Toyota Camry XV20 (1996-2002) Torque Spec Settings
OSX, Public domain, via Wikimedia Commons
Below you'll find the tightening torques for the Toyota Camry XV20 in both Nm and ft/lbs. The first table contains the most-used torque settings. The tables after it contain all torque spec values I could find.
Most-used torque specs for Toyota Camry XV20
| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
|---|---|---|---|---|---|---|
| Wheels | Front wheel | 103 | 76 |
|
|
To make sure these are the correct tightening torque values, you can use the data below to verify this is the right model.
Are these torque settings right for you?
- Production years: 1996 - 2002
- Generation: 2
- Type of van: car
- Model variant: Base
- Also known as:
All Torque Settings in Tables
engine torque settings
Save to email ✉️| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
|---|---|---|---|---|---|---|
| Oil pan | No.2 oil pan to Drain plug | 45 | 33 |
|
|
|
| Oil pan | No.1 oil pan to Cylinder block | 20 | 15 |
|
|
|
| Oil pan | No.2 oil pan to No.1 oil pan | 8 | 6 |
|
|
|
| Oil pan | No.1 oil pan to Oil pump | 8 | 6 | 10mm head |
|
|
| Oil pan | No.1 oil pan to Oil pump | 20 | 15 | 12mm head |
|
|
| Oil pan | No.1 oil pan to Rear oil seal retainer | 8 | 6 |
|
|
|
| Oil pan | No.1 oil pan to Transaxle | 37 | 27 |
|
|
|
| Oil pan | Oil pan baffle plate to No.1 oil pan | 8 | 6 |
|
|
|
| Oil filter | Oil filter union to Cylinder block | 30 | 22 |
|
|
|
| Oil filter | Oil strainer to Main bearing cap | 8 | 6 |
|
|
|
| Oil pressure switch | Oil pressure switch to Cylinder block | 13 | 10 |
|
|
|
| Oil dipstick | Oil dipstick guide to LH cylinder head | 8 | 6 |
|
|
|
| Oil pump | Oil pump to Cylinder block | 8 | 6 | 10mm head |
|
|
| Oil pump | Oil pump to Cylinder block | 20 | 15 | 12mm head |
|
|
| Oil pump | Oil pump to Relief valve plug | 37 | 27 |
|
|
|
| Oil pump | Oil strainer to Oil pump | 8 | 6 |
|
|
|
| Oil pump | Timing belt plate to Oil pump | 8 | 6 |
|
|
|
| Piston rods | Connecting rod cap to Connecting rod | 25 | 18 | Step 1 |
|
|
| Cylinder head | Cylinder head to Cylinder block | 54 | 40 | 12 pointed head bolt, Step 1 |
|
|
| Cylinder head | Cylinder head to Cylinder block | 19 | 14 | Recessed head bolt |
|
|
| Cylinder head | Water inlet pipe to LH cylinder head | 20 | 15 |
|
|
|
| Cylinder head | No.1 engine hanger to RH cylinder head | 39 | 29 |
|
|
|
| Cylinder head | Cylinder head cover to Cylinder head | 8 | 6 |
|
|
|
| Cylinder head | Cylinder head rear plate to LH cylinder head | 8 | 6 |
|
|
|
| Spark plugs | Spark plug to Cylinder head | 18 | 13 |
|
|
|
| Intake manifold | Intake manifold to Cylinder head | 15 | 11 |
|
|
|
| Intake manifold | Water outlet to Intake manifold | 15 | 11 |
|
|
|
| Intake manifold | Air intake chamber to Intake manifold | 43 | 32 |
|
|
|
| Intake manifold | Intake air control valve to Air intake chamber | 15 | 11 |
|
|
|
| Intake manifold | Air intake chamber stay to Air intake chamber | 20 | 15 |
|
|
|
