Toyota Hilux 8 (2015-on) Torque Spec Settings
Below you'll find the tightening torques for the Toyota Hilux 8 in both Nm and ft/lbs. The first table contains the most-used torque settings. The tables after it contain all torque spec values I could find.
Most-used torque specs for Toyota Hilux 8
Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to |
---|
To make sure these are the correct tightening torque values, you can use the data below to verify this is the right model.
Are these torque settings right for you?
- Production years: 2015 - present
- Generation: 8
- Type of van: pickup
- Model variant: Base
- Also known as:
All Torque Settings in Tables
engine torque settings
Save to email ✉️Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
---|---|---|---|---|---|---|
Oil pan | Oil pan drain plug to Oil pan sub-assembly | 40 | 30 |
|
||
Oil pan | Oil pan sub-assembly to Cylinder block sub-assembly | 10 | 7 |
|
||
Oil pan | Oil pan cover silencer to Oil pan sub-assembly | 10 | 7 |
|
||
Oil filter | Oil filter sub-assembly to Oil filter bracket | 12 | 9 |
|
||
Oil pressure switch | Engine oil pressure switch assembly to Oil filter bracket | 10 | 7 |
|
||
Oil dipstick | Engine oil level dipstick guide to Intake manifold | 10 | 7 |
|
||
Cylinder head | Cylinder head cover sub-assembly to Cylinder head sub-assembly | 10 | 7 |
|
||
Intake manifold | Intake manifold to Cylinder head sub-assembly | 23 | 17 |
|
||
Intake manifold | Manifold stay to Intake manifold and cylinder block sub-assembly | 21 | 15 |
|
||
Intake manifold | Manifold stay to No.2 fuel pipe | 10 | 7 |
|
||
Intake manifold | Vacuum control valve set to Intake manifold | 10 | 7 |
|
||
Intake manifold | Engine wire bracket to Intake manifold | 19 | 14 |
|
||
Intake manifold | No.4 water by-pass pipe to Intake manifold | 10 | 7 |
|
||
Intake manifold | Mass air flow meter sub-assembly to Air cleaner cap sub-assembly | 1 | 1 |
|
||
Intake manifold | Air cleaner case sub-assembly to Body | 6 | 4 |
|
||
Intake manifold | Air cleaner case sub-assembly with air cleaner hose to Hose clamp | 4 | 3 |
|
||
Intake manifold | No.1 injection pipe clamp to Intake manifold | 10 | 7 |
|
||
Intake manifold | No.2 injection pipe clamp to Intake manifold | 10 | 7 |
|
||
Intake manifold | No.2 nozzle leakage pipe assembly to Intake manifold | 10 | 7 |
|
||
Throttle body | Diesel throttle body assembly to Intake manifold | 10 | 7 |
|
||
Throttle body | Intercooler air tube to Diesel throttle body assembly | 7 | 5 |
|
||
Throttle body | Fuel hose bracket to Diesel throttle body assembly | 7 | 5 |
|
||
Engine block | Cylinder block drain cock plug | 13 | 10 |
|
||
Engine mounts | No.1 engine cover sub-assembly to No.1 engine cover bracket and No.2 engine cover bracket | 21 | 15 |
|
||
Engine mounts | Engine cover bracket to Cylinder head sub-assembly | 21 | 15 |
|
||
Engine mounts | Pipe clamp to Engine cover bracket | 10 | 7 |
|
||
Sensor | Accelerator pedal sensor assembly to Body | 5 | 4 |
|
||
Sensor | Air fuel ratio sensor to Front exhaust pipe | 38 | 28 | With SST |
|
|
Sensor | Air fuel ratio sensor to Front exhaust pipe | 44 | 32 | Without SST |
|
|
Sensor | Engine coolant temperature sensor to Cylinder head sub-assembly | 20 | 15 |
|
||
Sensor | Intake air temperature sensor to Intercooler air tube | 29 | 21 |
