Toyota 4Runner 5 (2010-on) Torque Spec Settings
Below you'll find the tightening torques for the Toyota 4Runner 5 in both Nm and ft/lbs. The first table contains the most-used torque settings. The tables after it contain all torque spec values I could find.
Most-used torque specs for Toyota 4Runner 5
Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to |
---|
To make sure these are the correct tightening torque values, you can use the data below to verify this is the right model.
Are these torque settings right for you?
- Production years: 2010 - present
- Generation: 5
- Type of van: car
- Model variant: Base
All Torque Settings in Tables
engine torque settings
Save to email ✉️Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
---|---|---|---|---|---|---|
Oil pan | Drain plug to No.2 oil pan | 40 | 30 |
|
||
Oil pan | Oil pan to Cylinder block bolts and nut | 21 | 15 | For bolts A, B, C, E and nut |
|
|
Oil pan | Oil pan to Cylinder block bolt | 10 | 7 | For bolt D |
|
|
Oil pan | Oil pan stud bolt | 10 | 7 | For stud bolt A |
|
|
Oil pan | Oil pan stud bolts | 4 | 3 | For stud bolts B |
|
|
Oil pan | No.1 oil pan baffle plate to Oil pan | 10 | 7 |
|
||
Oil pan | No.2 oil pan to Oil pan | 10 | 7 |
|
||
Oil filter | Oil filter to Oil filter bracket | 25 | 18 |
|
||
Oil filter | Oil filter drain plug to Oil filter | 13 | 10 |
|
||
Oil filter | Oil filter bracket to Timing chain cover | 21 | 15 |
|
||
Oil filter | Oil strainer to Oil pan | 9 | 7 |
|
||
Oil pressure switch | Engine oil pressure switch to Timing chain cover | 15 | 11 |
|
||
Oil dipstick | Engine oil level dipstick guide to Timing chain cover | 10 | 7 |
|
||
Oil feeder | Oil filler cap housing to Cylinder head cover LH | 10 | 7 |
|
||
Oil pump | Oil pump relief valve plug to Oil pump cover | 49 | 36 |
|
||
Oil pump | Oil pump cover to Timing chain cover screw | 10 | 7 |
|
||
Oil pump | Oil pump cover to Timing chain cover bolt | 9 | 7 |
|
||
Piston rods | Connecting rod cap to Connecting rod | 25 | 18 | Step 1 |
|
|
Cylinder head | Cylinder head to Cylinder block | 38 | 28 | Step 1 |
|
|
Cylinder head | Cylinder head LH to Cylinder block | 36 | 27 | For cylinder head set bolt, Step 1 |
|
|
Cylinder head | Cylinder head LH to Cylinder block | 30 | 22 | Except cylinder head set bolt |
|
|
Cylinder head | Cylinder head stud bolt | 10 | 7 | For bolt A |
|
|
Cylinder head | Cylinder head stud bolt | 4 | 3 | For bolt B |
|
|
Cylinder head | No.1 straight screw plug to Cylinder head | 44 | 32 |
|
||
Cylinder head | No.2 straight screw plug to Cylinder head | 80 | 59 |
|
||
Cylinder head | Engine hanger to Cylinder head | 33 | 24 |
|
||
Cylinder head | Fuel pipe to Cylinder head cover LH | 9 | 7 |
|
||
Cylinder head | No.1 oil pipe to Cylinder head and cylinder head cover | 65 | 48 |
|
||
Cylinder head | No.2 oil pipe to Cylinder head and cylinder head cover | 65 | 48 |
|
||
Cylinder head | No.1 chain tensioner to Cylinder head RH | 10 | 7 |
|
||
Cylinder head | Cylinder head cover stud bolt | 4 | 3 |
|
||
Cylinder head | Rear cylinder head cover to Cylinder head cover and cylinder block | 9 | 7 |
|
||
Cylinder head | No.1 surge tank stay to Cylinder head sub-assembly LH | 21 | 15 |
|
||
Cylinder head | No.2 surge tank stay to Cylinder head sub-assembly LH | 21 | 15 |
|
||
Spark plugs | Spark plug to Cylinder head | 18 | 13 |
|
||
Intake manifold | Intake air surge tank to Intake manifold | 28 | 21 |
|
||
Intake manifold | Intake manifold to Cylinder head sub-assembly LH, RH | 21 | 15 |
