Toyota Corolla E120 (2002-2008) Torque Spec Settings
Below you'll find the tightening torques for the Toyota Corolla E120 in both Nm and ft/lbs. The first table contains the most-used torque settings. The tables after it contain all torque spec values I could find.
Most-used torque specs for Toyota Corolla E120
Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
---|---|---|---|---|---|---|
Intake manifold | Intake manifold | 19 | 14 |
|
To make sure these are the correct tightening torque values, you can use the data below to verify this is the right model.
Are these torque settings right for you?
- Production years: 2002 - 2008
- Generation: 9
- Type of van: car
- Model variant: Base
- Also known as:
All Torque Settings in Tables
engine torque settings
Save to email ✉️Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
---|---|---|---|---|---|---|
Oil pan | Oil pan drain plug to Oil pan No.2 | 38 | 28 |
|
||
Oil pan | Oil pan to Oil pan cover | 6 | 4 |
|
||
Oil pressure switch | Oil pressure switch to Cylinder block assembly | 15 | 11 |
|
||
Oil pump | Timing chain cover No.2 to Oil pump assembly | 6 | 4 |
|
||
Oil pump | Fan belt adjusting bar to Oil pump assembly | 11 | 8 |
|
||
Oil pump | Oil pump assembly to Cylinder block assembly bolt | 11 | 8 | Bolt A |
|
|
Oil pump | Oil pump assembly to Cylinder block assembly bolt | 24 | 18 | Bolt B |
|
|
Oil pump | Oil pump assembly to Cylinder block assembly bolt | 11 | 8 | Bolt C |
|
|
Oil pump | Oil pump assembly to Cylinder block assembly bolt | 24 | 18 | Bolt D |
|
|
Oil pump | Oil pump assembly to Cylinder block assembly nut | 24 | 18 |
|
||
Oil pump | Oil pickup tube | 11 | 8 |
|
||
Vacuum pump | Vacuum pump to Engine | 21 | 15 |
|
||
Vacuum pump | Vacuum pump to Cam position sensor | 9 | 7 |
|
||
Piston rods | Connecting rod bolts | 20 | 15 |
|
||
Cylinder head | Cylinder head bolts | 34 | 25 |
|
||
Cylinder head | Cylinder head bolts | 49 | 36 |
|
||
Cylinder head | Cylinder head assembly to EGR pipe connector | 20 | 15 |
|
||
Cylinder head | Cylinder head assembly to Intake air connector | 20 | 15 |
|
||
Cylinder head | Cylinder head assembly to Engine hanger | 40 | 30 |
|
||
Cylinder head | Cylinder head cover subassembly to Cylinder head assembly | 13 | 10 |
|
||
Cylinder head | Cylinder head cover subassembly to Vacuum reservoir tube | 11 | 8 |
|
||
Spark plugs | Spark plug | 18 | 13 |
|
||
Glow plugs | Glow plug assembly to Cylinder head subassembly | 13 | 10 |
|
||
Glow control unit | Glow plug connector to Glow plug assembly | 2 | 1 |
|
||
Glow control unit | Glow terminal to Glow plug connector | 4 | 3 |
|
||
Intake manifold | Intake manifold | 19 | 14 |
|
||
Intake manifold | Intake air connector bracket to Intake air connector | 20 | 15 |
|
||
Intake manifold | Intake air connector bracket to Cylinder head subassembly | 20 | 15 |
|
||
Throttle body | Throttle body to Intake air connector | 20 | 15 |
|
||
Throttle body | Throttle body assembly to Oil level gage guide | 11 | 8 |
|
||
Engine block | Cylinder block side cover to Cylinder block assembly | 7 | 5 |
|
||
Engine block | Water inlet to Cylinder block assembly | 9 | 7 |
|
||