|
||
Sensor | Diesel turbo pressure sensor to No.3 water by-pass pipe sub-assembly | 10 | 7 |
|
||
Sensor | Exhaust gas temperature sensor to Exhaust manifold converter sub-assembly | 30 | 22 |
|
||
Sensor | No.2 exhaust gas temperature sensor to Exhaust manifold converter sub-assembly | 30 | 22 |
|
||
Sensor | No.3 exhaust gas temperature sensor to Exhaust manifold converter sub-assembly | 30 | 22 |
|
||
Sensor | No.3 exhaust gas temperature sensor to No.1 vacuum pipe | 10 | 7 |
|
||
Sensor | Differential pressure sensor to Pipe clamp | 10 | 7 |
|
||
Sensor | Camshaft position sensor to Cylinder head cover sub-assembly | 10 | 7 |
|
||
Sensor | Crankshaft position sensor to Rear oil seal retainer | 10 | 7 |
|
||
Sensor | Engine oil level sensor to Oil pan sub-assembly | 12 | 9 |
|
||
Alternator | Generator assembly to Generator bracket | 8 | 6 |
|
||
Alternator | Generator assembly to Cylinder block | 43 | 32 |
|
||
Alternator | Retainer plate to Generator drive end frame | 2 | 1 |
|
||
Alternator | Generator coil assembly to Generator drive end frame | 6 | 4 |
|
||
Alternator | Generator brush holder assembly to Generator coil assembly | 2 | 1 |
|
||
Alternator | Generator rear end cover to Generator coil assembly | 5 | 4 |
|
||
Alternator | Generator pulley with clutch to Generator rotor assembly | 111 | 82 | For 80A type, Without SST |
|
|
Alternator | Generator pulley with clutch to Generator rotor assembly | 88 | 65 | For 80A type, With SST |
|
|
Alternator | Generator pulley with clutch to Generator rotor assembly | 80 | 59 | For 90A type |
|
|
Alternator | Generator wire to Terminal B | 10 | 7 |
|
||
Battery | Battery clamp sub-assembly to Battery clamp bolt | 5 | 4 |
|
||
Battery | Positive cable to Positive battery terminal | 5 | 4 |
|
||
Battery | Negative cable to Negative battery terminal | 5 | 4 |
|
||
Crankshaft | Crankshaft position sensor harness bracket to Cylinder block sub-assembly | 10 | 7 |
|
||
Common rail | Fuel inlet pipe sub-assembly to Common rail assembly | 40 | 30 | Without SST |
|
|
Common rail | Fuel inlet pipe sub-assembly to Common rail assembly | 31 | 23 | With SST |
|
|
Water pump | Engine water pump assembly to Cylinder block sub-assembly | 25 | 18 |
|
||
Water pump | Engine water pump assembly to Cylinder block sub-assembly | 13 | 10 |
|
||
Water pump | No.1 water by-pass pipe to Engine water pump assembly | 10 | 7 |
|
||
Water pump | No.2 water by-pass pipe sub-assembly to Engine water pump assembly and water inlet | 10 | 7 |
|
||
Water pump | Fluid coupling assembly to Engine water pump assembly | 23 | 17 |
|
||
Fuel/Oil cooler | Oil cooler assembly to Cylinder block sub-assembly | 15 | 11 |
|
||
Fuel/Oil cooler | Oil cooler tube bracket to Turbocharger stay | 14 | 10 |
|
||
Intercooler | No.2 air tube to Intercooler assembly | 7 | 5 |
|
||
Intercooler | No.4 air hose to No.2 air tube and intercooler air tube | 7 | 5 |
|
||
Radiator | Radiator assembly to Body | 22 | 16 |
|
||
Radiator | Radiator reservoir to Radiator assembly | 5 | 4 |
|
||
Radiator | Radiator reservoir vent plug | 2 | 1 |
|
||
Radiator | No.1 oil reservoir bracket to Radiator assembly and fan shroud | 5 | 4 |
|
||
Radiator | No.1 air tube to Radiator support assembly | 8 | 6 |
|
||
Radiator | No.2 air tube to Lower radiator support assembly | 8 | 6 |