|
||
Intake manifold | Purge VSV to Intake air surge tank | 9 | 7 |
|
||
Intake manifold | No.1 air cleaner hose clamp | 5 | 4 |
|
||
Intake manifold | No.1 air cleaner hose bolt | 5 | 4 |
|
||
Throttle body | Throttle body to Intake air surge tank | 10 | 7 |
|
||
Throttle body | Throttle body bracket to Intake air surge tank | 21 | 15 |
|
||
Engine block | Cylinder block water drain cock to Cylinder block | 30 | 22 |
|
||
Engine block | Cylinder block water drain cock plug to Cylinder block water drain cock | 13 | 10 |
|
||
Engine block | Cylinder block stud bolts | 10 | 7 | For stud bolts A |
|
|
Engine block | Cylinder block stud bolts | 4 | 3 | For stud bolts B |
|
|
Engine block | PCV valve sub-assembly to Cylinder head cover sub-assembly LH | 27 | 20 |
|
||
Engine block | Oil seal retainer to Cylinder block | 10 | 7 |
|
||
Engine block | No.1 chain vibration damper to Cylinder head LH and cylinder block | 23 | 17 |
|
||
Engine block | No.1 idler gear shaft to Cylinder block | 60 | 44 |
|
||
Engine block | No.1 oil nozzle to Cylinder block | 9 | 7 |
|
||
Engine mounts | Front No.1 engine mounting bracket RH to Cylinder block | 43 | 32 |
|
||
Engine mounts | Front No.1 engine mounting bracket LH to Cylinder block | 43 | 32 |
|
||
Engine mounts | Engine mount insulator to Engine mount bracket | 72 | 53 |
|
||
Engine mounts | Engine mount insulator to Body | 40 | 30 |
|
||
Engine mounts | Rear engine under cover to Body | 29 | 21 |
|
||
Engine mounts | No.1 engine under cover to Body | 29 | 21 |
|
||
Engine mounts | Engine under cover seal to No.1 engine under cover | 29 | 21 |
|
||
Sensor | Accelerator pedal sensor to Body | 5 | 4 |
|
||
Sensor | VVT sensor to Cylinder head | 10 | 7 |
|
||
Sensor | Crankshaft position sensor to Cylinder block | 10 | 7 |
|
||
Sensor | Engine coolant temperature sensor to Rear water by-pass joint | 20 | 15 |
|
||
Sensor | Knock sensor to Cylinder block | 20 | 15 |
|
||
Sensor | Air fuel ratio sensor to Front exhaust pipe assembly (for Bank 1) | 44 | 32 |
|
||
Sensor | Air fuel ratio sensor to Front exhaust pipe assembly (for Bank 1) | 40 | 30 | For use with SST |
|
|
Sensor | Air fuel ratio sensor to Front No.2 exhaust pipe assembly (for Bank 2) | 44 | 32 |
|
||
Sensor | Air fuel ratio sensor to Front No.2 exhaust pipe assembly (for Bank 2) | 40 | 30 | For use with SST |
|
|
Sensor | Heated oxygen sensor to Front exhaust pipe assembly (for Bank 1) | 44 | 32 |
|
||
Sensor | Heated oxygen sensor to Front exhaust pipe assembly (for Bank 1) | 40 | 30 | For use with SST |
|
|
Sensor | Heated oxygen sensor to Front No.2 exhaust pipe assembly (for Bank 2) | 44 | 32 |
|
||
Sensor | Heated oxygen sensor to Front No.2 exhaust pipe assembly (for Bank 2) | 40 | 30 | For use with SST |
|
|
Alternator | Retainer plate to Generator drive end frame | 2 | 1 |
|
||
Alternator | Generator coil assembly to Generator drive end frame | 6 | 4 |
|
||
Alternator | Generator brush holder assembly to Generator coil assembly | 2 | 1 |
|
||
Alternator | Generator rear end cover to Generator coil assembly | 5 | 4 |
|
||
Alternator | Cord clip to Generator rear end cover | 6 | 4 |
|
||
Alternator | Generator with clutch pulley to Generator rotor assembly | 80 | 59 |
|
||
Alternator | Generator with clutch pulley to Generator rotor assembly | 64 | 47 | For use with SST |
|
|
Alternator | Generator bracket to Generator assembly | 20 | 15 |
|
||
Alternator | Generator assembly to Timing chain cover | 43 | 32 |
|
||
