Toyota Supra 4 (1994-1998) Torque Spec Settings
By Mr.choppers - Own work, CC BY-SA 3.0
Below you'll find the tightening torques for the Toyota Supra 4 in both Nm and ft/lbs. The first table contains the most-used torque settings. The tables after it contain all torque spec values I could find.
Most-used torque specs for Toyota Supra 4
| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
|---|---|---|---|---|---|---|
| Transmission fluid pan | Drain plug | 20 | 15 |
|
|
|
| Transmission fluid pan | Oil pan drain plug | 17 | 13 |
|
|
To make sure these are the correct tightening torque values, you can use the data below to verify this is the right model.
Are these torque settings right for you?
- Production years: 1994 - 1998
- Generation: 4
- Type of van: car
- Model variant: Base
All Torque Settings in Tables
engine torque settings
Save to email ✉️| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
|---|---|---|---|---|---|---|
| Oil filter | Oil separator to Intermediate plate | 18 | 13 |
|
|
|
| Engine mounts | Engine rear mounting to Transmission | 25 | 18 |
|
|
|
| Sensor | Oxygen sensor set nut | 18 | 13 |
|
|
|
| Starter | Transmission to Starter | 39 | 29 |
|
|
drivetrain torque settings
Save to email ✉️| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
|---|---|---|---|---|---|---|
| Clutch assembly | Clutch housing to Transmission case | 37 | 27 |
|
|
|
| Transmission fluid pan | Drain and filler plugs | 39 | 29 |
|
|
|
| Transmission mount/case | Transmission to Engine | 37 | 27 | 10mm bolt |
|
|
| Transmission mount/case | Transmission to Engine | 72 | 53 | 12mm bolt |
|
|
| Transmission mount/case | Extension housing to Intermediate plate | 37 | 27 |
|
|
|
| Transfer | Shift lever to Control shift lever arm | 8 | 6 |
|
|
|
| Transfer | Transmission shift lever to Transmission | 19 | 14 |
|
|
|
| Transfer | Control shift lever retainer to Extension housing | 18 | 13 |
|
|
|
| Transfer | Shift lever housing to Shift and select lever shaft | 39 | 29 |
|
|
|
| Transfer | Control shift lever arm to Control shift lever retainer | 25 | 18 |
|
|
|
| Transfer | Control shift lever arm to Extension housing | 19 | 14 |
|
|
|
| Transfer | Shift fork set bolt | 20 | 15 |
|
|
|
| Transfer | No.1 control shift yoke to Control shaft | 19 | 14 |
|
|
|
| Transfer | No.2 inner shift lever to Control shaft | 39 | 29 |
|
|
|
| Drive/Axle shaft | Propeller shaft to Differential | 93 | 69 |
|
|
|
| Drive/Axle shaft | Propeller shaft center bearing | 49 | 36 |
|
|
steering torque settings
Save to email ✉️| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to |
|---|
exhaust torque settings
Save to email ✉️| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
|---|---|---|---|---|---|---|
| Exhaust manifold | Exhaust No.2 front pipe to Exhaust front pipe | 43 | 32 |
|
|
|
| Exhaust manifold | Exhaust front pipe to Exhaust center pipe | 43 | 32 |
|
|
|
| Exhaust manifold | Exhaust center pipe to Tail pipe | 19 | 14 |
|
|
brakes torque settings
Save to email ✉️| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to |
|---|
suspension torque settings
Save to email ✉️| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to |
|---|
general torque settings
Save to email ✉️| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to |
|---|
By Mr.choppers - Own work, CC BY-SA 3.0
Did you find the answer to your specific question?
👍 0 👎 0
