Toyota RAV4 XA30 (2005-2012) Torque Spec Settings
By IFCAR - Own work, Public Domain
Below you'll find the tightening torques for the Toyota RAV4 XA30 in both Nm and ft/lbs. The first table contains the most-used torque settings. The tables after it contain all torque spec values I could find.
Most-used torque specs for Toyota RAV4 XA30
| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
|---|---|---|---|---|---|---|
| Wheel hub assembly | Front axle hub nut | 216 | 159 | Ø26 |
|
|
| Wheel hub assembly | Front axle hub nut | 292 | 215 | Ø30 |
|
|
| Wheels | Front wheel | 103 | 76 |
|
|
|
| Wheels | Rear wheel | 103 | 76 |
|
|
To make sure these are the correct tightening torque values, you can use the data below to verify this is the right model.
Are these torque settings right for you?
- Production years: 2005 - 2012
- Generation: 3
- Type of van: car
- Model variant: Base
- Also known as:
All Torque Settings in Tables
engine torque settings
Save to email ✉️| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
|---|---|---|---|---|---|---|
| Oil pan | Oil pan drain plug to No.2 oil pan | 40 | 30 |
|
|
|
| Oil pan | Oil pan to Cylinder block | 10 | 7 | Bolt A |
|
|
| Oil pan | Oil pan to Cylinder block | 21 | 15 | Except bolt A and nut |
|
|
| Oil pan | No.2 oil pan to Oil pan | 10 | 7 |
|
|
|
| Oil pan | Oil pan baffle plate to Cylinder block | 10 | 7 |
|
|
|
| Oil filter | Oil filter cap to Oil pan | 25 | 18 |
|
|
|
| Oil filter | Oil filter drain plug to Oil filter cap | 13 | 10 |
|
|
|
| Oil filter | Oil strainer to Cylinder block | 10 | 7 |
|
|
|
| Oil pressure switch | Oil pressure switch to Oil pan | 15 | 11 |
|
|
|
| Oil dipstick | No.1 oil dipstick guide to Cylinder block | 21 | 15 |
|
|
|
| Oil dipstick | No.2 oil dipstick guide to Cylinder block | 21 | 15 |
|
|
|
| Oil pump | Oil pump cover to Timing chain cover | 9 | 7 |
|
|
|
| Oil pump | Plug to Oil pump cover | 49 | 36 |
|
|
|
| Piston rods | Connecting rod to Connecting cap | 25 | 18 | Step 1 |
|
|
| Cylinder head | Cylinder head stud bolts | 10 | 7 | Stud bolts A and B |
|
|
| Cylinder head | Cylinder head stud bolt | 4 | 3 | Stud bolt C |
|
|
| Cylinder head | Cylinder head (for bank 1) to Cylinder block | 36 | 27 | Step 1 |
|
|
| Cylinder head | Cylinder head (for bank 2) to Cylinder block | 36 | 27 | Step 1 |
|
|
| Cylinder head | Cylinder head (for bank 2) to Cylinder block | 30 | 22 | Except bolt |
|
|
| Cylinder head | Cylinder head cover to Cylinder head | 21 | 15 | Bolt A |
|
|
| Cylinder head | Cylinder head cover to Cylinder head | 10 | 7 | Except bolt A |
|
|
| Cylinder head | No.1 chain vibration damper to Cylinder block | 23 | 17 |
|
|
|
| Cylinder head | Oil pipe bracket to Cylinder head (for bank 1) | 10 | 7 |
|
|
|
| Cylinder head | Oil pipe union bolt to Cylinder head (for bank 1) | 65 | 48 |
|
|
|
| Cylinder head | Oil pipe union bolt to Cylinder head cover (for bank 1) | 65 | 48 |
|
|
|
| Cylinder head | No.1 oil pipe union bolt to Cylinder head (for bank 2) | 65 | 48 |
|
|
|
| Cylinder head | No.1 oil pipe union bolt to Cylinder head cover (for bank 2) | 65 | 48 |
|
|
|
| Spark plugs | Spark plug to Cylinder head sub-assembly | 25 | 18 |
|
|
|
| Intake manifold | Intake manifold to Cylinder head | 21 | 15 |
|
|
|
| Intake manifold | Intake air surge tank to Intake manifold | 18 | 13 | 5mm hexagon wrench |
|
|
| Intake manifold | Intake air surge tank to Intake manifold | 21 | 15 | For bolt |
|
|
| Intake manifold | Intake air surge tank to Intake manifold | 16 | 12 | For nut |
|
|
| Throttle body | Throttle body to Intake air surge tank assembly | 10 | 7 |
|
|
|
| Engine block | Cylinder block stud bolt | 10 | 7 |
|
|
|
| Engine block | No.1 chain tensioner to Cylinder block | 10 | 7 |
|
|
|
| Engine block | Idle sprocket to Cylinder block | 60 | 44 |
|
|
|
