Toyota Yaris XP90 (2005-2012) Torque Spec Settings
By M 93 - Own work, CC BY-SA 3.0 de
Below you'll find the tightening torques for the Toyota Yaris XP90 in both Nm and ft/lbs. The first table contains the most-used torque settings. The tables after it contain all torque spec values I could find.
Most-used torque specs for Toyota Yaris XP90
| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
|---|---|---|---|---|---|---|
| Oil pan | Oil pan drain plug | 38 | 28 |
|
|
|
| Wheels | Front wheel | 103 | 76 |
|
|
|
| Wheels | Rear wheel | 103 | 76 |
|
|
To make sure these are the correct tightening torque values, you can use the data below to verify this is the right model.
Are these torque settings right for you?
- Production years: 2005 - 2012
- Generation: 2
- Type of van: car
- Model variant: Base
- Also known as:
All Torque Settings in Tables
engine torque settings
Save to email ✉️| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
|---|---|---|---|---|---|---|
| Oil pan | Oil pan drain plug | 38 | 28 |
|
|
|
| Oil pan | Oil pan sub-assembly stud bolt | 5 | 4 |
|
|
|
| Oil pan | Cylinder block assembly to Oil pan sub-assembly | 24 | 18 |
|
|
|
| Oil pan | Oil pan sub-assembly to Oil pan sub-assembly No.2 | 9 | 7 |
|
|
|
| Oil filter | Oil filter sub-assembly | 13 | 10 |
|
|
|
| Oil filter | Oil pan sub-assembly to Oil filter union | 30 | 22 |
|
|
|
| Oil filter | Oil pan sub-assembly to Oil strainer | 11 | 8 |
|
|
|
| Oil pressure switch | Oil pressure switch to Cylinder block assembly | 15 | 11 |
|
|
|
| Oil pump | Oil pump assembly to Cylinder head and block | 32 | 24 | Bolt A |
|
|
| Oil pump | Oil pump assembly to Cylinder head and block | 11 | 8 | Bolt B |
|
|
| Oil pump | Oil pump assembly to Cylinder head and block | 11 | 8 | Bolt C |
|
|
| Oil pump | Oil pump assembly to Cylinder head and block | 24 | 18 | Nut D |
|
|
| Oil pump | Oil pump assembly to Cylinder head and block | 24 | 18 | Bolt E |
|
|
| Oil pump | Fan belt adjusting bar to Oil pump assembly | 11 | 8 |
|
|
|
| Oil pump | Screw plug to Oil pump assembly | 5 | 4 |
|
|
|
| Oil pump | Oil pump cover to Oil pump assembly bolt | 9 | 7 |
|
|
|
| Oil pump | Oil pump cover to Oil pump assembly screw | 10 | 7 |
|
|
|
| Oil pump | Oil pump cover to Oil pump relief valve plug | 25 | 18 |
|
|
|
| Piston rods | Connecting rod assembly to Connecting rod cap | 15 | 11 |
|
|
|
| Cylinder head | Cylinder head assembly to Cylinder block assembly | 29 | 21 | Step 1 |
|
|
| Cylinder head | Cylinder head assembly stud bolt | 10 | 7 | Bolt A |
|
|
| Cylinder head | Cylinder head assembly stud bolt | 10 | 7 | Bolt B |
|
|
| Cylinder head | Cylinder head assembly stud bolt | 10 | 7 | Bolt C |
|
|
| Cylinder head | Cylinder head assembly stud bolt | 9 | 7 | Bolt D |
|
|
| Cylinder head | Cylinder head assembly to Harness bracket | 13 | 10 |
|
|
|
| Cylinder head | Cylinder head cover sub-assembly to Cylinder head assembly | 10 | 7 |
|
|
|
| Cylinder head | Cylinder head cover No.2 to Cylinder head cover | 7 | 5 |
|
|
|
| Cylinder head | Ventilation valve sub-assembly to Cylinder head cover sub-assembly | 27 | 20 |
|
|
|
| Spark plugs | Spark plugs to Cylinder head assembly | 18 | 13 |
|
|
|
| Intake manifold | Intake manifold to Cylinder block assembly | 30 | 22 |
|
|
|
| Throttle body | Throttle with motor body assembly to Intake manifold | 9 | 7 |
|
|
|
| Throttle body | Water filler sub-assembly to Throttle with motor body assembly | 8 | 6 |
|
|
|