| Intake manifold | Air intake chamber stay to RH cylinder head | 20 | 15 |
|
|
|
| Intake manifold | No.1 engine hanger to Air intake chamber | 39 | 29 |
|
|
|
| Intake manifold | Delivery pipe to Intake manifold | 10 | 7 |
|
|
|
| Throttle body | Throttle body to Air intake chamber | 20 | 15 |
|
|
|
| Engine block | Engine coolant drain union to Cylinder block | 39 | 29 |
|
|
|
| Engine block | RH engine drain plug to EGR cooler | 7 | 5 |
|
|
|
| Engine block | LH engine drain plug to Union on cylinder block | 13 | 10 |
|
|
|
| Engine block | Water seal plate to Cylinder block | 18 | 13 |
|
|
|
| Engine block | Water inlet housing to Cylinder block | 8 | 6 |
|
|
|
| Engine block | Rear oil seal retainer to Cylinder block | 8 | 6 |
|
|
|
| Engine mounts | RH engine mounting bracket to Cylinder block | 28 | 21 |
|
|
|
| Engine mounts | No.2 generator bracket to Engine RH mounting bracket | 28 | 21 |
|
|
|
| Engine mounts | RH engine mounting stay to Water outlet | 32 | 24 |
|
|
|
| Engine mounts | RH engine mounting stay to Engine moving control rod | 32 | 24 |
|
|
|
| Engine mounts | RH engine mounting stay to No.2 RH engine mounting bracket | 32 | 24 |
|
|
|
| Engine mounts | No.2 RH engine mounting stay to No.2 generator bracket | 64 | 47 |
|
|
|
| Engine mounts | No.2 RH engine mounting stay to No.2 RH engine mounting bracket | 64 | 47 |
|
|
|
| Engine mounts | Front engine mounting insulator to Cylinder block | 64 | 47 |
|
|
|
| Engine mounts | Rear engine mounting insulator to Cylinder block | 64 | 47 |
|
|
|
| Engine mounts | Engine moving control rod to RH engine mounting bracket | 64 | 47 |
|
|
|
| Engine mounts | Engine moving control rod to RH fender apron | 64 | 47 |
|
|
|
| Engine mounts | Front engine mounting insulator to Front frame | 80 | 59 | TMC made |
|
|
| Engine mounts | Front engine mounting insulator to Front frame | 44 | 32 | TMMK made for silver color |
|
|
| Engine mounts | Front engine mounting insulator to Front frame | 66 | 49 | TMMK made for green color |
|
|
| Engine mounts | Rear engine mounting insulator to Front frame | 66 | 49 |
|
|
|
| Engine mounts | LH engine mounting insulator to Transaxle | 64 | 47 |
|
|
|
| Engine mounts | Engine mounting absorber to Front frame | 48 | 35 |
|
|
|
| Engine mounts | Engine mounting absorber to Transaxle | 48 | 35 |
|
|
|
| Sensor | Knock sensor to Cylinder block | 39 | 29 |
|
|
|
| Sensor | Heated oxygen sensor (bank 1, 2 sensor 1) to Exhaust manifold | 44 | 32 |
|
|
|
| Sensor | Heated oxygen sensor (bank 1 sensor 2) to Exhaust pipe | 44 | 32 |
|
|
|
| Sensor | EGR valve position sensor to EGR valve | 2 | 1 |
|
|
|
| Sensor | EGR gas temperature sensor to EGR valve | 20 | 15 |
|
|
|
| Sensor | A/F sensor to Exhaust manifold | 44 | 32 |
|
|
|
| Sensor | ECT sensor to Water outlet | 20 | 15 |
|
|
|
| Sensor | Camshaft position sensor to Cylinder head | 8 | 6 |
|
|
|
| Sensor | Crankshaft position sensor to Oil pump | 8 | 6 |
|
|
|
| Alternator | Generator to Generator bracket | 56 | 41 |
|
|
|