| Engine block | Cylinder block water drain cock to Cylinder block | 25 | 18 | Step 1 |
|
|
| Engine block | Cylinder block drain cock plug to Cylinder block | 13 | 10 |
|
|
|
| Engine block | Engine rear oil seal retainer to Cylinder block | 10 | 7 |
|
|
|
| Engine mounts | Front No.1 engine mounting bracket to Timing chain cover | 54 | 40 |
|
|
|
| Engine mounts | Engine mounting bracket LH to Engine mounting insulator LH | 56 | 41 |
|
|
|
| Engine mounts | Engine mounting bracket FR to Engine mounting insulator FR | 145 | 107 |
|
|
|
| Engine mounts | Engine mounting bracket RR to Engine mounting insulator RR | 95 | 70 |
|
|
|
| Engine mounts | No.2 engine mounting stay RH to Intake manifold | 21 | 15 |
|
|
|
| Engine mounts | No.2 engine mounting stay RH to Timing chain cover | 21 | 15 |
|
|
|
| Sensor | Crankshaft position sensor to Cylinder block | 10 | 7 |
|
|
|
| Sensor | Engine coolant temperature sensor to Water outlet | 20 | 15 |
|
|
|
| Sensor | Knock sensor to Cylinder block sub-assembly | 20 | 15 |
|
|
|
| Sensor | Air fuel ratio sensor to Exhaust manifold sub-assembly | 44 | 32 |
|
|
|
| Sensor | Air fuel ratio sensor to Exhaust manifold sub-assembly | 40 | 30 | With SST |
|
|
| Sensor | Oxygen sensor to Front pipe assembly | 44 | 32 |
|
|
|
| Sensor | Oxygen sensor to Front pipe assembly | 40 | 30 | With SST |
|
|
| Sensor | VVT sensor to Cylinder head cover | 10 | 7 |
|
|
|
| Alternator | Generator assembly to Cylinder block | 43 | 32 |
|
|
|
| Alternator | Wire harness clamp stay to Generator assembly | 8 | 6 |
|
|
|
| Alternator | Generator wire to Generator assembly | 10 | 7 |
|
|
|
| Alternator | Generator pulley with clutch to Generator rotor assembly | 110 | 81 |
|
|
|
| Alternator | Bearing retainer plate to Generator drive end frame | 2 | 1 |
|
|
|
| Alternator | Generator brush holder assembly to Generator rectifier end frame | 2 | 1 |
|
|
|
| Alternator | Generator rectifier end frame to Generator drive end frame | 6 | 4 |
|
|
|
| Alternator | Generator rear end cover to Generator rectifier end frame | 5 | 4 |
|
|
|
| Starter | Starter assembly to Cylinder block sub-assembly | 37 | 27 |
|
|
|
| Starter | Starter wire to Starter assembly | 10 | 7 |
|
|
|
| Starter | Starter commutator end frame to Starter drive housing assembly | 6 | 4 |
|
|
|
| Starter | Starter magnetic switch assembly to Starter drive housing assembly | 8 | 6 |
|
|
|
| Battery | Battery bracket reinforcement to Body | 19 | 14 |
|
|
|
| Battery | Front battery bracket to Battery bracket reinforcement | 19 | 14 |
|
|
|
| Battery | Front battery bracket to Body | 19 | 14 |
|
|
|
| Battery | Battery clamp to Body | 5 | 4 |
|
|
|
| Battery | Ignition coil assembly to Cylinder head cover | 10 | 7 |
|
|
|
| Camshaft | Camshaft timing gear to Intake camshaft | 100 | 74 |
|
|
|
| Camshaft | Camshaft timing exhaust gear to Exhaust camshaft | 100 | 74 |
|
|
|
| Camshaft | Camshaft bearing cap to Camshaft housing (for bank 1) | 10 | 7 | Step 1 |
|
|
| Camshaft | Camshaft bearing cap to Camshaft housing (for bank 1) | 16 | 12 | Step 2 |
|
|
| Camshaft | Camshaft bearing cap to Camshaft housing (for bank 2) | 10 | 7 | Step 1 |
|
|
| Camshaft | Camshaft bearing cap to Camshaft housing (for bank 2) | 16 | 12 | Step 2 |
|
|
| Camshaft | Camshaft housing to Cylinder head (for bank 1) | 28 | 21 |
|
|
|
| Camshaft | Camshaft housing to Cylinder head (for bank 2) | 28 | 21 |
|
|
|
| Camshaft | No.2 chain tensioner to Camshaft housing (for bank 1) | 21 | 15 |
|
|
|
| Camshaft | No.3 chain tensioner to Camshaft housing (for bank 2) | 21 | 15 |
|
|
|
| Camshaft | Camshaft timing oil control valve to Cylinder head cover | 10 | 7 |
|
|
|
| Crankshaft | Crankshaft pulley to Crankshaft | 250 | 184 |
|
|
|
| Crankshaft | Cylinder block to Crankshaft bearing cap | 61 | 45 | Step 1 |
|
|
| Crankshaft | Main bearing cap bolt | 52 | 38 |