Engine mounts | Engine mounting bracket to Cylinder block assembly | 55 | 41 |
|
||
Engine mounts | Engine mounting bracket FR to Transaxle | 64 | 47 |
|
||
Engine mounts | Engine mounting bracket FR to Transaxle | 64 | 47 |
|
||
Engine mounts | Engine mounting bracket RR to Transaxle | 64 | 47 |
|
||
Engine mounts | Engine mounting bracket RR to Transaxle | 64 | 47 |
|
||
Engine mounts | Engine mounting bracket LH to Transaxle | 52 | 38 |
|
||
Engine mounts | Engine mounting bracket LH to Transaxle | 52 | 38 |
|
||
Sensor | Engine coolant temperature sensor to Cylinder head subassembly | 20 | 15 |
|
||
Sensor | Camshaft position sensor to Vacuum pump assembly | 8 | 6 |
|
||
Sensor | Crankshaft position sensor to Cylinder block subassembly | 8 | 6 |
|
||
Sensor | Oil pan assembly to Engine oil level sensor | 7 | 5 |
|
||
Sensor | Speed sensor to Steering knuckle | 8 | 6 |
|
||
Alternator | Generator assembly to Cylinder block subassembly | 32 | 24 |
|
||
Alternator | Generator assembly to Fan belt adjusting bar | 19 | 14 |
|
||
Alternator | Generator wire to Generator assembly | 10 | 7 |
|
||
Alternator | Alternator | 24 | 18 |
|
||
Starter | Starter assembly to Front transaxle case | 37 | 27 |
|
||
Starter | Starter wire to Starter assembly | 6 | 4 |
|
||
Battery | Batter carrier to Body | 13 | 10 |
|
||
Battery | Batter carrier to Body | 13 | 10 |
|
||
Battery | Batter clamp subassembly to Body bolt | 5 | 4 |
|
||
Battery | Batter clamp subassembly to Body bolt | 5 | 4 |
|
||
Battery | Batter clamp subassembly to Body nut | 4 | 3 |
|
||
Battery | Batter clamp subassembly to Body nut | 4 | 3 |
|
||
Battery | Negative battery terminal to Battery | 5 | 4 |
|
||
Battery | Battery negative terminal to Battery negative cable | 5 | 4 |
|
||
Battery | Ignition coil | 7 | 5 |
|
||
Camshaft | Camshaft timing sprocket to Camshaft | 20 | 15 |
|
||
Camshaft | Camshaft bearing cap to Cylinder head assembly | 19 | 14 |
|
||
Crankshaft | Crankshaft damper subassembly to Crankshaft | 180 | 133 |
|
||
Crankshaft | Engine block main bearing caps | 14 | 10 | Stage 1 |
|
|
Crankshaft | Engine block main bearing caps | 43 | 32 | Stage 2 |
|
|
Crankshaft | Main cap side bolts | 19 | 14 |
|
||
Crankshaft | Crankshaft pulley | 138 | 102 |
|
||
Common rail | Common rail assembly to Cylinder head subassembly | 26 | 19 |
|
||
Common rail | Fuel inlet pipe subassembly to Common rail assembly | 23 | 17 | With SST |
|
|
Common rail | Fuel inlet pipe subassembly to Common rail assembly | 25 | 18 | Without SST |
|
|
Common rail | Injection pipe subassembly No.1 - No.4 to Common rail assembly | 23 | 17 | With SST |
|
|
Common rail | Injection pipe subassembly No.1 - No.4 to Common rail assembly | 25 | 18 | Without SST |
|
|
Common rail | Fuel rail bolts | 11 | 8 |
|
||
Water pump | Water pump assembly to Cylinder block assembly | 11 | 8 |
|
||
Water pump | Water pump pulley to Water pump assembly | 15 | 11 |
|
||
Fuel/Oil cooler | Oil cooler assembly to Oil pan | 66 | 49 |
|
||
Intercooler | Intercooler assembly to Body | 7 | 5 |
|
||
Intercooler | Intercooler cooling air duct subassembly to Intercooler assembly | 5 | 4 |
|
||
Intercooler | Intercooler air hose to Turbocharger subassembly | 6 | 4 |