Alternator | Generator bracket to Cylinder block | 20 | 15 |
|
||
Alternator | Wire harness to Generator assembly | 8 | 6 |
|
||
Alternator | Generator wire to Generator assembly | 10 | 7 |
|
||
Starter | Starter assembly to Transmission housing | 37 | 27 |
|
||
Starter | Starter drive housing to Magnet starter switch assembly | 6 | 4 |
|
||
Starter | Commutator end frame to Starter brush holder assembly | 2 | 1 |
|
||
Starter | Commutator end frame to Starter drive housing | 6 | 4 |
|
||
Starter | Starter wire to Starter assembly | 10 | 7 |
|
||
Starter | Starter wire to Cylinder block | 8 | 6 |
|
||
Starter | Starter cover to Starter assembly | 12 | 9 |
|
||
Starter | Lead wire to Terminal C | 6 | 4 |
|
||
Battery | Battery clamp to Body | 6 | 4 |
|
||
Battery | Ignition coil to Cylinder head cover | 10 | 7 |
|
||
Camshaft | Camshaft timing gear to Camshaft | 100 | 74 |
|
||
Camshaft | Camshaft timing exhaust gear to Camshaft | 100 | 74 |
|
||
Camshaft | No.2 chain tensioner to Camshaft housing RH | 21 | 15 |
|
||
Camshaft | No.3 chain tensioner to Camshaft housing LH | 21 | 15 |
|
||
Camshaft | Camshaft bearing cap (for Bank 1) to Cylinder head LH bolt | 28 | 21 | For bolt A |
|
|
Camshaft | Camshaft bearing cap (for Bank 1) to Cylinder head LH bolt | 16 | 12 | For bolt B |
|
|
Camshaft | Camshaft bearing cap (for Bank 2) to Cylinder head RH bolt | 28 | 21 | For bolt A |
|
|
Camshaft | Camshaft bearing cap (for Bank 2) to Cylinder head RH bolt | 16 | 12 | For bolt B |
|
|
Camshaft | Cylinder head to Camshaft housing bolts | 10 | 7 | For bolt A and D |
|
|
Camshaft | Cylinder head to Camshaft housing bolts | 21 | 15 | For bolt B and C |
|
|
Camshaft | Camshaft timing oil control valve assembly to Cylinder head | 10 | 7 |
|
||
Crankshaft | Crankshaft pulley to Crankshaft | 260 | 192 |
|
||
Crankshaft | Crankshaft bearing cap to Cylinder block | 61 | 45 | Step 1, Quantity: 16 |
|
|
Crankshaft | Crankshaft bearing cap to Cylinder block | 26 | 19 | Quantity: 8 |
|
|
Crankshaft | Drive plate and ring gear to Crankshaft | 83 | 61 |
|
||
Water pump | Water pump to Timing chain cover bolt | 47 | 35 | For bolt A |
|
|
Water pump | Water pump to Timing chain cover bolt | 11 | 8 | For bolt B |
|
|
Water pump | Water pump to Timing chain cover bolt | 23 | 17 | For bolt C |
|
|
Fuel/Oil cooler | Engine oil cooler to Oil filter bracket bolt | 68 | 50 |
|
||
Fuel/Oil cooler | Engine oil cooler to Oil filter bracket nut | 10 | 7 |
|
||
Fuel/Oil cooler | Fan shroud to Oil cooler tube | 6 | 4 |
|
||
Fuel/Oil cooler | Drain plug to No.2 oil pan | 14 | 10 |
|
||
Radiator | Radiator to Radiator support | 18 | 13 |
|
||
Radiator | Fan shroud to Radiator | 5 | 4 |
|
||
Radiator | Radiator reservoir to Fan shroud | 5 | 4 |
|
||
Radiator | Fluid coupling to Fan pulley | 21 | 15 |
|
||
Radiator | Fluid coupling to Fan | 10 | 7 |
|
||
Radiator | Water inlet housing to Timing chain cover | 10 | 7 |
|
||
Radiator | Water inlet with thermostat to Water inlet housing | 9 | 7 |
|
||
Radiator | No.1 water outlet pipe to Cylinder block | 10 | 7 |
|
||
Radiator | Water by-pass pipe to Timing chain cover and oil filter bracket | 10 | 7 |
|
||
Air conditioning | Discharge hose sub-assembly to Cooler compressor assembly | 10 | 7 |
|
||
Air conditioning | Suction hose sub-assembly to Cooler compressor assembly | 10 | 7 |
|
||
Air conditioning | Suction hose sub-assembly to Engine | 8 | 6 |
|
||
Air conditioning | Cooler compressor assembly to Engine stud bolt | 10 | 7 |
|
||
