Toyota Highlander XU50 (2013-2018) Torque Spec Settings
By SsmIntrigue - Own work, CC BY-SA 4.0
Below you'll find the tightening torques for the Toyota Highlander XU50 in both Nm and ft/lbs. The first table contains the most-used torque settings. The tables after it contain all torque spec values I could find.
Most-used torque specs for Toyota Highlander XU50
| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
|---|---|---|---|---|---|---|
| Oil pan | Oil drain plug | 37 | 27 |
|
|
|
| Spark plugs | Oil drain plug | 37 | 27 |
|
|
|
| Intake manifold | Intake manifold | 20 | 15 |
|
|
|
| Wheel hub assembly | Front axle nut | 294 | 217 |
|
|
To make sure these are the correct tightening torque values, you can use the data below to verify this is the right model.
Are these torque settings right for you?
- Production years: 2013 - 2018
- Generation: 3
- Type of van: car
- Model variant: Base
- Also known as:
All Torque Settings in Tables
engine torque settings
Save to email ✉️| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
|---|---|---|---|---|---|---|
| Oil pan | Oil drain plug | 37 | 27 |
|
|
|
| Oil pan | Oil pan | 10 | 7 | 10mm |
|
|
| Oil pan | Oil pan | 20 | 15 | 12mm |
|
|
| Oil pump | Oil pump | 11 | 8 |
|
|
|
| Oil pump | Oil pump pickup tube | 11 | 8 |
|
|
|
| Oil pump | Oil pump relief valve | 49 | 36 |
|
|
|
| Piston rods | Connecting rod | 24 | 18 | Step 1 |
|
|
| Cylinder head | Cylinder head | 37 | 27 | Step 1 |
|
|
| Cylinder head | Cylinder head | 30 | 22 | Extra bolts (14mm) |
|
|
| Spark plugs | Oil drain plug | 37 | 27 |
|
|
|
| Intake manifold | Intake manifold | 20 | 15 |
|
|
|
| Engine mounts | Motor mount to Engine | 80 | 59 |
|
|
|
| Engine mounts | Motor mount to Frame | 48 | 35 |
|
|
|
| Sensor | Crankshaft position sensor | 11 | 8 |
|
|
|
| Alternator | Alternator to Engine | 24 | 18 |
|
|
|
| Battery | Ignition coil | 7 | 5 |
|
|
|
| Camshaft | Camshaft sprockets | 100 | 74 |
|
|
|
| Camshaft | Camshaft bearing caps | 16 | 12 |
|
|
|
| Camshaft | Camshaft bearing cap No.1 | 24 | 18 |
|
|
|
| Crankshaft | Crankshaft pulley | 251 | 185 |
|
|
|
| Crankshaft | Main cap | 61 | 45 | Step 1 |
|
|
| Crankshaft | Main cap side bolts | 52 | 38 |
|
|
|
| Common rail | Fuel rail | 11 | 8 |
|
|
|
| Water pump | Water pump | 11 | 8 | 10mm |
|
|
| Water pump | Water pump | 20 | 15 | 12mm |
|
|
| Water pump | Water pump pulley | 20 | 15 |
|
|
|
| Coolant expansion tank | Intake surge tank | 29 | 21 |
|
|
|
| Common rail | Fuel rail | 11 | 8 |
|
|
|
| Air conditioning | A/C compressor to Engine | 22 | 16 |
|
|
|
| Belt tensioner/Timing chains | Timing cover | 20 | 15 |
|
|
|
| Belt tensioner/Timing chains | Timing chain idler gear | 60 | 44 |
|
|
|
| Belt tensioner/Timing chains | Timing chain guides | 19 | 14 |
|
|
|
| Belt tensioner/Timing chains | Timing chain tensioner | 19 | 14 |
|
|
|
| Belt tensioner/Timing chains | Belt tensioner | 37 | 27 |
|
|
|
| Belt tensioner/Timing chains | Idler pulley bolt | 41 | 30 |
|
|
|
| Valve cover | Valve cover | 11 | 8 |
|
|
drivetrain torque settings
Save to email ✉️| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
|---|---|---|---|---|---|---|
| Wheel hub assembly | Front axle nut | 294 | 217 |
|
|
|
| Wheel hub assembly | Rear axle nut | 216 | 159 |
|
|
|
| Wheel hub assembly | Front wheel hub | 103 | 76 |
|
|
|
| Wheel hub assembly | Rear wheel hub | 80 | 59 |
|
|
|
| Flywheel/Flex plate | Flywheel to Converter | 41 | 30 |
|
|
|
| Transmission fluid pan | Transmission drain plug | 20 | 15 |
|
|
|
| Transmission fluid pan | Transmission pan | 8 | 6 |
|
|
|
| Transmission mount/case | Bell housing bolts | 72 | 53 |
|
|
|
| Torque converter | Torque converter drain | 20 | 15 |
|
|
steering torque settings
Save to email ✉️| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
|---|---|---|---|---|---|---|
| Tie rod end | Outer tie rod | 49 | 36 |
|
|
|
| Tie rod end | Inner tie rod | 68 | 50 |
|
|
|
| Power steering | Power steering to Engine | 41 | 30 |
|
|
exhaust torque settings
Save to email ✉️| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
|---|---|---|---|---|---|---|
| Exhaust manifold | Exhaust manifold | 20 | 15 |
|
|
|
| Exhaust manifold | Exhaust pipe | 41 | 30 |
|
|
|
| EGR | EGR pipe | 19 | 14 |
|
|
brakes torque settings
Save to email ✉️| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
|---|---|---|---|---|---|---|
| Disc brake | Front brake caliper | 107 | 79 |
|
|
|
| Disc brake | Rear brake caliper | 34 | 25 |
|
|
|
| Disc brake | Front caliper banjo bolt | 30 | 22 |
|
|
|
| Disc brake | Rear caliper banjo bolt | 30 | 22 |
|
|
suspension torque settings
Save to email ✉️| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
|---|---|---|---|---|---|---|
| Wheels | Rear lugnut | 149 | 110 |
|
|
|
| Struts | Front strut upper nuts | 80 | 59 |
|
|
|
| Struts | Rear strut upper nut | 30 | 22 |
|
|
|
| Struts | Front strut lower bolts | 210 | 155 |
|
|
|
| Struts | Rear strut lower bolt | 115 | 85 |
|
|
|
| Stabilizer bar | Front swaybar bracket | 20 | 15 |
|
|
|
| Stabilizer bar | Rear swaybar brackets | 19 | 14 |
|
|
|
| Sway bar links/Stabilizer links | Front stabilizer endlink | 75 | 55 |
|
|
|
| Sway bar links/Stabilizer links | Rear swaybar endlinks | 39 | 29 |
|
|
|
| Control arm | Front lower arm frame bolts | 203 | 150 |
|
|
|
| Control arm | Rear control arms | 113 | 83 |
|
|
|
| Ball joint | Front lower ball joint to Arm | 128 | 94 |
|
|
|
| Ball joint | Front lower ball joint nut | 122 | 90 |
|
|
general torque settings
Save to email ✉️| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to |
|---|
By OSX - Own work, Public Domain
Did you find the answer to your specific question?
👍 1 👎 2