|
||
Intercooler | Intercooler air hose to Air tube No.1 | 6 | 4 |
|
||
Radiator | Fan shroud assembly to Radiator assembly | 8 | 6 |
|
||
Radiator | Radiator upper support to Body | 19 | 14 |
|
||
Radiator | Relay block to Radiator upper support | 5 | 4 |
|
||
Air conditioning | A/C compressor | 24 | 18 |
|
||
Air conditioning | Magnet clutch hub to Cooler compressor assembly | 13 | 10 |
|
||
Air conditioning | Compressor and magnetic clutch to Engine | 29 | 21 |
|
||
Air conditioning | Cooler refrigerant discharge hose No.1 to Compressor and magnetic clutch | 10 | 7 |
|
||
Air conditioning | Cooler refrigerant suction hose No.1 to Compressor and magnetic clutch | 10 | 7 |
|
||
Belt tensioner/Timing chains | Belt tensioner | 69 | 51 |
|
||
Belt tensioner/Timing chains | Timing guides | 19 | 14 |
|
||
Belt tensioner/Timing chains | Timing tensioner | 11 | 8 |
|
||
Belt tensioner/Timing chains | Timing chain cover | 14 | 10 |
|
||
Valve cover | Valve cover | 12 | 9 |
|
||
PCM | ECM to Blower assembly | 3 | 2 |
|
||
PCM | ECM bracket No.1 to ECM | 3 | 2 |
|
||
PCM | ECM bracket No.2 to ECM | 3 | 2 |
|
||
PCM | ECM bracket No.3 to ECM | 3 | 2 |
|
||
Fuel system | Injection pipe subassembly No.1 - No.4 to Injector assembly | 23 | 17 | With SST |
|
|
Fuel system | Injection pipe subassembly No.1 - No.4 to Injector assembly | 25 | 18 | Without SST |
|
|
Fuel system | Injection pipe clamp No.1 to Injection pipe subassembly | 9 | 7 |
|
||
Fuel system | Injection pipe clamp No.2 to Injection pipe subassembly | 9 | 7 |
|
||
Fuel system | Supply pump assembly to Cylinder head subassembly | 20 | 15 |
|
||
Fuel system | Fuel inlet pipe subassembly to Supply pump assembly | 23 | 17 | With SST |
|
|
Fuel system | Fuel inlet pipe subassembly to Supply pump assembly | 25 | 18 | Without SST |
|
|
Fuel system | Fuel filter assembly to Fuel filter support | 18 | 13 |
|
||
Fuel system | Fuel filter assembly set bolt | 18 | 13 |
|
||
Fuel system | Fuel tank band No.1 to Body | 40 | 30 |
|
||
Fuel system | Fuel tank band No.1 to Body | 39 | 29 |
|
||
Fuel system | Fuel tank band No.1 to Body | 39 | 29 |
|
||
Fuel system | Fuel tank protector No.1 to Body | 5 | 4 |
|
||
Fuel system | Fuel tank filler pipe lower subassembly to Fuel tank assembly | 4 | 3 |
|
||
Fuel system | Fuel tank vent tube set plate to Fuel tank assembly | 6 | 4 |
|
||
Fuel system | Fuel heater assembly set bolt | 18 | 13 |
|
drivetrain torque settings
Save to email ✉️Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
---|---|---|---|---|---|---|
Wheel hub assembly | Front wheel axle nut | 216 | 159 |
|
||
Wheel hub assembly | Rear wheel hub bolts | 102 | 75 |
|
||
Clutch assembly | Clutch actuator bracket No.1 to Transaxle | 20 | 15 |
|
||
Clutch assembly | Clutch pedal subassembly to Clutch pedal support | 37 | 27 |
|
||
Clutch assembly | Clutch pedal support to Body | 19 | 14 |
|
||
Clutch assembly | Clutch pedal support to Stopper bolt | 25 | 18 |
|
||
Clutch assembly | Clutch pedal support to Clutch start switch assembly | 16 | 12 |
|
||
Clutch assembly | Clutch master cylinder push rod clevis lock nut | 12 | 9 |
|
||
