Toyota RAV4 XA30 (2005-2012) Torque Spec Settings
By IFCAR - Own work, Public Domain
Below you'll find the tightening torques for the Toyota RAV4 XA30 in both Nm and ft/lbs. The first table contains the most-used torque settings. The tables after it contain all torque spec values I could find.
Most-used torque specs for Toyota RAV4 XA30
| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
|---|---|---|---|---|---|---|
| Wheel hub assembly | Front axle hub nut | 216 | 159 | Ø26 |
|
|
| Wheel hub assembly | Front axle hub nut | 292 | 215 | Ø30 |
|
|
| Wheels | Front wheel | 103 | 76 |
|
|
|
| Wheels | Rear wheel | 103 | 76 |
|
|
To make sure these are the correct tightening torque values, you can use the data below to verify this is the right model.
Are these torque settings right for you?
- Production years: 2005 - 2012
- Generation: 3
- Type of van: car
- Model variant: Base
- Also known as:
All Torque Settings in Tables
engine torque settings
Save to email ✉️| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
|---|---|---|---|---|---|---|
| Oil pan | Oil drain plug to Oil pan | 40 | 30 |
|
|
|
| Oil pan | Oil pan to Stiffening crankcase bolt and nut | 9 | 7 |
|
|
|
| Oil filter | Oil filter to Stiffening crankcase | 17 | 13 |
|
|
|
| Oil pressure switch | Oil pressure switch to Cylinder head | 13 | 10 |
|
|
|
| Oil dipstick | Oil dipstick guide to Cylinder block | 9 | 7 |
|
|
|
| Oil feeder | Oil filler cap to Cylinder head cover | 3 | 2 |
|
|
|
| Oil pump | Oil pump to Cylinder block | 19 | 14 |
|
|
|
| Oil pump | Oil pump drive shaft sprocket to Oil pump | 30 | 22 |
|
|
|
| Oil pump | Oil pump cover to Oil pump | 9 | 7 |
|
|
|
| Oil pump | Oil pump relief valve to Oil pump | 49 | 36 |
|
|
|
| Oil pump | Oil pump strainer to Oil pump | 9 | 7 |
|
|
|
| Piston rods | Connecting rod bolt | 25 | 18 | Step 1 |
|
|
| Cylinder head | Cylinder head set bolt | 70 | 52 | Step 1 |
|
|
| Cylinder head | Cylinder head cover to Cylinder head bolt | 11 | 8 | Bolt A |
|
|
| Cylinder head | Cylinder head cover to Cylinder head bolt | 14 | 10 | Bolt B |
|
|
| Cylinder head | Cylinder head cover to Cylinder head nut | 11 | 8 |
|
|
|
| Cylinder head | Engine wire to Cylinder head cover | 8 | 6 |
|
|
|
| Cylinder head | No.1 engine cover to Cylinder head | 7 | 5 |
|
|
|
| Cylinder head | No.1 chain vibration damper to Cylinder head and cylinder block | 9 | 7 |
|
|
|
| Cylinder head | Chain tensioner slipper to Cylinder head and cylinder block | 19 | 14 |
|
|
|
| Cylinder head | No.1 water by-pass pipe to Cylinder head | 9 | 7 |
|
|
|
| Cylinder head | No.3 water by-pass hose to Cylinder head | 9 | 7 |
|
|
|
| Spark plugs | Spark plug to Cylinder head sub-assembly | 25 | 18 |
|
|
|
| Intake manifold | Intake manifold to Cylinder head | 30 | 22 |
|
|
|
| Throttle body | Throttle body to Intake manifold | 30 | 22 |
|
|
|
| Engine block | Cylinder block stud bolts | 5 | 4 | Bolts A, C and D |
|
|
| Engine block | Cylinder block stud bolt | 22 | 16 | Bolt B |
|
|
| Engine block | No.1 oil nozzle to Cylinder block | 7 | 5 |
|
|
|
| Engine block | Idler pulley bracket to Cylinder block | 60 | 44 |
|
|
|
| Engine block | Stiffening crankcase to Cylinder block | 24 | 18 |
|
|
|
| Engine block | Oil control valve filter to Cylinder block | 30 | 22 |
|
|
|
| Engine block | Cylinder block water drain cock to Cylinder block | 25 | 18 |
|
|
|
| Engine block | Cylinder block drain cock plug to Cylinder block | 13 | 10 |
