Toyota Camry XV20 (1996-2002) Torque Spec Settings
Below you'll find the tightening torques for the Toyota Camry XV20 in both Nm and ft/lbs. The first table contains the most-used torque settings. The tables after it contain all torque spec values I could find.
Most-used torque specs for Toyota Camry XV20
Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
---|---|---|---|---|---|---|
Wheels | Front wheel | 103 | 76 |
|
To make sure these are the correct tightening torque values, you can use the data below to verify this is the right model.
Are these torque settings right for you?
- Production years: 1996 - 2002
- Generation: 2
- Type of van: car
- Model variant: Base
- Also known as:
All Torque Settings in Tables
engine torque settings
Save to email ✉️Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
---|---|---|---|---|---|---|
Oil pan | Oil pan to Drain plug | 37 | 27 |
|
||
Oil pan | No.2 oil pan to Drain plug | 45 | 33 |
|
||
Oil pan | Oil pan to Cylinder block | 5 | 4 |
|
||
Oil pan | No.1 oil pan to Cylinder block | 20 | 15 |
|
||
Oil pan | No.2 oil pan to No.1 oil pan | 8 | 6 |
|
||
Oil pan | Oil pan to Oil pump | 5 | 4 |
|
||
Oil pan | No.1 oil pan to Oil pump | 8 | 6 | 10mm head |
|
|
Oil pan | No.1 oil pan to Oil pump | 20 | 15 | 12mm head |
|
|
Oil pan | No.1 oil pan to Rear oil seal retainer | 8 | 6 |
|
||
Oil pan | No.1 oil pan to Transaxle | 37 | 27 |
|
||
Oil pan | Oil pan baffle plate to No.1 oil pan | 8 | 6 |
|
||
Oil filter | Oil filter union to Cylinder block | 30 | 22 |
|
||
Oil filter | Oil strainer to Engine balancer | 5 | 4 |
|
||
Oil filter | Oil strainer to Main bearing cap | 8 | 6 |
|
||
Oil pressure switch | Oil pressure switch to Cylinder block | 13 | 10 |
|
||
Oil dipstick | Oil dipstick guide to LH cylinder head | 8 | 6 |
|
||
Oil pump | Oil pump to Cylinder block | 9 | 7 |
|
||
Oil pump | Oil pump to Cylinder block | 8 | 6 | 10mm head |
|
|
Oil pump | Oil pump to Cylinder block | 20 | 15 | 12mm head |
|
|
Oil pump | Oil pump body cover to Oil pump body | 9 | 7 |
|
||
Oil pump | Oil pump pulley to Oil pump drive shaft | 24 | 18 |
|
||
Oil pump | Oil pump to Relief valve plug | 37 | 27 |
|
||
Oil pump | Oil strainer to Oil pump | 5 | 4 |
|
||
Oil pump | Oil strainer to Oil pump | 8 | 6 |
|
||
Oil pump | Timing belt plate to Oil pump | 8 | 6 |
|
||
Oil pump | Oil pump pickup tube | 11 | 8 |
|
||
Piston rods | Connecting rod cap to Connecting rod | 25 | 18 | Step 1 |
|
|
Piston rods | Connecting rod cap to Connecting rod | 25 | 18 | Step 1 |
|
|
Cylinder head | Cylinder head to Cylinder block | 49 | 36 | Step 1 |
|
|
Cylinder head | Cylinder head to Cylinder block | 54 | 40 | 12 pointed head bolt, Step 1 |
|
|
Cylinder head | Cylinder head to Cylinder block | 19 | 14 | Recessed head bolt |
|
|
Cylinder head | Water bypass pipe to Cylinder head | 19 | 14 |
|
||
Cylinder head | Water outlet to Cylinder head | 15 | 11 |
|
||
Cylinder head | Water inlet pipe to LH cylinder head | 20 | 15 |
|
||
Cylinder head | LH engine hanger to Cylinder head | 25 | 18 |
|
||
Cylinder head | No.1 engine hanger to RH cylinder head | 39 | 29 |
|
||
Cylinder head | Delivery pipe to Cylinder head | 13 | 10 |
|
||
Cylinder head | Cylinder head cover to Cylinder head | 44 | 32 |
|
||
Cylinder head | Cylinder head cover to Cylinder head | 8 | 6 |
|
||
Cylinder head | Cylinder head rear plate to LH cylinder head | 8 | 6 |
|
||
Spark plugs | Spark plug to Cylinder head | 18 | 13 |
|
||
Spark plugs | Spark plug to Cylinder head | 18 | 13 |
|
||