Clutch assembly | Clutch master cylinder to Flexible hose tube | 15 | 11 |
|
||
Clutch assembly | Clutch master cylinder to Body | 12 | 9 |
|
||
Clutch assembly | Clutch release cylinder bleeder plug | 8 | 6 |
|
||
Clutch assembly | Clutch release cylinder to Transaxle housing | 12 | 9 |
|
||
Clutch assembly | Clutch release cylinder to Flexible hose tube | 15 | 11 |
|
||
Clutch assembly | Clutch line clamp to Clutch release cylinder | 12 | 9 |
|
||
Clutch assembly | Clutch actuator assembly set bolt | 17 | 13 |
|
||
Clutch assembly | Clutch accumulator assembly to Flexible hose tube | 15 | 11 |
|
||
Clutch assembly | Clutch cover assembly to Flywheel subassembly | 19 | 14 |
|
||
Flywheel/Flex plate | Flywheel subassembly to Crankshaft | 49 | 36 | Stage 1 |
|
|
Flywheel/Flex plate | Flywheel to Converter | 41 | 30 |
|
||
Transmission fluid pan | Filler and drain plugs | 39 | 29 |
|
||
Transmission fluid pan | Filler and drain plugs | 39 | 29 |
|
||
Transmission fluid pan | Transmission drain plug | 20 | 15 |
|
||
Transmission fluid pan | Transmission pan | 8 | 6 |
|
||
Transmission mount/case | Transaxle assembly to Engine | 33 | 24 |
|
||
Transmission mount/case | Transaxle assembly to Engine | 33 | 24 |
|
||
Transmission mount/case | Transmission case protector to Transaxle | 8 | 6 |
|
||
Transmission mount/case | Park/Neutral position switch to Transmission case | 29 | 21 |
|
||
Transmission mount/case | Transmission control ECU set bolt | 5 | 4 |
|
||
Transmission mount/case | Bell housing bolts | 72 | 53 |
|
||
Torque converter | Torque converter drain | 20 | 15 |
|
||
Transfer | Floor shift transmission control cable assembly to Body | 5 | 4 |
|
||
Transfer | Floor shift shift lever assembly to Body | 12 | 9 |
|
||
Transfer | Floor shift shift lever assembly to Body | 12 | 9 |
|
||
Drive/Axle shaft | Front drive shaft bearing case set bolt | 64 | 47 |
|
steering torque settings
Save to email ✉️Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
---|---|---|---|---|---|---|
Tie rod end | Outer tie rod | 49 | 36 |
|
||
Tie rod end | Inner tie rod | 88 | 65 |
|
||
Steering knuckle | Steering knuckle to Suspension lower arm | 89 | 66 |
|
||
Power steering | Power steering to Engine | 37 | 27 |
|
exhaust torque settings
Save to email ✉️Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
---|---|---|---|---|---|---|
Exhaust manifold | Exhaust manifold to Cylinder head assembly | 43 | 32 |
|
||
Exhaust manifold | Exhaust manifold to Heat insulator | 6 | 4 |
|
||
Exhaust manifold | Exhaust manifold to Manifold stay | 37 | 27 |
|
||
Exhaust manifold | Manifold support bracket to Exhaust manifold converter subassembly | 37 | 27 |
|
||
Exhaust manifold | Manifold support bracket to Cylinder block subassembly | 37 | 27 |
|
||
Exhaust manifold | Front exhaust pipe assembly to Exhaust manifold | 43 | 32 |
|
||
Exhaust manifold | Front exhaust pipe assembly to Exhaust tail pipe assembly | 43 | 32 |
|
||
Exhaust manifold | Front exhaust pipe assembly to Exhaust manifold converter subassembly | 43 | 32 |
|
||
Exhaust manifold | Exhaust pipe to Heater assembly (with cold area) | 8 | 6 |
|
||
Exhaust manifold | Exhaust pipe to Body (with cold area) | 8 | 6 |