| Alternator | Generator bracket to Cylinder block | 43 | 32 |
|
|
|
| Alternator | Generator pulley to Rotor | 111 | 82 |
|
|
|
| Alternator | Generator to Adjusting bar | 18 | 13 |
|
|
|
| Starter | Starter mounting bolt | 45 | 33 |
|
|
|
| Starter | Starter housing to Magnetic switch | 6 | 4 |
|
|
|
| Starter | Lead wire to Terminal C of starter | 6 | 4 |
|
|
|
| Starter | Terminal nut to Terminal C of starter | 17 | 13 |
|
|
|
| Starter | Terminal nut to Terminal 30 of starter | 17 | 13 |
|
|
|
| Battery | No.2 oil pan to Drain plug | 45 | 33 |
|
|
|
| Camshaft | Camshaft timing pulley to Camshaft | 125 | 92 |
|
|
|
| Camshaft | Camshaft timing pulley to Camshaft | 88 | 65 | For SST |
|
|
| Camshaft | Camshaft bearing cap to Cylinder head | 16 | 12 |
|
|
|
| Crankshaft | Crankshaft pulley to Crankshaft | 215 | 159 |
|
|
|
| Crankshaft | Main bearing cap to Cylinder block | 22 | 16 | 12 pointed head bolt, Step 1 |
|
|
| Crankshaft | Main bearing cap to Cylinder block | 27 | 20 | 6 pointed head bolt |
|
|
| Water pump | Water pump to Cylinder block | 8 | 6 |
|
|
|
| Radiator | Radiator support to Body | 13 | 10 |
|
|
|
| Radiator | No.1 cooling fan shroud to Radiator | 5 | 4 |
|
|
|
| Radiator | No.2 cooling fan shroud to Radiator | 5 | 4 |
|
|
|
| Radiator | Radiator oil cooler to Radiator lower tank | 8 | 6 |
|
|
|
| Radiator | Radiator inlet pipe to Radiator lower tank | 15 | 11 |
|
|
|
| Radiator | Water inlet to Water inlet housing | 8 | 6 |
|
|
|
| Air conditioning | A/C compressor housing bracket to Cylinder block | 25 | 18 |
|
|
|
| Air conditioning | A/C compressor to Housing bracket | 25 | 18 |
|
|
|
| Air conditioning | A/C compressor to No.1 oil pan | 25 | 18 |
|
|
|
| Belt tensioner/Timing chains | Timing belt tensioner to Oil pump | 27 | 20 |
|
|
|
| Belt tensioner/Timing chains | No.1 timing belt cover to Oil pump | 9 | 7 |
|
|
|
| Belt tensioner/Timing chains | No.2 timing belt cover to No.3 timing belt cover | 9 | 7 |
|
|
|
| Belt tensioner/Timing chains | No.3 timing belt cover to Cylinder head | 9 | 7 |
|
|
|
| Belt tensioner/Timing chains | No.1 idler pulley to Oil pump | 34 | 25 |
|
|
|
| Belt tensioner/Timing chains | No.2 idler pulley to No.2 idler pulley bracket | 43 | 32 |
|
|
|
| Belt tensioner/Timing chains | No.2 idler pulley to Cylinder block | 28 | 21 |
|
|
|
| Fuel system | Fuel inlet hose to Fuel filter | 29 | 21 |
|
|
|
| Fuel system | Fuel line | 29 | 21 | Union bolt type |
|
|
| Fuel system | Fuel line | 28 | 21 | Flare nut type, Using SST |
|
|
| Fuel system | No.1 fuel pipe to Intake manifold | 20 | 15 |
|
|
|
| Fuel system | Fuel pump assembly to Fuel tank | 4 | 3 |
|
|
|
| Fuel system | Fuel filter to Fuel pump bracket | 2 | 1 |
|
|
|
| Fuel system | Fuel pressure regulator to Fuel pump bracket | 2 | 1 |
|
|
|
| Fuel system | Fuel tank band to Body | 39 | 29 |
|
|
drivetrain torque settings
Save to email ✉️| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
|---|---|---|---|---|---|---|