|
||
Radiator | Intercooler assembly to Lower radiator support assembly | 8 | 6 |
|
||
Radiator | Hood lock support sub-assembly to Upper radiator support assembly | 13 | 10 |
|
||
Radiator | Fan to Fluid coupling assembly | 6 | 4 |
|
||
Radiator | Suction hose sub-assembly to Water inlet | 5 | 4 |
|
||
Belt tensioner/Timing chains | Timing chain case assembly and engine water pump assembly to Cylinder head sub-assembly and cylinder block sub-assembly | 25 | 18 | For bolts A, B and C |
|
|
Belt tensioner/Timing chains | Timing chain case assembly and engine water pump assembly to Cylinder head sub-assembly and cylinder block sub-assembly | 43 | 32 | For bolt D |
|
|
Belt tensioner/Timing chains | Timing chain cover sub-assembly to Timing chain case assembly | 21 | 15 |
|
||
Belt tensioner/Timing chains | Timing chain cover plate | 10 | 7 |
|
||
Belt tensioner/Timing chains | V-ribbed belt tensioner assembly to Timing chain cover sub-assembly | 21 | 15 |
|
||
Belt tensioner/Timing chains | No.1 idler pulley sub-assembly to Generator bracket sub-assembly | 43 | 32 |
|
||
PCM | No.1 ECM bracket to ECM | 3 | 2 |
|
||
PCM | No.2 ECM bracket to ECM | 3 | 2 |
|
||
PCM | No.1 ECM bracket to Body | 6 | 4 |
|
||
PCM | No.2 ECM bracket to Body | 8 | 6 |
|
||
Fuel system | Fuel inlet pipe sub-assembly to Fuel supply pump assembly | 48 | 35 | Without union nut wrench |
|
|
Fuel system | Fuel inlet pipe sub-assembly to Fuel supply pump assembly | 41 | 30 | With union nut wrench |
|
|
Fuel system | Injector holder to No.1 injector holder | 10 | 7 |
|
||
Fuel system | No.2 nozzle holder clamp to No.1 injector holder | 12 | 9 |
|
||
Fuel system | No.1 fuel pipe to Cylinder head cover sub-assembly | 10 | 7 |
|
||
Fuel system | No.1 fuel pipe to Injector holder | 26 | 19 |
|
||
Fuel system | No.3 fuel pipe to Supply pump assembly to Fuel filter | 42 | 31 | With DPF |
|
|
Fuel system | No.4 fuel pipe sub-assembly to Supply pump assembly to Fuel filter union bolt | 42 | 31 |
|
||
Fuel system | No.4 fuel pipe sub-assembly to Supply pump assembly to Fuel filter bolt | 10 | 7 |
|
drivetrain torque settings
Save to email ✉️Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to |
---|
steering torque settings
Save to email ✉️Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
---|---|---|---|---|---|---|
Power steering | Power steering oil pressure switch to Vane pump assembly | 21 | 15 |
|
exhaust torque settings
Save to email ✉️Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
---|---|---|---|---|---|---|
Exhaust manifold | Exhaust manifold to Cylinder head sub-assembly | 40 | 30 |
|
||
Exhaust manifold | Exhaust manifold stud bolt | 10 | 7 |
|
||
Exhaust manifold | Front exhaust pipe assembly to Exhaust manifold converter sub-assembly | 43 | 32 |
|
||
Exhaust manifold | Tailpipe assembly to Front exhaust pipe assembly | 43 | 32 |
|
||
Exhaust manifold | No.1 injector holder to Exhaust manifold | 43 | 32 |
|
||
Exhaust manifold | No.1 exhaust manifold heat insulator to Exhaust manifold | 12 | 9 | With DPF |
|
|
Exhaust manifold | No.1 exhaust manifold heat insulator to Exhaust manifold | 12 | 9 | Without DPF |
|
|
Exhaust manifold | No.2 exhaust manifold heat insulator to No.1 injector holder | 10 | 7 |
|
||
Turbo | Turbocharger sub-assembly to Exhaust manifold | 73 | 54 |