Spark plugs | Spark plug tube to Cylinder head | 49 | 36 |
|
||
Intake manifold | Intake manifold to Cylinder head | 19 | 14 |
|
||
Intake manifold | Intake manifold to Cylinder head | 15 | 11 |
|
||
Intake manifold | Intake manifold stay to Intake manifold | 39 | 29 |
|
||
Intake manifold | No.2 intake manifold stay to Intake manifold | 42 | 31 |
|
||
Intake manifold | Intake manifold stay to Stiffening plate | 39 | 29 |
|
||
Intake manifold | No.2 intake manifold stay to Cylinder head | 21 | 15 |
|
||
Intake manifold | Water outlet to Intake manifold | 15 | 11 |
|
||
Intake manifold | Air intake chamber to Intake manifold | 43 | 32 |
|
||
Intake manifold | Intake air control valve to Air intake chamber | 15 | 11 |
|
||
Intake manifold | Air intake chamber stay to Air intake chamber | 20 | 15 |
|
||
Intake manifold | Air intake chamber stay to RH cylinder head | 20 | 15 |
|
||
Intake manifold | No.1 engine hanger to Air intake chamber | 39 | 29 |
|
||
Intake manifold | Delivery pipe to Intake manifold | 10 | 7 |
|
||
Throttle body | Throttle body to Intake manifold | 19 | 14 |
|
||
Throttle body | Throttle body to Air intake chamber | 20 | 15 |
|
||
Engine block | Cylinder block to Drain plug | 25 | 18 |
|
||
Engine block | Engine coolant drain union to Cylinder block | 39 | 29 |
|
||
Engine block | RH engine drain plug to EGR cooler | 7 | 5 |
|
||
Engine block | LH engine drain plug to Union on cylinder block | 13 | 10 |
|
||
Engine block | Water seal plate to Cylinder block | 18 | 13 |
|
||
Engine block | Water inlet housing to Cylinder block | 8 | 6 |
|
||
Engine block | No.1 rear end plate to Cylinder block | 9 | 7 |
|
||
Engine block | No.2 rear end plate to Cylinder block | 9 | 7 |
|
||
Engine block | RH stiffener plate to Cylinder block | 39 | 29 |
|
||
Engine block | Engine balancer to Cylinder block | 49 | 36 |
|
||
Engine block | Rear oil seal retainer to Cylinder block | 13 | 10 |
|
||
Engine block | Rear oil seal retainer to Cylinder block | 8 | 6 |
|
||
Engine mounts | Motor mount (Engine side) | 80 | 59 |
|
||
Engine mounts | Motor mount (Frame side) | 48 | 35 |
|
||
Engine mounts | RH engine mounting bracket to Cylinder block | 28 | 21 |
|
||
Engine mounts | No.2 RH engine mounting bracket to Cylinder block | 52 | 38 |
|
||
Engine mounts | No.2 RH engine mounting bracket to Generator bracket | 52 | 38 |
|
||
Engine mounts | No.2 generator bracket to Engine RH mounting bracket | 28 | 21 |
|
||
Engine mounts | RH engine mounting stay to Water outlet | 32 | 24 |
|
||
Engine mounts | RH engine mounting stay to Engine moving control rod | 32 | 24 |
|
||
Engine mounts | RH engine mounting stay to No.2 RH engine mounting bracket | 32 | 24 |
|
||
Engine mounts | No.2 RH engine mounting stay to No.2 generator bracket | 64 | 47 |
|
||
Engine mounts | No.2 RH engine mounting stay to No.2 RH engine mounting bracket | 64 | 47 |
|
||
Engine mounts | Front engine mounting insulator to Cylinder block | 64 | 47 |
|
||
Engine mounts | Front engine mounting insulator to Cylinder block | 64 | 47 |
|
||
Engine mounts | Rear engine mounting insulator to Cylinder block | 64 | 47 |
|
||
Engine mounts | Rear engine mounting insulator to Cylinder block | 64 | 47 |
|
||
Engine mounts | Engine moving control rod to No.2 RH engine mounting bracket | 64 | 47 |
|
||
Engine mounts | Engine moving control rod to RH engine mounting bracket | 64 | 47 |
|
||
Engine mounts | Engine moving control rod to Body | 64 | 47 |
|
||
Engine mounts | Engine moving control rod to RH fender apron | 64 | 47 |
|
||