| Throttle body | Throttle with motor body assembly to Wire harness with bracket | 9 | 7 |
|
|
|
| Engine block | Cylinder block assembly stud bolt | 5 | 4 | Bolt A |
|
|
| Engine block | Cylinder block assembly stud bolt | 5 | 4 | Bolt B |
|
|
| Engine block | Cylinder block assembly stud bolt | 11 | 8 | Bolt C |
|
|
| Engine block | Cylinder block assembly stud bolt | 5 | 4 | Bolt D |
|
|
| Engine block | Water inlet to Cylinder block assembly | 9 | 7 |
|
|
|
| Engine mounts | Transverse engine mounting bracket to Cylinder head and block | 55 | 41 |
|
|
|
| Engine mounts | Engine mounting insulator RH to Body | 45 | 33 | Bolt A |
|
|
| Engine mounts | Engine mounting insulator RH to Body | 52 | 38 | Bolt B |
|
|
| Engine mounts | Engine mounting insulator RH to Body | 52 | 38 |
|
|
|
| Engine mounts | Engine mounting insulator LH to Engine mounting bracket LH | 52 | 38 |
|
|
|
| Engine mounts | Front suspension crossmember sub-assembly to Engine moving control rod | 120 | 89 |
|
|
|
| Sensor | Air fuel ratio sensor to Exhaust manifold assembly | 44 | 32 |
|
|
|
| Sensor | Heated oxygen sensor to Front exhaust pipe | 44 | 32 |
|
|
|
| Sensor | Heated oxygen sensor (for sensor 2) to Exhaust front pipe assembly | 44 | 32 |
|
|
|
| Sensor | Camshaft position sensor to Cylinder head assembly | 8 | 6 |
|
|
|
| Sensor | Crankshaft position sensor to Oil pump assembly | 8 | 6 |
|
|
|
| Sensor | Engine coolant temperature sensor to Cylinder head assembly | 20 | 15 |
|
|
|
| Sensor | Knock sensor to Cylinder block assembly | 20 | 15 |
|
|
|
| Alternator | Generator assembly to Wire harness clamp | 10 | 7 |
|
|
|
| Alternator | Generator assembly to Cylinder block sub-assembly | 54 | 40 |
|
|
|
| Alternator | Generator assembly to Fan belt adjusting slide | 19 | 14 |
|
|
|
| Alternator | Generator pulley to Generator rotor assembly | 133 | 98 |
|
|
|
| Alternator | Generator brush holder assembly to Generator holder with rectifier | 2 | 1 |
|
|
|
| Alternator | Rear end cover to Generator rectifier end frame | 4 | 3 |
|
|
|
| Alternator | Terminal insulator to enerator regulator assembly | 4 | 3 |
|
|
|
| Alternator | Generator regulator assembly to Generator rectifier end frame | 2 | 1 |
|
|
|
| Alternator | Generator holder with rectifier to Generator rectifier end frame | 2 | 1 |
|
|
|
| Alternator | Generator holder with rectifier to Generator rectifier end frame | 5 | 4 |
|
|
|
| Starter | Starter assembly to Transaxle housing | 37 | 27 | For 0.8kW type |
|
|
| Starter | Starter assembly to Transaxle housing | 37 | 27 | For 1.6kW type |
|
|
| Starter | Starter assembly to Terminal 30 | 10 | 7 | For 0.8kW type |
|
|
| Starter | Starter assembly to Terminal 30 | 10 | 7 | For 1.6kW type |
|
|
| Starter | Starter brush holder assembly to Commutator end frame | 2 | 1 | For 0.8kW type |
|
|
| Starter | Starter yoke assembly to Commutator end frame | 6 | 4 | For 0.8kW type |
|
|
| Starter | Starter yoke assembly to Starter commutator end frame assembly | 6 | 4 | For 1.6kW type |
|
|
| Starter | Magnet starter switch assembly to Starter housing | 8 | 6 | For 0.8kW type |
|
|
| Starter | Magnet switch body to Starter drive housing assembly | 8 | 6 | For 1.6kW type |
|
|
| Battery | Battery to Battery clamp | 4 | 3 |
|
|
|
| Battery | Battery carrier to Body | 17 | 13 |
|
|
|
| Battery | Battery terminal to Cable | 5 | 4 |
|
|
|
| Battery | Battery negative terminal to Battery negative cable | 5 | 4 |
|
|
|
| Battery | Ignition coil to Cylinder head cover | 9 | 7 |