|
||
Turbo | Turbocharger nozzle vane control actuator to Compressor housing | 12 | 9 |
|
||
Turbo | Turbocharger stay to Turbocharger sub-assembly and cylinder block sub-assembly | 24 | 18 |
|
||
Turbo | Wire harness to Turbocharger stay | 19 | 14 |
|
||
Turbo | Turbo oil inlet pipe sub-assembly to Turbocharger sub-assembly and cylinder block sub-assembly nut | 13 | 10 |
|
||
Turbo | Turbo oil inlet pipe sub-assembly to Turbocharger sub-assembly and cylinder block sub-assembly union bolt | 36 | 27 |
|
||
Turbo | Turbo oil outlet pipe to Turbocharger sub-assembly | 12 | 9 |
|
||
Turbo | Turbo water pipe sub-assembly to Turbocharger sub-assembly | 13 | 10 |
|
||
Turbo | Compressor inlet elbow to Turbocharger sub-assembly | 21 | 15 |
|
||
Turbo | Compressor outlet elbow to Turbocharger sub-assembly | 21 | 15 |
|
||
Turbo | No.1 turbo insulator to Exhaust manifold and turbocharger sub-assembly | 12 | 9 | With DPF |
|
|
Turbo | No.1 turbo insulator to Exhaust manifold and turbocharger sub-assembly | 12 | 9 | Without DPF |
|
|
EGR | No.1 EGR pipe sub-assembly to Exhaust manifold and EGR valve adapter | 29 | 21 |
|
||
EGR | No.1 EGR pipe sub-assembly to Vacuum transmitting pipe sub-assembly | 10 | 7 |
|
||
EGR | No.3 water by-pass pipe sub-assembly to No.1 EGR cooler | 10 | 7 |
|
||
EGR | No.1 EGR cooler and No.2 EGR valve assembly to Intake manifold | 21 | 15 |
|
||
EGR | No.1 EGR cooler to No.2 EGR valve assembly | 25 | 18 |
|
||
EGR | No.2 EGR valve assembly stud bolt | 10 | 7 |
|
||
EGR | No.2 EGR valve assembly to No.1 EGR cooler | 25 | 18 |
|
||
EGR | EGR valve adapter to No.2 EGR valve assembly | 25 | 18 |
|
||
EGR | Electric EGR control valve assembly to No.2 EGR valve assembly | 25 | 18 |
|
||
EGR | No.2 EGR pipe to Electric EGR control valve assembly | 29 | 21 |
|
||
EGR | EGR valve bracket to Electric EGR control valve assembly | 21 | 15 |
|
||
Catalytic converter | Exhaust pipe clamp to Exhaust manifold converter sub-assembly | 18 | 13 | With DPF |
|
|
Catalytic converter | Exhaust pipe clamp to Exhaust manifold converter sub-assembly | 18 | 13 | Without DPF |
|
|
Catalytic converter | Exhaust pipe support stay to Cylinder block sub-assembly and exhaust manifold converter sub-assembly | 38 | 28 | With DPF |
|
|
Catalytic converter | Exhaust pipe support stay to Cylinder block sub-assembly and exhaust manifold converter sub-assembly | 38 | 28 | Without DPF |
|
|
Catalytic converter | No.2 exhaust pipe support stay t o Cylinder block sub-assembly and exhaust manifold converter sub-assembly | 38 | 28 | With DPF |
|
|
Catalytic converter | No.2 exhaust pipe support stay t o Cylinder block sub-assembly and exhaust manifold converter sub-assembly | 38 | 28 | Without DPF |
|
|
Catalytic converter | No.1 vacuum pipe to Exhaust manifold converter sub-assembly | 48 | 35 | With DPF |
|
|
Catalytic converter | No.2 vacuum pipe to Exhaust manifold converter sub-assembly | 48 | 35 | With DPF |
|
brakes torque settings
Save to email ✉️Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to |
---|
suspension torque settings
Save to email ✉️Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to |
---|
general torque settings
Save to email ✉️Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to |
---|
Did you find the answer to your specific question?
👍 2 👎 2