Engine mounts | Front engine mounting insulator to Front frame | 80 | 59 | TMC made |
|
|
Engine mounts | Front engine mounting insulator to Front frame | 80 | 59 | TMC made |
|
|
Engine mounts | Front engine mounting insulator to Front frame | 44 | 32 | TMMK made for silver color |
|
|
Engine mounts | Front engine mounting insulator to Front frame | 44 | 32 | TMMK made for silver color |
|
|
Engine mounts | Front engine mounting insulator to Front frame | 66 | 49 | TMMK made for green color |
|
|
Engine mounts | Front engine mounting insulator to Front frame | 66 | 49 | TMMK made for green color |
|
|
Engine mounts | Rear engine mounting insulator to Front frame | 66 | 49 |
|
||
Engine mounts | Rear engine mounting insulator to Front frame | 66 | 49 |
|
||
Engine mounts | LH engine mounting insulator to Front frame | 80 | 59 |
|
||
Engine mounts | LH engine mounting insulator to Transaxle | 64 | 47 |
|
||
Engine mounts | LH engine mounting insulator to Transaxle | 64 | 47 |
|
||
Engine mounts | Engine mounting absorber to Front frame | 48 | 35 |
|
||
Engine mounts | Engine mounting absorber to Transaxle | 48 | 35 |
|
||
Sensor | Knock sensor 1 to Cylinder block | 44 | 32 |
|
||
Sensor | Knock sensor to Cylinder block | 39 | 29 |
|
||
Sensor | Oxygen sensor (bank 1 sensor 1) to Exhaust manifold | 44 | 32 |
|
||
Sensor | Oxygen sensor (bank 1 sensor 2) to Front exhaust pipe | 44 | 32 |
|
||
Sensor | Heated oxygen sensor (bank 1, 2 sensor 1) to Exhaust manifold | 44 | 32 |
|
||
Sensor | Heated oxygen sensor (bank 1 sensor 2) to Exhaust pipe | 44 | 32 |
|
||
Sensor | EGR valve position sensor to EGR valve | 2 | 1 |
|
||
Sensor | EGR gas temperature sensor to EGR valve | 20 | 15 |
|
||
Sensor | A/F sensor to Exhaust manifold | 44 | 32 |
|
||
Sensor | A/F sensor to Exhaust manifold | 44 | 32 |
|
||
Sensor | ECT sensor to Water outlet | 20 | 15 |
|
||
Sensor | Camshaft position sensor assembly to Cylinder head | 10 | 7 |
|
||
Sensor | Camshaft position sensor to Cylinder head | 8 | 6 |
|
||
Sensor | Crankshaft position sensor to Oil pump | 10 | 7 |
|
||
Sensor | Crankshaft position sensor to Oil pump | 8 | 6 |
|
||
Sensor | Front speed sensor installation bolt | 8 | 6 |
|
||
Sensor | Rear speed sensor installation bolt | 8 | 6 |
|
||
Alternator | Alternator to Engine | 24 | 18 |
|
||
Alternator | RH engine hanger to Generator bracket | 25 | 18 |
|
||
Alternator | Generator to Generator bracket | 52 | 38 |
|
||
Alternator | Generator to Generator bracket | 56 | 41 |
|
||
Alternator | Generator bracket to Cylinder head | 42 | 31 |
|
||
Alternator | Generator bracket to Cylinder block | 43 | 32 |
|
||
Alternator | Generator pulley to Rotor | 111 | 82 |
|
||
Alternator | Generator pulley to Rotor | 111 | 82 |
|
||
Alternator | Generator drive belt adjusting bar to Cylinder block | 22 | 16 |
|
||
Alternator | Generator to Adjusting bar | 18 | 13 |
|
||
Alternator | Generator to Adjusting bar | 18 | 13 |
|
||
Starter | Starter mounting bolt | 37 | 27 |
|
||
Starter | Starter mounting bolt | 45 | 33 |
|
||
Starter | Starter housing to Magnetic switch | 6 | 4 |
|
||
Starter | Starter housing to Magnetic switch | 6 | 4 |
|
||
Starter | Lead wire to Terminal C of starter | 6 | 4 |
|
||
Starter | Lead wire to Terminal C of starter | 6 | 4 |
|
||
Starter | Terminal nut to Terminal C of starter | 17 | 13 |
|
||
Starter | Terminal nut to Terminal C of starter | 17 | 13 |
|
||
Starter | Terminal nut to Terminal 30 of starter | 17 | 13 |
|
||
Starter | Terminal nut to Terminal 30 of starter | 17 | 13 |
|
||