Air conditioning | Cooler compressor assembly to Engine bolt | 25 | 18 |
|
||
Air conditioning | Cooler compressor assembly to Engine nut | 25 | 18 |
|
||
Belt tensioner/Timing chains | V-ribbed belt tensioner to Timing chain cover | 36 | 27 |
|
||
Belt tensioner/Timing chains | No.1 idler pulley to Timing chain cover | 54 | 40 |
|
||
Belt tensioner/Timing chains | No.2 idler pulley to Timing chain cover | 54 | 40 |
|
||
Belt tensioner/Timing chains | Timing chain cover to Cylinder head and cylinder block | 47 | 35 | For area 1 |
|
|
Belt tensioner/Timing chains | Timing chain cover to Cylinder head and cylinder block | 23 | 17 | Except area 1 |
|
|
Belt tensioner/Timing chains | Suction hose to Timing chain cover | 8 | 6 |
|
||
Belt tensioner/Timing chains | Timing chain cover plate to Timing chain cover | 9 | 7 |
|
||
PCM | ECM to Body | 8 | 6 |
|
||
PCM | ECM bracket to ECM | 3 | 2 |
|
||
PCM | No.2 ECM bracket to ECM | 3 | 2 |
|
||
Fuel system | Fuel delivery pipe sub-assembly to Intake manifold | 21 | 15 |
|
||
Fuel system | Fuel pressure regulator to Fuel delivery pipe | 9 | 7 |
|
||
Fuel system | Fuel pump ECU to Frame | 31 | 23 |
|
||
Fuel system | Fuel tank band to body | 40 | 30 |
|
||
Fuel system | No.1 fuel tank protector sub-assembly to Body | 20 | 15 |
|
||
Fuel system | No.3 fuel tank protector to Fuel tank | 5 | 4 |
|
drivetrain torque settings
Save to email ✉️Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
---|---|---|---|---|---|---|
Transmission mount/case | Transmission under cover to Body | 29 | 21 |
|
steering torque settings
Save to email ✉️Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
---|---|---|---|---|---|---|
Power steering | Power steering oil pressure switch to Pressure feed tube | 21 | 15 |
|
||
Power steering | Pressure feed tube union bolt | 50 | 37 |
|
||
Power steering | Wire harness bracket to Vane pump assembly | 40 | 30 |
|
||
Power steering | Vane pump assembly set bolt | 43 | 32 |
|
||
Power steering | Vane pump front housing to Vane pump rear housing | 22 | 16 |
|
exhaust torque settings
Save to email ✉️Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
---|---|---|---|---|---|---|
Exhaust manifold | Exhaust manifold sub-assembly RH to Cylinder head RH | 21 | 15 |
|
||
Exhaust manifold | Exhaust manifold RH to Front exhaust pipe | 54 | 40 |
|
||
Exhaust manifold | Exhaust manifold LH to Front No.2 exhaust pipe | 54 | 40 |
|
||
Exhaust manifold | Exhaust manifold RH to No.1 exhaust manifold heat insulator | 13 | 10 |
|
||
Exhaust manifold | Exhaust manifold LH to No.2 exhaust manifold heat insulator | 13 | 10 |
|
||
Exhaust manifold | Manifold stay to Exhaust manifold LH to Front transmission case | 40 | 30 |
|
||
Exhaust manifold | No.2 manifold stay to Exhaust manifold RH to Front transmission case | 40 | 30 |
|
||
Exhaust manifold | Front exhaust pipe assembly to Center exhaust pipe assembly | 43 | 32 |
|
||
Exhaust manifold | Front exhaust pipe to Front No.2 exhaust pipe | 48 | 35 |
|
||
Exhaust manifold | Center exhaust pipe to Tailpipe assembly | 48 | 35 |
|
||
Exhaust manifold | Exhaust pipe stopper bracket to Crossmember | 19 | 14 |
|
brakes torque settings
Save to email ✉️Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to |
---|
suspension torque settings
Save to email ✉️Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to |
---|
general torque settings
Save to email ✉️Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to |
---|
Did you find the answer to your specific question?
👍 0 👎 0