|
|
|
| Camshaft | Camshaft bearing cap No.1 to Cylinder head assembly | 23 | 17 |
|
|
|
| Camshaft | Camshaft bearing cap No.2 to Cylinder head assembly | 13 | 10 |
|
|
|
| Camshaft | Camshaft No.2 to Camshaft timing sprocket | 64 | 47 |
|
|
|
| Camshaft | Camshaft timing gear assembly to Camshaft | 64 | 47 |
|
|
|
| Camshaft | Camshaft timing oil control valve assembly to Cylinder head assembly | 8 | 6 |
|
|
|
| Crankshaft | Cylinder block assembly to Crankshaft bearing cap | 22 | 16 |
|
|
|
| Crankshaft | Crankshaft damper sub-assembly to Crankshaft | 128 | 94 |
|
|
|
| Crankshaft | Chain vibration damper No.1 to Cylinder head and block | 9 | 7 |
|
|
|
| Water pump | Water pump assembly to Oil pump assembly | 11 | 8 |
|
|
|
| Water pump | Water pump pulley to Water pump assembly | 15 | 11 |
|
|
|
| Radiator | Radiator support sub-assembly upper to Body | 6 | 4 |
|
|
|
| Radiator | Water filler sub-assembly to Radiator sub-assembly | 8 | 6 |
|
|
|
| Radiator | Water inlet to Radiator hose | 9 | 7 |
|
|
|
| Radiator | Cooling fan resistor to Body | 5 | 4 |
|
|
|
| Belt tensioner/Timing chains | Chain tensioner slipper to Cylinder block assembly | 9 | 7 |
|
|
|
| Belt tensioner/Timing chains | Cylinder block assembly to Chain tensioner assembly No.1 | 9 | 7 |
|
|
|
| PCM | ECM to Body | 8 | 6 |
|
|
|
| Fuel system | Fuel delivery pipe subassembly to Cylinder head assembly bolt | 19 | 14 | Bolt A |
|
|
| Fuel system | Fuel delivery pipe subassembly to Cylinder head assembly bolt | 9 | 7 | Bolt B |
|
|
| Fuel system | Fuel tank assembly to Floor panel | 14 | 10 |
|
|
|
| Fuel system | Fuel tank cover vent case sub-assembly to Floor panel | 5 | 4 |
|
|
drivetrain torque settings
Save to email ✉️| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
|---|---|---|---|---|---|---|
| Wheel hub assembly | Front wheel hub nut | 103 | 76 |
|
|
|
| Flywheel/Flex plate | Flywheel sub-assembly to Crankshaft | 49 | 36 | Step 1 |
|
|
| Flywheel/Flex plate | Drive plate and torque converter clutch setting bolt to Drive plate and ring gear sub-assembly | 27 | 20 |
|
|
|
| Flywheel/Flex plate | Drive plate and ring gear sub-assembly to Crankshaft | 88 | 65 |
|
|
|
| Transmission mount/case | Automatic transaxle assembly to Engine block sub-assembly | 30 | 22 |
|
|
|
| Drive/Axle shaft | Drive shaft heat insulator sub-assembly to Cylinder block sub-assembly | 18 | 13 |
|
|
steering torque settings
Save to email ✉️| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to |
|---|
exhaust torque settings
Save to email ✉️| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
|---|---|---|---|---|---|---|
| Exhaust manifold | Exhaust manifold to Cylinder head assembly | 27 | 20 |
|
|
|
| Exhaust manifold | Exhaust manifold heat insulator No.1 to Exhaust manifold | 8 | 6 |
|
|
|
| Exhaust manifold | Manifold support bracket to Cylinder block and exhaust manifold | 44 | 32 |
|
|
|
| Exhaust manifold | Exhaust front pipe assembly to Exhaust manifold | 43 | 32 |
|
|
brakes torque settings
Save to email ✉️| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
|---|---|---|---|---|---|---|
| Brake pedal | Accelerator pedal assembly to Body | 5 | 4 |
|
|
suspension torque settings
Save to email ✉️| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to |
|---|
general torque settings
Save to email ✉️| Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to |
|---|
By M 93 - Own work, CC BY-SA 3.0 de
Did you find the answer to your specific question?
👍 5 👎 5