Battery | Oil pan to Drain plug | 37 | 27 |
|
||
Battery | No.2 oil pan to Drain plug | 45 | 33 |
|
||
Camshaft | Camshaft timing pulley to Camshaft | 54 | 40 |
|
||
Camshaft | Camshaft timing pulley to Camshaft | 37 | 27 | For use with SST |
|
|
Camshaft | Camshaft timing pulley to Camshaft | 125 | 92 |
|
||
Camshaft | Camshaft timing pulley to Camshaft | 88 | 65 | For SST |
|
|
Camshaft | Camshaft sprocket bolts | 45 | 33 |
|
||
Camshaft | Camshaft bearing cap to Cylinder head | 19 | 14 |
|
||
Camshaft | Camshaft bearing cap to Cylinder head | 16 | 12 |
|
||
Crankshaft | Crankshaft position sensor | 11 | 8 |
|
||
Crankshaft | Crankshaft pulley to Crankshaft | 108 | 80 |
|
||
Crankshaft | Crankshaft pulley to Crankshaft | 215 | 159 |
|
||
Crankshaft | Main bearing cap to Cylinder block | 59 | 44 |
|
||
Crankshaft | Main bearing cap to Cylinder block | 22 | 16 | 12 pointed head bolt, Step 1 |
|
|
Crankshaft | Main bearing cap to Cylinder block | 27 | 20 | 6 pointed head bolt |
|
|
Crankshaft | Main cap side bolts | 27 | 20 |
|
||
Common rail | Fuel rail | 11 | 8 |
|
||
Water pump | Water pump to Water pump cover and cylinder block | 9 | 7 |
|
||
Water pump | Water pump to Cylinder block | 8 | 6 |
|
||
Water pump | Water bypass pipe to Water pump cover | 9 | 7 |
|
||
Water pump | Water inlet to Water pump cover | 9 | 7 |
|
||
Fuel/Oil cooler | Oil cooler pipe to Oil cooler | 15 | 11 |
|
||
Fuel/Oil cooler | Oil cooler to Cylinder block union bolt | 79 | 58 |
|
||
Fuel/Oil cooler | Oil cooler to Cylinder block nut | 9 | 7 |
|
||
Radiator | Upper radiator support to Body | 13 | 10 |
|
||
Radiator | Radiator support to Body | 13 | 10 |
|
||
Radiator | Electric cooling fan to Radiator | 5 | 4 |
|
||
Radiator | No.1 cooling fan shroud to Radiator | 5 | 4 |
|
||
Radiator | No.2 cooling fan shroud to Radiator | 5 | 4 |
|
||
Radiator | Oil cooler to Radiator lower tank | 8 | 6 |
|
||
Radiator | Radiator oil cooler to Radiator lower tank | 8 | 6 |
|
||
Radiator | Radiator inlet pipe to Radiator lower tank | 15 | 11 |
|
||
Radiator | Water inlet to Water inlet housing | 8 | 6 |
|
||
Air conditioning | A/C compressor to Cylinder block | 26 | 19 |
|
||
Air conditioning | A/C compressor housing bracket to Cylinder block | 25 | 18 |
|
||
Air conditioning | A/C compressor to Housing bracket | 25 | 18 |
|
||
Air conditioning | A/C compressor to No.1 oil pan | 25 | 18 |
|
||
Belt tensioner/Timing chains | Timing cover | 14 | 10 |
|
||
Belt tensioner/Timing chains | Timing chain guides | 19 | 14 |
|
||
Belt tensioner/Timing chains | Timing chain tensioner | 11 | 8 |
|
||
Belt tensioner/Timing chains | Belt tensioner | 69 | 51 |
|
||
Belt tensioner/Timing chains | Timing belt tensioner to Oil pump | 27 | 20 |
|
||
Belt tensioner/Timing chains | No.1 timing belt cover to Oil pump | 9 | 7 |
|
||
Belt tensioner/Timing chains | No.2 timing belt cover to No.3 timing belt cover | 9 | 7 |
|
||
Belt tensioner/Timing chains | No.3 timing belt cover to Cylinder head | 8 | 6 |
|
||
Belt tensioner/Timing chains | No.3 timing belt cover to Cylinder head | 9 | 7 |
|
||
Belt tensioner/Timing chains | No.1 idler pulley to Cylinder head | 42 | 31 |
|
||
Belt tensioner/Timing chains | No.2 idler pulley to Oil pump | 42 | 31 |
|
||
Belt tensioner/Timing chains | No.1 idler pulley to Oil pump | 34 | 25 |
|
||
Belt tensioner/Timing chains | No.2 idler pulley to No.2 idler pulley bracket | 43 | 32 |
|
||
Belt tensioner/Timing chains | No.2 idler pulley to Cylinder block | 28 | 21 |
|
||
Fuel system | Fuel inlet hose to Delivery pipe | 34 | 25 |