| Clutch assembly | Release fork support | 47 | 35 |
|
|
|
| Flywheel/Flex plate | Flywheel to Crankshaft | 83 | 61 |
|
|
|
| Flywheel/Flex plate | Flywheel housing under cover to Transaxle | 8 | 6 |
|
|
|
| Flywheel/Flex plate | Drive plate to Crankshaft | 83 | 61 |
|
|
steering torque settings
Save to email ✉️| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
|---|---|---|---|---|---|---|
| Power steering | Power steering pump to Power steering pump bracket | 43 | 32 |
|
|
|
| Power steering | Power steering pump bracket to RH cylinder head | 43 | 32 |
|
|
|
| Power steering | Power steering pump drive belt adjusting strut to Power steering pump | 43 | 32 |
|
|
|
| Power steering | Power steering pump drive belt adjusting strut to Oil pump | 43 | 32 |
|
|
|
| Power steering | Clamp plate set nut | 8 | 6 |
|
|
exhaust torque settings
Save to email ✉️| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
|---|---|---|---|---|---|---|
| Exhaust manifold | Exhaust manifold to Cylinder head | 49 | 36 |
|
|
|
| Exhaust manifold | Exhaust manifold stay to Exhaust manifold | 20 | 15 |
|
|
|
| Exhaust manifold | Exhaust manifold stay to Exhaust manifold | 20 | 15 | Except California |
|
|
| Exhaust manifold | Exhaust manifold stay to Exhaust manifold | 34 | 25 |
|
|
|
| Exhaust manifold | Exhaust manifold stay to Exhaust manifold | 34 | 25 | Except California |
|
|
| Exhaust manifold | Exhaust manifold stay to Transmission housing | 20 | 15 | Except California |
|
|
| Exhaust manifold | Exhaust manifold stay to Transmission housing | 34 | 25 |
|
|
|
| Exhaust manifold | Exhaust pipe bracket to No.1 oil pan | 21 | 15 |
|
|
|
| Exhaust manifold | Front exhaust pipe to Exhaust manifold | 62 | 46 |
|
|
|
| Exhaust manifold | Front exhaust pipe to Center exhaust pipe | 56 | 41 |
|
|
|
| Exhaust manifold | Center exhaust pipe to Tailpipe | 56 | 41 |
|
|
|
| Exhaust manifold | Front exhaust pipe bracket to Sub frame | 33 | 24 |
|
|
|
| Exhaust manifold | Front exhaust pipe support bracket to No.1 oil pan | 21 | 15 |
|
|
|
| Exhaust manifold | Front exhaust pipe support bracket to Front exhaust pipe stay | 33 | 24 |
|
|
|
| EGR | EGR valve to Air intake chamber | 12 | 9 |
|
|
|
| EGR | EGR pipe to EGR valve | 12 | 9 |
|
|
|
| EGR | EGR cooler to Cylinder block | 9 | 7 |
|
|
|
| EGR | EGR pipe to EGR cooler | 12 | 9 |
|
|
|
| EGR | No.1 EGR pipe to EGR cooler | 12 | 9 |
|
|
|
| EGR | No.1 EGR pipe to RH exhaust manifold | 12 | 9 |
|
|
|
| EGR | No.2 EGR pipe to Air intake chamber | 12 | 9 |
|
|
|
| EGR | No.2 EGR pipe to EGR cooler | 12 | 9 |
|
|
brakes torque settings
Save to email ✉️| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to |
|---|
suspension torque settings
Save to email ✉️| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to |
|---|
general torque settings
Save to email ✉️| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to |
|---|
By EurovisionNim - Own work, CC BY-SA 4.0
Did you find the answer to your specific question?
👍 1 👎 0
_CSX_sedan.jpg){kind=link}