Toyota Camry XV10 (1992-1996) Torque Spec Settings
By Jason Lawrence from New York - Toyota Camry, CC BY 2.0
Below you'll find the tightening torques for the Toyota Camry XV10 in both Nm and ft/lbs. The first table contains the most-used torque settings. The tables after it contain all torque spec values I could find.
Most-used torque specs for Toyota Camry XV10
| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
|---|---|---|---|---|---|---|
| Wheel hub assembly | Front axle hub nut | 294 | 217 |
|
|
|
| Transmission fluid pan | Drain plug | 49 | 36 |
|
|
|
| Steering wheel | Steering wheel | 35 | 26 |
|
|
|
| Wheels | Front wheel | 103 | 76 |
|
|
To make sure these are the correct tightening torque values, you can use the data below to verify this is the right model.
Are these torque settings right for you?
- Production years: 1992 - 1996
- Generation: 3
- Type of van: car
- Model variant: Base
All Torque Settings in Tables
engine torque settings
Save to email ✉️| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
|---|---|---|---|---|---|---|
| Engine mounts | Engine front mounting to Subframe | 80 | 59 |
|
|
|
| Engine mounts | Engine rear mounting to Subframe | 80 | 59 |
|
|
|
| Engine mounts | Engine left mounting to Subframe | 80 | 59 |
|
|
|
| Engine mounts | Engine left mounting to Transmission case | 52 | 38 |
|
|
|
| Starter | Starter to Clutch housing | 39 | 29 |
|
|
drivetrain torque settings
Save to email ✉️| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
|---|---|---|---|---|---|---|
| Differential | Ring gear to Differential case | 90 | 66 |
|
|
|
| Clutch assembly | Clutch housing stiffener plate | 37 | 27 |
|
|
|
| Clutch assembly | Clutch release cylinder to Clutch housing | 13 | 10 |
|
|
|
| Clutch assembly | Clutch release bearing retainer | 7 | 5 |
|
|
|
| Flywheel/Flex plate | Flywheel to Crankshaft | 88 | 65 |
|
|
|
| Transmission fluid pan | Filler plug | 49 | 36 |
|
|
|
| Transmission fluid pan | Drain plug | 49 | 36 |
|
|
|
| Transmission mount/case | Transaxle to Engine | 46 | 34 | 10mm bolt |
|
|
| Transmission mount/case | Transaxle to Engine | 64 | 47 | 12mm bolt |
|
|
| Transmission mount/case | Transaxle case stiffener plate | 37 | 27 |
|
|
|
| Transmission mount/case | Transmission case to Transaxle case | 29 | 21 |
|
|
|
| Transmission mount/case | Transmission case to Case cover | 29 | 21 |
|
|
|
| Transmission mount/case | Transmission case protector | 18 | 13 |
|
|
|
| Transfer | Control shift lever to Lever shaft | 6 | 4 |
|
|
|
| Transfer | Control shaft cover | 37 | 27 |
|
|
|
| Transfer | Reverse shift arm bracket | 18 | 13 |
|
|
steering torque settings
Save to email ✉️| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
|---|---|---|---|---|---|---|
| Steering rack | Steering gear housing to Subframe | 181 | 133 |
|
|
exhaust torque settings
Save to email ✉️| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
|---|---|---|---|---|---|---|
| Exhaust manifold | Exhaust front pipe to Catalytic converter | 62 | 46 |
|
|
|
| Exhaust manifold | Exhaust front pipe to Exhaust center pipe | 43 | 32 |
|
|
brakes torque settings
Save to email ✉️| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to |
|---|
suspension torque settings
Save to email ✉️| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
|---|---|---|---|---|---|---|
| Stabilizer bar | Stabilizer bar bush bracket to Subframe | 19 | 14 |
|
|
general torque settings
Save to email ✉️| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to |
|---|
M.rJirapat, CC BY-SA 4.0, via Wikimedia Commons
Did you find the answer to your specific question?
👍 2 👎 0
_in_Thailand_02.jpg){kind=link}