|
||
Fuel system | Fuel inlet hose to Delivery pipe | 29 | 21 | For use with SST |
|
|
Fuel system | Fuel inlet hose to Fuel filter | 29 | 21 |
|
||
Fuel system | Fuel inlet hose to Fuel filter | 29 | 21 |
|
||
Fuel system | Fuel line | 29 | 21 | Union bolt type |
|
|
Fuel system | Fuel line | 28 | 21 | Flare nut type, For use with SST |
|
|
Fuel system | Fuel line | 29 | 21 | Union bolt type |
|
|
Fuel system | Fuel line | 28 | 21 | Flare nut type, Using SST |
|
|
Fuel system | No.1 fuel pipe to Intake manifold | 20 | 15 |
|
||
Fuel system | Fuel pump assembly to Fuel tank | 4 | 3 |
|
||
Fuel system | Fuel pump assembly to Fuel tank | 4 | 3 |
|
||
Fuel system | Fuel filter to Fuel pump bracket | 2 | 1 |
|
||
Fuel system | Fuel filter to Fuel pump bracket | 2 | 1 |
|
||
Fuel system | Fuel pressure regulator to Fuel pump bracket | 2 | 1 |
|
||
Fuel system | Fuel pressure regulator to Fuel pump bracket | 2 | 1 |
|
||
Fuel system | Fuel tank band to Body | 39 | 29 |
|
||
Fuel system | Fuel tank band to Body | 39 | 29 |
|
drivetrain torque settings
Save to email ✉️Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
---|---|---|---|---|---|---|
Differential | Ring gear to Differential case | 83 | 61 |
|
||
Differential | Differential side bearing retainer | 18 | 13 |
|
||
Wheel hub assembly | Front hub nut | 103 | 76 |
|
||
Wheel hub assembly | Rear hub nut | 103 | 76 |
|
||
Wheel hub assembly | Rear axle hub bearing set bolt | 80 | 59 |
|
||
Clutch assembly | Clutch line | 15 | 11 |
|
||
Clutch assembly | Clutch line bracket to Transaxle bolt | 12 | 9 | Bolt A |
|
|
Clutch assembly | Clutch line bracket to Transaxle bolt | 7 | 5 | Bolt B |
|
|
Clutch assembly | Master cylinder installation nut | 12 | 9 |
|
||
Clutch assembly | Release cylinder installation bolt | 12 | 9 |
|
||
Clutch assembly | Clutch release cylinder to Transaxle | 12 | 9 |
|
||
Clutch assembly | Bleeder plug | 8 | 6 |
|
||
Clutch assembly | Clutch accumulator installation bolt | 21 | 15 |
|
||
Clutch assembly | Clutch accumulator installation nut | 27 | 20 |
|
||
Clutch assembly | Release fork support | 47 | 35 |
|
||
Clutch assembly | Release fork support | 39 | 29 |
|
||
Clutch assembly | Clutch release fork support | 39 | 29 |
|
||
Flywheel/Flex plate | Flywheel to Crankshaft | 88 | 65 |
|
||
Flywheel/Flex plate | Flywheel to Crankshaft | 83 | 61 |
|
||
Flywheel/Flex plate | Flywheel housing under cover to Transaxle | 8 | 6 |
|
||
Flywheel/Flex plate | Clutch cover to Flywheel | 19 | 14 |
|
||
Flywheel/Flex plate | Drive plate to Crankshaft | 83 | 61 |
|
||
Flywheel/Flex plate | Drive plate to Crankshaft | 83 | 61 |
|
||
Transmission fluid pan | Filler and drain plugs | 49 | 36 |
|
||
Transmission mount/case | Transaxle to Cylinder block | 46 | 34 | 14mm head |
|
|
Transmission mount/case | Transaxle to Cylinder block | 64 | 47 | 17mm head |
|
|
Transmission mount/case | Transaxle to Cylinder block | 66 | 49 |
|
||
Transmission mount/case | Transaxle to Engine | 46 | 34 | 14mm head |
|
|
Transmission mount/case | Transaxle to Engine | 64 | 47 | 17mm head |
|
|
Transmission mount/case | Engine mount bracket to Transaxle | 52 | 38 |
|
||
Transmission mount/case | RH stiffener plate to Transaxle | 39 | 29 |
|
||
Transmission mount/case | LH stiffener plate to Transaxle | 37 | 27 |
|
||
Transmission mount/case | LH stiffener plate to Transaxle | 42 | 31 |
|
||
Transmission mount/case | Transaxle case receiver set bolt | 7 | 5 |
|
||
Transmission mount/case | Transmission case to Transaxle case | 29 | 21 |
