Toyota Corolla E140 (2007-2013) Torque Spec Settings
Below you'll find the tightening torques for the Toyota Corolla E140 in both Nm and ft/lbs. The first table contains the most-used torque settings. The tables after it contain all torque spec values I could find.
Most-used torque specs for Toyota Corolla E140
Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
---|---|---|---|---|---|---|
Spark plugs | Spark plugs | 19 | 14 |
|
To make sure these are the correct tightening torque values, you can use the data below to verify this is the right model.
Are these torque settings right for you?
- Production years: 2007 - 2013
- Generation: 10
- Type of van: car
- Model variant: Base
All Torque Settings in Tables
engine torque settings
Save to email ✉️Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
---|---|---|---|---|---|---|
Oil pan | Oil pan drain plug to Oil pan subassembly | 25 | 18 |
|
||
Oil filter | Oil filter to Stiffening crankcase | 18 | 13 |
|
||
Oil filter | Oil filter union to Stiffening crankcase assembly | 30 | 22 |
|
||
Oil pressure switch | Oil pressure switch to Cylinder block | 15 | 11 |
|
||
Oil dipstick | Engine oil level dipstick guide to Cylinder block | 9 | 7 |
|
||
Oil pump | Oil pump drive shaft gear nut | 30 | 22 |
|
||
Oil pump | Oil pump cover to Oil pump | 9 | 7 |
|
||
Oil pump | Oil pump relief valve plug to Oil pump | 49 | 36 |
|
||
Oil pump | Oil pump strainer to Oil pump | 9 | 7 |
|
||
Oil pump | Oil pump to Cylinder block | 19 | 14 |
|
||
Cylinder head | Straight head screw plugs | 86 | 63 |
|
||
Cylinder head | Cylinder head set bolts and plate washers | 70 | 52 |
|
||
Cylinder head | Ground cable to Cylinder head mounting bolts | 8 | 6 |
|
||
Spark plugs | Spark plugs | 19 | 14 |
|
||
Intake manifold | Intake manifold mounting bolt and nut | 30 | 22 |
|
||
Engine mounts | Engine mounting insulator sub-assembly RH mounting bolt and nut | 52 | 38 | Bolt A and Nut B |
|
|
Starter | Starter assembly to Transaxle housing | 37 | 27 |
|
||
Starter | Commutator end frame to Starter brush holder assembly | 2 | 1 |
|
||
Starter | Commutator end frame to Starter housing | 6 | 4 |
|
||
Starter | Magnet starter switch assembly to Starter housing | 8 | 6 |
|
||
Battery | Battery carrier to Frame | 13 | 10 |
|
||
Battery | Battery clamp bolt | 4 | 3 |
|
||
Battery | Battery clamp to Body | 7 | 5 |
|
||
Battery | Ignition coils | 9 | 7 |
|
||
Camshaft | Camshaft timing oil control valve mounting bolt | 9 | 7 |
|
||
Camshaft | Camshaft bearing cap | 30 | 22 | (No.1/No.2) |
|
|
Camshaft | Camshaft bearing cap | 9 | 7 | (No.3) |
|
|
Crankshaft | Crankshaft pulley | 180 | 133 | (final) |
|
|
Crankshaft | Balance shaft housing to Stiffening crankcase assembly | 22 | 16 | Stage 1 |
|
|
Crankshaft | Stiffening crankcase assembly to Cylinder block | 24 | 18 |
|
||
Fuel/Oil cooler | Oil cooler hose to Fan shroud | 6 | 4 |
|
||
Coolant expansion tank | Radiator reserve tank assembly to Body | 7 | 5 |
|
||
Air conditioning | Compressor assembly with pulley to Engine | 25 | 18 |
|
||
Air conditioning | Compressor assembly with pulley to Engine stud bolt | 10 | 7 |
|
||
Air conditioning | Discharge hose subassembly to Compressor assembly with pulley | 10 | 7 |
|
||
Air conditioning | Suction hose subassembly to Compressor assembly with pulley | 10 | 7 |
|
||
Belt tensioner/Timing chains | Chain tensioner plate mounting bolt | 12 | 9 |
|
||
Belt tensioner/Timing chains | No. 1 chain vibration damper mounting bolt | 9 | 7 |
|
||
Belt tensioner/Timing chains | Chain tensioner slipper mounting bolt | 19 | 14 |
|
||
Belt tensioner/Timing chains | Timing chain guide mounting bolt | 9 | 7 |
|
||
Belt tensioner/Timing chains | Chain tensioner mounting nut | 9 | 7 |
|
||
Belt tensioner/Timing chains | V-ribbed belt tensioner bolt and nut | 60 | 44 |
|
||
Fuel system | Fuel delivery pipe sub-assembly mounting bolt | 20 | 15 |
|
||
Fuel system | Fuel pressure pulsation damper mounting bolt | 9 | 7 |
|
||
Fuel system | Fuel tank band to Body | 39 | 29 |
|
||
Fuel system | No.1 fuel tank protector subassembly to Fuel tank | 6 | 4 |
|
||
Fuel system | No.1 fuel tank protector to Body | 6 | 4 |
|
drivetrain torque settings
Save to email ✉️Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
---|---|---|---|---|---|---|
Flywheel/Flex plate | Drive plate and ring gear subassembly to Crankshaft | 98 | 72 |
|
||
Flywheel/Flex plate | Flywheel subassembly to Crankshaft | 130 | 96 |
|
||
Transfer | Transmission control cable assembly to Control shaft lever | 12 | 9 |
|
||
Drive/Axle shaft | Front drive shaft assembly RH to Bearing bracket | 32 | 24 |
|
||
Drive/Axle shaft | Drive shaft bearing bracket to Cylinder block | 64 | 47 |
|
steering torque settings
Save to email ✉️Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to |
---|
exhaust torque settings
Save to email ✉️Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
---|---|---|---|---|---|---|
Exhaust manifold | Front exhaust pipe assembly to Exhaust manifold converter subassembly | 43 | 32 |
|
||
Exhaust manifold | Front exhaust pipe assembly to Center exhaust pipe assembly | 43 | 32 |
|
||
Exhaust manifold | Center exhaust pipe assembly to Tail exhaust pipe assembly | 43 | 32 |
|
||
Exhaust manifold | Exhaust manifold converter subassembly to Cylinder head subassembly | 37 | 27 |
|
||
Exhaust manifold | Manifold stay to Exhaust manifold converter subassembly | 44 | 32 |
|
||
Exhaust manifold | Manifold stay to Cylinder block | 44 | 32 |
|
brakes torque settings
Save to email ✉️Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to | |
---|---|---|---|---|---|---|
Parking brake | Parking brake cable to Body | 5 | 4 |
|
suspension torque settings
Save to email ✉️Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to |
---|
general torque settings
Save to email ✉️Part | Description | Torque (Nm) | Torque (ft/lbs) | Remarks | Applies to |
---|
Did you find the answer to your specific question?
👍 3 👎 2