|
|
|
| Engine mounts | Engine mounting bracket RH to Timing chain cover | 55 | 41 |
|
|
|
| Engine mounts | No.1 and No.2 engine hanger to Cylinder head | 38 | 28 |
|
|
|
| Sensor | Camshaft position sensor to Cylinder head | 9 | 7 |
|
|
|
| Sensor | Crankshaft position sensor to Timing chain cover | 9 | 7 |
|
|
|
| Sensor | Engine coolant temperature sensor to Cylinder head | 20 | 15 |
|
|
|
| Sensor | Knock sensor to Cylinder block | 20 | 15 |
|
|
|
| Sensor | Air fuel ratio sensor to Exhaust manifold | 40 | 30 | For use with SST |
|
|
| Sensor | Air fuel ratio sensor to Exhaust manifold | 44 | 32 | For use without SST |
|
|
| Sensor | Heated oxygen sensor to Exhaust manifold | 40 | 30 | For use with SST |
|
|
| Sensor | Heated oxygen sensor to Exhaust manifold | 44 | 32 | For use without SST |
|
|
| Alternator | Generator assembly to Cylinder block bolt | 21 | 15 | Bolt A |
|
|
| Alternator | Generator assembly to Cylinder block bolt | 52 | 38 | Bolt B |
|
|
| Alternator | Generator wire harness bracket to Generator assembly | 8 | 6 |
|
|
|
| Alternator | Generator wire to Generator assembly | 10 | 7 |
|
|
|
| Alternator | Generator pulley with clutch to Generator rotor assembly | 110 | 81 |
|
|
|
| Alternator | Bearing retainer plate to Generator drive end frame | 2 | 1 |
|
|
|
| Alternator | Generator brush holder assembly to Generator rectifier end frame | 2 | 1 |
|
|
|
| Alternator | Generator rectifier end frame to Generator drive end frame | 6 | 4 |
|
|
|
| Alternator | Cord clip to Generator rectifier end frame | 5 | 4 |
|
|
|
| Alternator | Generator rear end cover to Generator rectifier end frame | 5 | 4 |
|
|
|
| Starter | Starter assembly to Cylinder block sub-assembly | 37 | 27 |
|
|
|
| Starter | Starter wire to Starter assembly | 10 | 7 |
|
|
|
| Starter | Starter commutator end frame assembly to Starter drive housing assembly | 6 | 4 |
|
|
|
| Starter | Magnetic switch assembly to Starter drive housing assembly | 8 | 6 |
|
|
|
| Battery | Battery carrier bracket to Body | 20 | 15 |
|
|
|
| Battery | Battery bracket reinforcement to Battery carrier | 20 | 15 |
|
|
|
| Battery | Front battery carrier to Battery bracket reinforcement | 20 | 15 |
|
|
|
| Battery | Battery clamp to Body bolt | 5 | 4 |
|
|
|
| Battery | Batter clamp to Front battery bracket nut | 5 | 4 |
|
|
|
| Battery | Battery clamp to Upper radiator support bolt | 9 | 7 |
|
|
|
| Battery | Ignition coil assembly to Cylinder head cover | 9 | 7 |
|
|
|
| Camshaft | Camshaft timing gear to Camshaft | 54 | 40 |
|
|
|
| Camshaft | No.2 camshaft timing sprocket to No.2 camshaft | 54 | 40 |
|
|
|
| Camshaft | No.1 camshaft bearing cap to Cylinder head | 30 | 22 |
|
|
|
| Camshaft | No.2 camshaft bearing cap to Cylinder head | 30 | 22 |
|
|
|
| Camshaft | No.3 camshaft bearing cap to Cylinder head | 9 | 7 |
|
|
|
| Camshaft | Camshaft timing oil control valve to Cylinder head | 9 | 7 |
|
|
|
| Crankshaft | Crankshaft pulley to Crankshaft | 180 | 133 |
|
|
|
| Crankshaft | Crankshaft bearing cap set bolt | 40 | 30 | Step 1 |
|
|
| Crankshaft | Chain tensioner plate to Crankshaft bearing cap | 12 | 9 |
|
|
|
| Crankshaft | Timing chain guide to Crankshaft bearing cap | 9 | 7 |
|
|
|
| Crankshaft | Balance shaft housing to Stiffening crankcase | 22 | 16 | Step 1 |
|
|
| Water pump | Water pump to Cylinder block | 9 | 7 |
|
|
|
| Water pump | Water pump pulley to Water pump | 26 | 19 |
|
|