|
||
Transmission mount/case | Transmission case to Case cover | 29 | 21 |
|
||
Transmission mount/case | Transmission case protector | 18 | 13 |
|
||
Transmission mount/case | Selecting bellcrank to Transmission case | 37 | 27 |
|
||
Torque converter | Drive plate to Torque converter clutch | 27 | 20 |
|
||
Transfer | Shift lever assembly to Body | 12 | 9 |
|
||
Transfer | Shift cable grommet retainer to Body | 5 | 4 |
|
||
Transfer | Control shaft cover | 37 | 27 |
|
||
Transfer | Control shift lever to Lever shaft | 6 | 4 |
|
||
Transfer | Reverse shift arm bracket | 18 | 13 |
|
||
Transfer | No.3 shift fork to Shift fork shaft | 18 | 13 |
|
||
Drive/Axle shaft | Front axle hub to Drive shaft | 294 | 217 |
|
||
Drive/Axle shaft | Front drive shaft center bearing lock bolt | 32 | 24 |
|
steering torque settings
Save to email ✉️Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
---|---|---|---|---|---|---|
Tie rod end | Inner tie rod end | 68 | 50 |
|
||
Tie rod end | Outer tie rod end | 49 | 36 |
|
||
Tie rod end | Front tie rod end lock nut | 74 | 55 |
|
||
Steering knuckle | Front steering knuckle to Tie rod end | 49 | 36 |
|
||
Steering rack | Power steering gear assembly set bolt and nut | 181 | 133 |
|
||
Steering rack | Rack to Rack end | 60 | 44 |
|
||
Steering rack | Rack to Rack end | 83 | 61 | For use without SST |
|
|
Steering rack | Rack guide spring cap lock nut | 50 | 37 |
|
||
Steering rack | Rack guide spring cap lock nut | 69 | 51 | For use without SST |
|
|
Steering rack | Rack housing cap | 59 | 44 |
|
||
Steering column | Steering column assembly set nut | 25 | 18 |
|
||
Steering column | Turn signal bracket to Column tube | 7 | 5 |
|
||
Steering column | Lower column tube attachment to Column tube | 19 | 14 |
|
||
Steering shaft | Steering column assembly to Intermediate shaft assembly | 35 | 26 |
|
||
Steering shaft | Intermediate shaft assembly to Control valve shaft | 35 | 26 |
|
||
Steering wheel | Steering wheel set nut | 35 | 26 |
|
||
Steering wheel | Steering wheel pad set screw | 7 | 5 | Torx screw |
|
|
Power steering | Power steering pump to Power steering pump bracket | 43 | 32 |
|
||
Power steering | Power steering pump to Power steering pump bracket | 43 | 32 |
|
||
Power steering | Power steering pump bracket to Cylinder block | 43 | 32 |
|
||
Power steering | Power steering pump bracket to RH cylinder head | 43 | 32 |
|
||
Power steering | Power steering pump drive belt adjusting strut to Power steering pump | 43 | 32 |
|
||
Power steering | Power steering pump drive belt adjusting strut to Oil pump | 43 | 32 |
|
||
Power steering | Clamp plate set nut | 10 | 7 |
|
||
Power steering | Clamp plate set nut | 8 | 6 |
|
||
Power steering | PS vane pump set bolt | 29 | 21 | A bolt |
|
|
Power steering | PS vane pump set bolt | 43 | 32 | A bolt, For use without SST |
|
|
Power steering | PS vane pump set bolt | 43 | 32 | B bolt |
|
|
Power steering | Union bolt to Pressure feed tube | 52 | 38 |
|
||
Power steering | Vane pump pulley set nut | 43 | 32 |
|
||
Power steering | Front bracket to Rear bracket | 43 | 32 |
|
||
Power steering | Suction port union set bolt | 13 | 10 |
|
||
Power steering | Pressure port union | 83 | 61 |
|
||
Power steering | Rear housing set bolt | 24 | 18 |
|
exhaust torque settings
Save to email ✉️Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
---|---|---|---|---|---|---|
Exhaust manifold | Exhaust manifold to Cylinder head | 49 | 36 |
|
||
Exhaust manifold | Exhaust manifold to Cylinder head | 49 | 36 |
