stabilizer bar | No.1 front stabilizer bracket to Front suspension member | 19 | 14 | TMC made |
|
|
Stabilizer bar | No.1 front stabilizer bracket to Front suspension member | 24 | 18 | Except TMC made |
|
|
Stabilizer bar | Front stabilizer link to Front stabilizer bar | 74 | 55 |
|
||
Stabilizer bar | Rear axle beam to Rear stabilizer bar | 250 | 184 |
|
||
Sway bar links/Stabilizer links | Front shock absorber with coil spring to Front stabilizer link | 74 | 55 |
|
||
Control arm | Front lower suspension arm to Front suspension crossmember | 137 | 101 | Bolt type 1 |
|
|
Control arm | Front lower suspension arm to Front suspension crossmember | 145 | 107 | Bolt type 2 |
|
|
Ball joint | Front lower ball joint to Steering knuckle | 123 | 91 | 2AZ-FE Engine Code |
|
|
Ball joint | Front lower ball joint to Steering knuckle | 103 | 76 | 2ZR-FE Engine Code |
|
general torque settings
Save to email ✉️Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to |
---|
Did you find the answer to your specific question?
👍 3 👎 2