|
||
Turbo | Turbocharger subassembly to Exhaust manifold | 53 | 39 |
|
||
Turbo | Turbo oil inlet pipe to Turbocharger subassembly | 24 | 18 |
|
||
Turbo | Turbo oil inlet pipe to Cylinder block subassembly | 24 | 18 |
|
||
Turbo | Turbo oil outlet pipe to Turbocharger subassembly | 11 | 8 |
|
||
Turbo | Turbo oil outlet pipe to Cylinder block subassembly | 14 | 10 |
|
||
Turbo | Exhaust manifold converter subassembly to Turbocharger subassembly | 26 | 19 |
|
||
Turbo | Turbo pressure sensor to Turbo pressure sensor bracket | 5 | 4 |
|
||
Turbo | Turbo pressure sensor to Fan shroud subassembly | 5 | 4 |
|
||
EGR | EGR valve assembly to Intake air connector | 20 | 15 |
|
||
EGR | EGR cooler assembly to EGR connector | 20 | 15 |
|
||
EGR | EGR cooler assembly to EGR valve assembly | 11 | 8 |
|
||
EGR | EGR cooler assembly to Cylinder head subassembly | 11 | 8 |
|
||
EGR | EGR pipe | 19 | 14 |
|
brakes torque settings
Save to email ✉️Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
---|---|---|---|---|---|---|
Disc brake | Front caliper | 34 | 25 |
|
||
Disc brake | Rear brake caliper | 34 | 25 |
|
||
Disc brake | Front caliper bracket | 107 | 79 |
|
||
Disc brake | Front caliper banjo bolt | 30 | 22 |
|
||
Disc brake | Rear caliper banjo bolt | 30 | 22 |
|
||
Brake line | Brake line union nut | 15 | 11 | Nut 10mm |
|
|
Brake line | Brake line union nut | 29 | 21 | Nut 14mm |
|
|
Brake booster | Brake booster to Body | 13 | 10 |
|
||
Brake booster | Brake booster clevis lock nut | 19 | 14 |
|
||
Brake pedal | Accelerator pedal assembly to Body | 5 | 4 |
|
||
Master cylinder | Brake master cylinder to Reservoir | 8 | 6 |
|
||
Master cylinder | Brake master cylinder to Brake booster | 25 | 18 |
|
||
Parking brake | Parking brake cable assembly No.2 to Body | 5 | 4 |
|
||
Parking brake | Parking brake cable assembly No.3 to Body | 5 | 4 |
|
suspension torque settings
Save to email ✉️Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
---|---|---|---|---|---|---|
Wheels | Front wheel to Front axle | 103 | 76 |
|
||
Wheels | Rear lugnuts | 149 | 110 |
|
||
Struts | Front lower strut bolts | 225 | 166 |
|
||
Struts | Rear strut lower bolts | 142 | 105 |
|
||
Struts | Front upper strut nuts | 39 | 29 |
|
||
Struts | Rear strut upper nuts | 39 | 29 |
|
||
Shock absorbers/shocks | Flexible hose and speed sensor wire harness to Shock absorber | 29 | 21 | TMC/TMMT made |
|
|
Shock absorbers/shocks | Flexible hose and speed sensor wire harness to Shock absorber | 19 | 14 | TMUK made |
|
|
Stabilizer bar | Front stabilizer frame bolt | 34 | 25 |
|
||
Sway bar links/Stabilizer links | Stabilizer bar link set nut | 44 | 32 | TMUK/TMMT made |
|
|
Sway bar links/Stabilizer links | Stabilizer bar link set nut | 74 | 55 | TMC made |
|
|
Control arm | Front lower arm frame bolts | 137 | 101 |
|
||
Control arm | Rear control arms | 183 | 135 |
|
||
Ball joint | Front lower ball joint to Arm | 90 | 66 |
|
||
Ball joint | Front lower ball joint to Knuckle nut | 103 | 76 |
|
general torque settings
Save to email ✉️Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to |
---|
Did you find the answer to your specific question?
👍 0 👎 0