|
||
Exhaust manifold | No.1 exhaust manifold stay to Exhaust manifold | 42 | 31 |
|
||
Exhaust manifold | Exhaust manifold stay to Exhaust manifold | 20 | 15 |
|
||
Exhaust manifold | Exhaust manifold stay to Exhaust manifold | 20 | 15 | Except California |
|
|
Exhaust manifold | Exhaust manifold stay to Exhaust manifold | 34 | 25 |
|
||
Exhaust manifold | Exhaust manifold stay to Exhaust manifold | 34 | 25 | Except California |
|
|
Exhaust manifold | No.1 exhaust manifold stay to Transaxle | 42 | 31 |
|
||
Exhaust manifold | Exhaust manifold stay to Transmission housing | 20 | 15 | Except California |
|
|
Exhaust manifold | Exhaust manifold stay to Transmission housing | 34 | 25 |
|
||
Exhaust manifold | No.2 exhaust manifold stay to Exhaust manifold | 42 | 31 |
|
||
Exhaust manifold | No.2 exhaust manifold stay and LH stiffener plate to Cylinder block | 58 | 43 | TMC made |
|
|
Exhaust manifold | No.2 exhaust manifold stay and LH stiffener plate to Cylinder block | 42 | 31 | TMMK made |
|
|
Exhaust manifold | Exhaust pipe bracket to No.1 oil pan | 21 | 15 |
|
||
Exhaust manifold | Exhaust pipe bracket and No.2 rear end plate to Transaxle | 19 | 14 |
|
||
Exhaust manifold | Exhaust pipe bracket bolt | 19 | 14 |
|
||
Exhaust manifold | Exhaust pipe bracket nut | 33 | 24 |
|
||
Exhaust manifold | Front exhaust pipe to Exhaust manifold | 62 | 46 |
|
||
Exhaust manifold | Front exhaust pipe to Exhaust manifold | 62 | 46 |
|
||
Exhaust manifold | Front exhaust pipe to Center exhaust pipe | 56 | 41 |
|
||
Exhaust manifold | Front exhaust pipe to Center exhaust pipe | 56 | 41 |
|
||
Exhaust manifold | Center exhaust pipe to Tailpipe | 56 | 41 |
|
||
Exhaust manifold | Center exhaust pipe to Tailpipe | 56 | 41 |
|
||
Exhaust manifold | Support bracket for front exhaust pipe to Exhaust pipe bracket on No.2 rear end plate | 33 | 24 |
|
||
Exhaust manifold | Support bracket for front exhaust pipe to Front frame | 33 | 24 |
|
||
Exhaust manifold | Front exhaust pipe bracket to Sub frame | 33 | 24 |
|
||
Exhaust manifold | Support bracket for center exhaust pipe to Body | 19 | 14 |
|
||
Exhaust manifold | Support bracket for tailpipe to Body | 33 | 24 |
|
||
Exhaust manifold | Front exhaust pipe support bracket to No.1 oil pan | 21 | 15 |
|
||
Exhaust manifold | Support stay for front exhaust pipe to Support bracket | 33 | 24 |
|
||
Exhaust manifold | Front exhaust pipe support bracket to Front exhaust pipe stay | 33 | 24 |
|
||
EGR | EGR valve to Intake manifold | 13 | 10 |
|
||
EGR | EGR valve to Air intake chamber | 12 | 9 |
|
||
EGR | EGR valve to EGR pipe | 10 | 7 |
|
||
EGR | EGR pipe to EGR valve | 12 | 9 |
|
||
EGR | EGR cooler to Cylinder block | 9 | 7 |
|
||
EGR | EGR pipe to EGR cooler | 12 | 9 |
|
||
EGR | EGR pipe to Cylinder head | 61 | 45 |
|
||
EGR | No.1 EGR pipe to EGR cooler | 12 | 9 |
|
||
EGR | No.1 EGR pipe to RH exhaust manifold | 12 | 9 |
|
||
EGR | No.2 EGR pipe to Air intake chamber | 12 | 9 |
|
||
EGR | No.2 EGR pipe to EGR cooler | 12 | 9 |
|
brakes torque settings
Save to email ✉️Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
---|---|---|---|---|---|---|
Disc brake | Front brake torque plate to Steering knuckle | 107 | 79 |
|
||
Disc brake | Rear brake torque plate to Rear axle carrier | 47 | 35 |
|
||
Disc brake | Front brake caliper installation bolt | 34 | 25 |
|
||
Disc brake | Rear brake caliper installation bolt | 20 | 15 |
|
||
Disc brake | Rear drum brake wheel cylinder to Backing plate | 10 | 7 |
|
||
Disc brake | Bleeder plug | 8 | 6 |
|
||