|
| Fuel/Oil cooler | Oil cooler pipe to Cylinder head | 9 | 7 |
|
|
|
| Radiator | Radiator reservoir to Radiator support RH and engine mounting insulator RH | 5 | 4 |
|
|
|
| Radiator | Upper radiator support to Radiator support LH and RH | 29 | 21 |
|
|
|
| Radiator | Fan shroud with cooling fan to Radiator | 11 | 8 |
|
|
|
| Radiator | No.2 fan shroud to Radiator | 11 | 8 |
|
|
|
| Radiator | No.1 and No.2 cooling fan motor to Fan shroud | 4 | 3 |
|
|
|
| Radiator | Fan to No.1 and No.2 cooling fan motor | 6 | 4 |
|
|
|
| Radiator | Water inlet to Cylinder block | 9 | 7 |
|
|
|
| Radiator | No.1 water by-pass pipe to Upper radiator support | 9 | 7 |
|
|
|
| Belt tensioner/Timing chains | No.1 chain tensioner to Timing chain cover | 9 | 7 |
|
|
|
| Belt tensioner/Timing chains | Timing chain cover to Cylinder head and cylinder block bolt | 9 | 7 | 10mm head |
|
|
| Belt tensioner/Timing chains | Timing chain cover to Cylinder head and cylinder block bolt | 25 | 18 | 12mm head |
|
|
| Belt tensioner/Timing chains | Timing chain cover to Cylinder head and cylinder block bolt | 55 | 41 | 14mm head |
|
|
| Belt tensioner/Timing chains | Timing chain cover to Cylinder head and cylinder block nut | 11 | 8 |
|
|
|
| Belt tensioner/Timing chains | V-ribbed belt tensioner to Timing chain cover | 60 | 44 |
|
|
|
| PCM | ECM with bracket to Body | 7 | 5 |
|
|
|
| PCM | No.1 ECM bracket to ECM | 3 | 2 |
|
|
|
| PCM | No.2 ECM bracket to ECM | 3 | 2 |
|
|
|
| Fuel system | Fuel delivery pipe to Cylinder head | 20 | 15 |
|
|
|
| Fuel system | Fuel tank vent tube set plate to Fuel tank | 4 | 3 |
|
|
|
| Fuel system | Fuel tank filler pipe to Body | 24 | 18 |
|
|
|
| Fuel system | Fuel tank band to Body | 40 | 30 |
|
|
|
| Fuel system | Fuel sender gauge assembly to Fuel tank | 2 | 1 |
|
|
|
| Fuel system | Fuel pressure pulsation damper to Fuel delivery pipe | 9 | 7 |
|
|
drivetrain torque settings
Save to email ✉️| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
|---|---|---|---|---|---|---|
| Flywheel/Flex plate | Drive plate to Crankshaft | 98 | 72 |
|
|
|
| Drive/Axle shaft | Drive shaft bearing bracket to Cylinder block | 64 | 47 |
|
|
steering torque settings
Save to email ✉️| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to |
|---|
exhaust torque settings
Save to email ✉️| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
|---|---|---|---|---|---|---|
| Exhaust manifold | Exhaust manifold to Cylinder head | 37 | 27 |
|
|
|
| Exhaust manifold | No.1 exhaust manifold heat insulator to Exhaust manifold | 12 | 9 |
|
|
|
| Exhaust manifold | No.1 and No.2 manifold stay to Cylinder block and exhaust manifold | 44 | 32 |
|
|
|
| Exhaust manifold | Front exhaust pipe assembly to Exhaust manifold | 43 | 32 |
|
|
|
| Exhaust manifold | Center exhaust pipe assembly to Front exhaust pipe assembly | 43 | 32 |
|
|
|
| Exhaust manifold | Tailpipe assembly to Center exhaust pipe assembly | 43 | 32 |
|
|
brakes torque settings
Save to email ✉️| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
|---|---|---|---|---|---|---|
| Brake pedal | Accelerator pedal to Body | 5 | 4 |
|
|
suspension torque settings
Save to email ✉️| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to |
|---|
general torque settings
Save to email ✉️| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to |
|---|
By Elise240SX - Own work, CC BY-SA 4.0
Did you find the answer to your specific question?
👍 1 👎 6