|
|
|
| Water pump | Water pump to Cylinder block | 21 | 15 | Bolt A |
|
|
| Water pump | Water pump to Cylinder block | 9 | 7 | Bolt B |
|
|
| Water pump | Water pump to Cylinder block | 9 | 7 | Bolt C |
|
|
| Water pump | Water pump pulley to Water pump | 21 | 15 |
|
|
|
| Radiator | Radiator reservoir tank to Body | 5 | 4 |
|
|
|
| Radiator | Upper radiator support to Radiator support LH and RH | 29 | 21 |
|
|
|
| Radiator | Fan shroud with cooling fan to Radiator | 11 | 8 |
|
|
|
| Radiator | No.2 fan shroud to Radiator | 11 | 8 |
|
|
|
| Radiator | No.1 and No.2 cooling fan motor to Fan shroud | 4 | 3 |
|
|
|
| Radiator | Fan to No.1 and No.2 cooling fan motor | 6 | 4 |
|
|
|
| Radiator | Water inlet pipe to Cylinder block | 10 | 7 |
|
|
|
| Radiator | Water inlet to Water inlet housing | 10 | 7 |
|
|
|
| Radiator | Water outlet to Cylinder head | 10 | 7 |
|
|
|
| Radiator | No.1 water by-pass pipe to Upper radiator support | 9 | 7 |
|
|
|
| Belt tensioner/Timing chains | No.2 idler pulley to Timing chain cover | 43 | 32 |
|
|
|
| Belt tensioner/Timing chains | No.2 timing gear cover to Timing chain cover | 6 | 4 |
|
|
|
| Belt tensioner/Timing chains | V-ribbed belt tensioner to Timing chain cover | 43 | 32 |
|
|
|
| Belt tensioner/Timing chains | V-ribbed belt tensioner to Cylinder block | 43 | 32 |
|
|
|
| PCM | ECM to Body | 7 | 5 |
|
|
|
| Fuel system | Fuel delivery pipe sub-assembly to Intake manifold | 21 | 15 |
|
|
|
| Fuel system | Fuel tank bent tube set plate to Fuel tank assembly | 4 | 3 |
|
|
|
| Fuel system | Fuel filler pipe to Body | 24 | 18 |
|
|
|
| Fuel system | Fuel tank band to Body | 40 | 30 |
|
|
|
| Fuel system | Fuel sender gauge assembly to Fuel tank | 2 | 1 |
|
|
|
| Fuel system | Fuel pump resistor to Body | 7 | 5 |
|
|
drivetrain torque settings
Save to email ✉️| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
|---|---|---|---|---|---|---|
| Flywheel/Flex plate | Drive plate and ring gear to Crankshaft | 178 | 131 |
|
|
|
| Drive/Axle shaft | Drive shaft bearing bracket to Cylinder block | 64 | 47 |
|
|
steering torque settings
Save to email ✉️| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to |
|---|
exhaust torque settings
Save to email ✉️| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
|---|---|---|---|---|---|---|
| Exhaust manifold | Exhaust manifold LH to Cylinder head | 21 | 15 |
|
|
|
| Exhaust manifold | Exhaust manifold RH to Cylinder head | 21 | 15 |
|
|
|
| Exhaust manifold | No.2 exhaust heat insulator to Exhaust manifold | 9 | 7 |
|
|
|
| Exhaust manifold | No.2 manifold stay to Exhaust manifold | 34 | 25 |
|
|
|
| Exhaust manifold | No.2 manifold stay to Cylinder block | 34 | 25 |
|
|
|
| Exhaust manifold | Exhaust manifold LH to Front exhaust pipe assembly | 62 | 46 |
|
|
|
| Exhaust manifold | No.1 front exhaust pipe support bracket to No.1 exhaust pipe support bracket stay | 21 | 15 |
|
|
|
| Exhaust manifold | Front exhaust pipe assembly to Center exhaust pipe assembly | 43 | 32 |
|
|
|
| Exhaust manifold | Exhaust manifold RH to Center exhaust pipe assembly | 62 | 46 |
|
|
|
| Exhaust manifold | Center exhaust pipe assembly to Tailpipe assembly | 43 | 32 |
|
|
brakes torque settings
Save to email ✉️| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
|---|---|---|---|---|---|---|
| Brake pedal | Accelerator pedal rod to Body | 5 | 4 |
|
|
|
| Parking brake | Parking brake cable assembly No.2 to Body bolt | 6 | 4 |
|
|
|
| Parking brake | Parking brake cable assembly No.2 to Body nut | 9 | 7 |
|
|
suspension torque settings
Save to email ✉️| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to |
|---|
general torque settings
Save to email ✉️| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to |
|---|
By Elise240SX - Own work, CC BY-SA 4.0
Did you find the answer to your specific question?
👍 1 👎 6