Disc brake | Front steering knuckle to Disc brake dust cover | 8 | 6 |
|
||
Brake line | Front brake caliper to Flexible hose | 29 | 21 |
|
||
Brake line | Rear brake caliper to Flexible hose | 29 | 21 |
|
||
Brake line | Brake line union nut | 15 | 11 | 10mm nut |
|
|
Brake line | Brake line union nut | 20 | 15 | 12mm nut |
|
|
Brake booster | Brake booster clevis lock nut | 25 | 18 |
|
||
Brake booster | Brake booster to Pedal bracket | 13 | 10 |
|
||
Brake pedal | Brake pedal to Pedal bracket | 39 | 29 |
|
||
Brake pedal | Pedal bracket to Instrument panel reinforcement | 13 | 10 |
|
||
Master cylinder | Master cylinder to Piston stopper bolt | 10 | 7 |
|
||
Master cylinder | Master cylinder to Reservoir | 2 | 1 |
|
||
Master cylinder | Master cylinder to Brake booster | 13 | 10 |
|
||
Parking brake | Parking brake cable set bolt | 5 | 4 |
|
||
Parking brake | Parking brake cable bracket to Backing plate | 8 | 6 |
|
||
ABS | Front ABS speed sensor set bolt | 8 | 6 |
|
||
ABS | Rear ABS speed sensor set bolt | 8 | 6 |
|
||
ABS | ABS actuator to Actuator bracket | 5 | 4 | DENSO type |
|
|
ABS | ABS actuator to Actuator bracket | 9 | 7 | BOSCH type |
|
|
ABS | ABS actuator to ECU | 3 | 2 | BOSCH type |
|
|
ABS | ABS & TRAC actuator to Actuator bracket | 5 | 4 |
|
||
ABS | ABS (& TRAC) actuator bracket to Body | 19 | 14 |
|
||
ABS | Front flexible hose and ABS speed sensor wire harness to Shock absorber | 29 | 21 |
|
||
ABS | Rear ABS speed sensor wire harness to Shock absorber | 6 | 4 |
|
suspension torque settings
Save to email ✉️Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
---|---|---|---|---|---|---|
Wheels | Front wheel | 103 | 76 |
|
||
Wheels | Rear lug nuts | 149 | 110 |
|
||
Struts | Upper strut nuts | 39 | 29 |
|
||
Struts | Lower strut bolts | 212 | 156 |
|
||
Struts | Rear strut upper nuts | 34 | 25 |
|
||
Struts | Rear strut lower bolts | 113 | 83 |
|
||
Shock absorbers/shocks | Front steering knuckle to Shock absorber | 211 | 156 |
|
||
Shock absorbers/shocks | Rear shock absorber to Rear axle carrier | 255 | 188 | New nut |
|
|
Shock absorbers/shocks | Rear shock absorber to Rear axle carrier | 196 | 145 | Reused nut |
|
|
Shock absorbers/shocks | Rear flexible hose to Shock absorber | 29 | 21 |
|
||
Stabilizer bar | Front stabilizer bar bracket to Suspension member | 19 | 14 |
|
||
Stabilizer bar | Rear stabilizer bar bracket to Suspension member | 19 | 14 |
|
||
Sway bar links/Stabilizer links | Front stabilizer bar link set bolt | 39 | 29 |
|
||
Sway bar links/Stabilizer links | Rear stabilizer bar link set nut | 39 | 29 |
|
||
Control arm | Front suspension member with lower suspension arm bolt | 181 | 133 | Bolt A |
|
|
Control arm | Front suspension member with lower suspension arm bolt | 32 | 24 | Bolt B |
|
|
Control arm | Front suspension member with lower suspension arm nut | 36 | 27 | Nut C |
|
|
Control arm | Rear lower suspension arm to Suspension member | 181 | 133 |
|
||
Control arm | Rear lower suspension arm to Rear axle carrier | 181 | 133 |
|
||
Control arm | Front lower suspension arm set bolt | 206 | 152 |
|
||
Control arm | Rear No.2 lower suspension arm lock nut | 56 | 41 |
|
||
Control arm | Rear control arms | 183 | 135 |
|
||
Ball joint | Front lower ball joint to Lower suspension arm | 127 | 94 |
|
||
Ball joint | Front lower ball joint to Steering knuckle | 123 | 91 |
|
general torque settings
Save to email ✉️Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to |
---|
Did you find the answer to your specific question?
👍 1 👎 0